Geometric Dimensioning and Tolerancing for Mechanical Design Part 2 pps

... website. Introduction to Geometric Dimensioning and Tolerancing P1: PBU introduction1 MHBD0 31- Cogorno-v6.cls April 8, 2006 17 :58 Chapter 1 Introduction to Geometric Dimensioning and Tolerancing For many in ... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to...

Ngày tải lên: 05/08/2014, 09:20

... to Geometric Dimensioning and Tolerancing

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031- 02 MHBD031-Cogorno-v6.cls April 8, 20 06 18:6 Dimensioning and Tolerancing Fundamentals 11 44. 72 25 ° 10' ... Correct Incorrect +.000 0 0 +.00 1. .25 0 .25 0 40 40 −.005 −.005 −0.05 −.05 +. 025 +. 025 +0 .25 + .25 2. .25 0 .25 40 40 −.010 −.010 −0.10 −.1 .500 .5 4 .25...

Ngày tải lên: 05/08/2014, 09:20

... Correct Incorrect +.000 0 0 +.00 1. .25 0 .25 0 40 40 −.005 −.005 −0.05 −.05 +. 025 +. 025 +0 .25 + .25 2. .25 0 .25 40 40 −.010 −.010 −0.10 −.1 .500 .5 4 .25 4 .25 3. .548 .548 4.00 4 When specifying ... decimal point. TABLE 2- 3 Dimensional Limits 4.0 Means 4.000. . . 0 4 .2 Means 4 .20 0. . . 0 4 .25 Means 4 .25 0. . . 0 Dimensioning and Tolerancing for CAD/CAM Database Models...

Ngày tải lên: 05/08/2014, 09:20

... of Tolerance Form Profile Symbol Geometric Characteristics Figure 3- 23 Geometric characteristic symbols. 9. Write the names and geometric characteristic symbols where indicated in Fig. 3- 23. 10. The ... Slope Figure 3- 25 Geometric tolerancing symbols. 31 . Draw the indicated geometric tolerancing symbols in the spaces on Fig. 3- 25. 32 . What is the name of a physi...

Ngày tải lên: 05/08/2014, 09:20

... dimensioning a part. Figure 4- 4 shows a part with four holes. The designer selected the back of the part as the primary datum, datum A, because the back of the part mates with another part, and the ... PBU MHBD031- 04 MHBD031-Cogorno-v6.cls April 10, 2006 20:8 Datums 59 Figure 4- 13 Fixture for the part shown in Fig. 4- 14. Datum Targets Some manufacturing processes, suc...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-04 MHBD031-Cogorno-v6.cls April 10, 2006 20:8 1 .50 0 w 1.000- 1.030 4X .760 790 2 .50 0 1 .50 0 3.000 3 .50 0 1 .50 0 Figure ... by 1.020 1.018 1.016 1.014 1.010 1.0 05 1.000 21. Complete Table 5. 5 above specifying the straightness tolerance and what controls it for the drawin...

Ngày tải lên: 05/08/2014, 09:20

... at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031- 05 MHBD031-Cogorno-v6.cls April 11, 2006 20:17 Form 85 w Figure 5- 15 Straightness of a median ... 5- 1 Flatness Tolerances for the Part in Fig. 6-1 Actual part size Flatness tolerance Controlled by 1.020 .000 1.018 .002 Rule #1 1.016 .004 1.014 .0 05 1.010 .0 05 F...

Ngày tải lên: 05/08/2014, 09:20

... (www.digitalengineeringlibrary.com) Copyright â 20 06 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design ... 1° 2.00 3.00 Figure 6- 16 Specifying perpendicularity of a surface. 20. Supply the appropriate geometric tolerance on the drawing in Fig...

Ngày tải lên: 05/08/2014, 09:20

... (www.digitalengineeringlibrary.com) Copyright â 20 06 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design ... used of the 14 geometric characteristics. The position tolerance significantly contributes to part function, part interchangeability, o...

Ngày tải lên: 05/08/2014, 09:20

... 750 A A Ø 1.000 .99 6 Ø 1.004 1.000 Ø .751 755 Figure 9- 9 Specify coaxiality for the plug and socket—Problems 5 and 6. 5. Control the coaxiality of both parts shown in Fig. 9- 9 so that they will ... use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU Chapter08 MHBD031-Cogorno-v6.cls...

Ngày tải lên: 05/08/2014, 09:20

... given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031 -10 MHBD031-Cogorno-v5.cls April 11, 2006 23:3 Concentricity and Symmetry 173  The concentricity ... Concentricity is appropriately used for large, expensive parts that must have a small coax- ial tolerance for balance but need not have the same small tolerance fo...

Ngày tải lên: 05/08/2014, 09:20

... use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-12 MHBD031-Cogorno-v6.cls April 18, 2006 0:20 Profile ... sheet metal part in Fig. 12- 22 coplanar within .020. Tolerance holes with geometric tolerancing. The smallest size tolerance for each hole is the virtual condition for...

Ngày tải lên: 05/08/2014, 09:20

... use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-12 MHBD031-Cogorno-v6.cls April 18, 2006 0:20 190 ... sheet metal part in Fig. 12- 22 coplanar within .020. Tolerance holes with geometric tolerancing. The smallest size tolerance for each hole is the virtual condition for the...

Ngày tải lên: 05/08/2014, 09:20

... Strategy for Tolerancing Parts P1: PBU MHBD031-14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 A Strategy for Tolerancing Parts 235 flat on the outside diameter has been designated as datum C and specified as ... Strategy for Tolerancing Parts P1: PBU MHBD031-14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 A Strategy for Tolerancing Parts 233 8X Ø .500 540 Figure 14-10 A zero...

Ngày tải lên: 05/08/2014, 09:20