Design and development of a medical parallel robotfor cardiopulmonary resuscitation
DESIGN AND DEVELOPMENT OF MEDICAL ELECTRONIC INSTRUMENTATION A Practical Perspective of the Design, Construction, and Test of Medical Devices docx
... Page xiv In memory of Prof. Mircea Arcan, who was a caring teacher, a true friend, and a most compassionate human being. —David ffirs.qxd 11/22/2004 9:46 AM Page v 1 1 Design and Development of ... input parameters and provide you automatically with a schematic dia- gram and calculate capacitor and resistor values for specific filter implementations. This doesn’t mean...
Ngày tải lên: 29/03/2014, 11:20
The Design and Implementation of a Log-Structured File System
... The bandwidth of each of the five phases is shown separately. Sprite LFS has a higher write bandwidth and the same read bandwidth as SunOS with the exception of sequen- tial reading of a file that ... log as the most up to date ‘‘truth’’ about the state of the data on disk. The main difference is that database systems do not use the log as the final repository for data: a separ...
Ngày tải lên: 12/09/2012, 15:05
Design and development of major balance of plant components in solid oxide fuel cell system
... other than that provided by the anode off-gas given an anode off-gas temperature of less than 650 o C, a cathode off-gas temperature of less than 390 o C, and a flame barrier temperature of less ... a SOFC stack, an afterburner, a fuel heat exchanger and an air heat exchanger. As with any SOFC system, the performance of the INER SOFC system is dependent not only on t...
Ngày tải lên: 05/09/2013, 16:10
Design and Implementation of a Three-Phase Induction Motor Control Scheme
... A2 8 Gareth S Roberts 6. The MATLAB design The MATLAB design constructed is used to simulate the final FO control design where all parameters, processes and variables are modelled mathematically. ... advantages are clearly explained. Wildi also presents the two types of induction motors: “the squirrel cage induction motor” and the “wound motor”. An explanation of the adv...
Ngày tải lên: 27/10/2013, 23:15
Design and Simulation of A CMOS-MEMS Accelerometer
... major parameters of the device. Only the ratio of parasitic capacitance and sensing capacitance can be measured, and the estimated value is calculated assuming a total sensing capacitance of 60fF. ... of 60fF. Parasitic capacitance and mismatch of sensing capacitance is measured in a way as shown in Figure 5.4. The capac- itance ratios are derived from the ratios of driv...
Ngày tải lên: 27/10/2013, 23:15
Tài liệu Design And Simulation Of A Cmos-Mems Accelerometer doc
... performed on a probe station. Table 1 lists major parameters of the device. Only the ratio of parasitic capacitance and sensing capacitance can be measured, and the estimated value is calculated assuming ... assuming a total sensing capacitance of 60fF. Parasitic capacitance and mismatch of sensing capacitance is measured in a way as shown in Figure 5.4. The capac- itance...
Ngày tải lên: 22/12/2013, 08:16
Tài liệu Experiences in Design and Implementation of a High Performance Transport Protocol doc
... stream! Amsterdam Chicago 2 Chicago 1 Fairness and Friendliness 50 TCP flows and 4 UDT flows between SARA and StarLight Realtime snapshot of the throughput The 4 UDT flows have similar performance ... copy avoidance • Overlapped IO • Data scattering/gathering • Speculation of next packet Protocol Buffer Protocol Buffer User Buffer Data New Data Experiences in Design and...
Ngày tải lên: 15/01/2014, 15:59
Tài liệu The Design and Performance of a Real-time CORBA Event Service doc
... implemen- tations and (2) automating many common network program- ming tasks, such as object registration, location, and acti- vation; request demultiplexing; framing and error-handling; parameter marshalling ... T. Ralya, B. Pollak, R. Obenza, and M. G. Har- bour, A Practitioner’sHandbook for Real-Time Analysis: Guide to Rate Monotonic Analysis for Real-Time Systems. Norwell, Massa...
Ngày tải lên: 19/02/2014, 18:20