Autodesk Revit Architecture 2011 No Experience Required - part 61 docx

... regarding key- notes: in the Settings listings. Keynote Settings To find the keynote settings, follow this procedure: On the Tag panel of the Annotate tab, click the drop-down arrow on the bot- tom of ... Keynotes dialog box, your new keynote will be at the top of the list, as shown in Figure 11.101. 12. Pick the new keynote. 13. Click OK. The stairs now have a custom keynote. Are You Expe...

Ngày tải lên: 07/07/2014, 08:20

... 558 Using Multicategory Tags 565 Keynoting 568 Keynoting by Element 568 Keynoting by Material 571 Keynoting by User 574 Creating Keynote Legends 576 Are You Experienced? 578 ... 595 Drawing Detail Lines 615 Adding Notes 620 Adding Notes by Material 621 Adding Textual Notation 623 Creating Blank Drafting Views 626 Creating a Detail Group 634 Adding a Section to Another View 640 Importing .....

Ngày tải lên: 07/07/2014, 07:20

... walls in the model — it does not matter which one. 4. Right-click on the wall. 5. Select Create Similar, as shown in Figure 1.29. NOTE New to Revit 2011, when you right-click on an item, you can ... Geometry Now that you have some geometry to work with and you have some objects placed in your model, Revit starts to come alive. The benefits of using building information The Revit...

Ngày tải lên: 07/07/2014, 07:20

... Zoom into the northeast corner of the building, as shown in Figure 2.48. FIGURE 2.48 The northeast corner 2. Start the Wall command. Make sure it is the same 6 1⁄8″ two-hour partition you ... the top right of Figure 2 .61. 7. Pick the finish face of the exterior wall. You are selecting the gypsum layer to be cut out of the shaft (see Figure 2 .61) . FIGURE 2 .61 Click the Cut Profile .....

Ngày tải lên: 07/07/2014, 07:20

... Enter to delete an item. This is no lon- ger a good idea. If you do this to an item in Revit Architecture, it will only remove that element from the current view—not from the entire model. You ... Tool 223 Because these walls are not constrained to always be equal, if one exterior wall is moved, these five interior partitions will always maintain an equal relation- ship to one another—...

Ngày tải lên: 07/07/2014, 08:20

... www.sybex.com/go /revit2 011ner. From there you can browse to Chapter 9 and find these files: Toilet Stall-Accessible-Front-3D.rfa  Toilet Stall-Accessible-Side-3D.rfa  Toilet Stall-Braced-3D.rfa  Chapter ... files; then click Open. They are now loaded into your project. 3. On the Home tab, click the Place A Component button. 4. Select Toilet-Stall-Accessible-Front-3D-60″ × 60″ Clear....

Ngày tải lên: 07/07/2014, 08:20

... using AutoCAD Architecture: you do not need to tag an item in order for it to appear in a schedule in Revit Architecture. You can’t really just draft a sched- ule either. But this is not a bad situation ... create a mul- titude of schedules. The bad news is the Revit- produced schedules are not going to look like your company’s schedules at all. Before we go further, it is important...

Ngày tải lên: 07/07/2014, 08:20

... Category on the Annotate tab. 21. Pick any other corridor partition in the floor. Notice that this time the tag is automatically placed with the appropriate MC-1 tag filled out. O In Revit 2011, the ... east wing 3. On the Tag panel of the Annotate tab, click the Tag By Category but- ton, as shown in Figure 11 .61. FIGURE 11 .61 Click Tag By Category on the Annotate tab. 4. On the Opti...

Ngày tải lên: 07/07/2014, 08:20

... Annotate tab, select Keynote ➢ Element Keynote again. 7. Pick another wall sconce and place the keynote. Notice this tag is consistent throughout. Now that you have experience keynoting by element, ... Okay, maybe not that far back, but you get the point. Revit does a nice job in terms of tracking keynotes. The only issue is that nothing comes pre-keynoted in Revit. That is, a key...

Ngày tải lên: 07/07/2014, 08:20

... model, Revit will automatically tag it. Unlike other draft- ing applications, however, Revit does not rely on the tag for its information. Once a room is in the model, it can either contain or not ... parameters Revit looks for while placing a room into the floor plan. Because Revit draws from a database to gather information, the process of creat- ing a room boils down to you adding...

Ngày tải lên: 07/07/2014, 08:20