Part 8: Code of practice for fire resistant design pot

... 3.1: Code of practice for design of simple and continuous composite beams; — Section 3.2 1) : Code of practice for design of composite columns and frames; — Part 4: Code of practice for design of ... Specification for materials and workmanship: cold formed sections; — Part 8: Code of practice for fire resistant design; — Part 9 1) :...

Ngày tải lên: 08/07/2014, 22:20

... cold formed sections; — Part 8: Code of practice for fire resistant design; — Part 9: Code of practice for stressed skin design. This Part of BS 5950 gives recommendations for the use of profiled ... steel sheeting; — Part 5: Code of practice for design of cold formed sections; — Part 6 1) : Code of practice for design of ligh...

Ngày tải lên: 08/07/2014, 22:20

... loads. CP 3, Code of basic data for the design of buildings 1) . CP 3: Chapter V, Loading. ISO 3898, Bases for design of structures — Notations — General symbols 1) . ISO 4355, Bases for design of structures ... area of a lower part of the roof, on which a drift could form, is not greater than 35 m 2 . For the purpose of this subclause the roof area is define...

Ngày tải lên: 08/07/2014, 22:20

... COPYRIGHT LAW Structural use of steelwork in building Ð Part 5. Code of practice for design of cold formed thin gauge sections BS 5950-5:1998  BSI 1998 17 Section 5. Design of members subject to bending 5.1 ... properties of fasteners Ð Bolts, screws and studs. CP3 Code of basic data for the design of buildings: Chapter V: Part 2: Wind loads. 1.4 Terms and d...

Ngày tải lên: 08/07/2014, 22:20

... use of steelwork in building — Part 5: Code of practice for design of cold formed thin gauge sections. BS 5950-6, Structural use of steelwork in building — Part 6: Code of practice for design of ... 3.1: Code of practice for design of simple and continuous composite beams. BS 5950-4, Structural use of steelwork in building — Part 4: Code of...

Ngày tải lên: 08/07/2014, 22:20

... recommendations for thedesign of composite slabs with profiled steel sheeting. It covers slabs spanning only in the direction of span of the profiled steel sheets. This code applies to the design of composite ... load D p Overall depth of profiled steel sheets D s Overall depth of composite slab d s Effective depth of slab to centroid of profiled steel sheets E Modul...

Ngày tải lên: 08/07/2014, 22:20

... used for the formed sections. For information, the resulting values of Y s and U s are also given in Table 4 together with appropriate design strength p y for the relevant grade. NOTE. Formability ... profile. 3.4.5 Profiles with acoustic perforations The section properties of sheet profiles incorporating a regular pattern of acoustic perforations should be calculated using the...

Ngày tải lên: 08/07/2014, 22:20

... units BS 6399 : Loading for buildings BS 6399 : Part 2 : 1995 Code of practice for wind loads BS 6399 : Part 3 : 1988 Code of practice for imposed roof loads Other references [1] T. Ji and B. R ... Schedule of weights of building materials BS 2573 : Rules for the design of cranes BS 2573 : Part 1 : 1983 Specification for classification, stress calculations...

Ngày tải lên: 08/07/2014, 22:20

... Keys for walls of inset storey 28 Figure 16 — Key for flat roofs 30 Figure 17 — Key to eave details for flat roofs 32 Figure 18 — Key for inset storey 32 Figure 19 — Key for monopitch roofs 33 Figure ... 33 Figure 20 — Key for duopitch roofs 34 Figure 21 — Key for hipped roofs 37 Figure 22 — Key for mansard and multipitch roofs 38 Figure 23 — Key for multi-bay roofs 39 Fig...

Ngày tải lên: 08/07/2014, 22:20

... Agreements with third parties may also involve other parties. Agreements granting third party access should include allowance for designation of other eligible parties and conditions for their access ... edition 2005-06-15 Information technology — Security techniques — Code of practice for information security management Technologies de l'information — Techniques de sé...

Ngày tải lên: 17/03/2014, 13:20