Part 3: Code of practice for imposed roof loads potx

... new Part to BS 6399 (formerly CP 3: Chapter V). Imposed roof loads were previously included in BS 6399-1. This new Part of BS6399 now gives more information on imposed roof loads and in particular ... the angle of pitch of the roof measured from the horizontal (a). For asymmetric pitched roofs, each side of the roof should be treated as one half of a corr...

Ngày tải lên: 08/07/2014, 22:20

... units BS 6399 : Loading for buildings BS 6399 : Part 2 : 1995 Code of practice for wind loads BS 6399 : Part 3 : 1988 Code of practice for imposed roof loads Other references [1] T. Ji and B. R Ellis. ... Reductions for intermediate areas may be calculated by linear interpolation. 7 Imposed roof loads For imposed roof loads refer to Part 3 of...

Ngày tải lên: 08/07/2014, 22:20

... workmanship: cold formed sections and sheeting. BS 6399-1, Loading for buildings Ð Code of practice for dead and imposed loads. BS 6399-2, Loading for buildings Ð Code of practice for wind loads. BS ... Ð Code of practice for wind loads. BS 6399-3, Loading for buildings Ð Code of practice for imposed roof loads. BS 8004, Code of practic...

Ngày tải lên: 08/07/2014, 22:20

... use of steelwork in building — Part 5: Code of practice for design of cold formed thin gauge sections. BS 5950-6, Structural use of steelwork in building — Part 6: Code of practice for design of ... 3.1: Code of practice for design of simple and continuous composite beams. BS 5950-4, Structural use of steelwork in building — Part 4: Code of pra...

Ngày tải lên: 08/07/2014, 22:20

... load D p Overall depth of profiled steel sheets D s Overall depth of composite slab d s Effective depth of slab to centroid of profiled steel sheets E Modulus of elasticity of profiled steel sheets F a End ... 3.5 of BS 8110-1:1985 or Tables 5.1 and 5.2 of BS 8110-2:1985. Figure 4 — Typical profiles BRITISH STANDARD BS 5950-4: 1994 Structural use of steelwork in building —...

Ngày tải lên: 08/07/2014, 22:20

... state D p Overall depth of the profile D w Sloping distance between the intersection points of a web and flanges (see figure 4) d Diameter of a fastener d p Diameter of a perforation d w Diameter of a washer E ... permissible deflection 1) for profiled sheeting under distributed loads Load condition Permissible deflection as a multiple of span Roof cladding Wall cladding Dea...

Ngày tải lên: 08/07/2014, 22:20

... 3.1: Code of practice for design of simple and continuous composite beams; — Section 3.2 1) : Code of practice for design of composite columns and frames; — Part 4: Code of practice for design of ... Specification for materials and workmanship: cold formed sections; — Part 8: Code of practice for fire resistant design; — Part 9 1) : Code of...

Ngày tải lên: 08/07/2014, 22:20

... steel sheeting; — Part 5: Code of practice for design of cold formed sections; — Part 6 1) : Code of practice for design of light gauge profiled sheeting; — Part 7: Specification for materials and ... cold formed sections; — Part 8: Code of practice for fire resistant design; — Part 9: Code of practice for stressed skin design. This Part of...

Ngày tải lên: 08/07/2014, 22:20

... for duopitch roofs 34 Figure 21 — Key for hipped roofs 37 Figure 22 — Key for mansard and multipitch roofs 38 Figure 23 — Key for multi-bay roofs 39 Figure 24 — Key for free-standing canopy roofs ... Keys for walls of inset storey 28 Figure 16 — Key for flat roofs 30 Figure 17 — Key to eave details for flat roofs 32 Figure 18 — Key for inset storey 32 Figure 19 — Key for...

Ngày tải lên: 08/07/2014, 22:20

... edition 2005-06-15 Information technology — Security techniques — Code of practice for information security management Technologies de l'information — Techniques de sécurité — Code de pratique ... guidelines This code of practice may be regarded as a starting point for developing organization specific guidelines. Not all of the controls and guidance in this cod...

Ngày tải lên: 21/02/2014, 10:20