Autodesk Revit Architecture 2011 No Experience Required - part 37 doc

... extension (.rvt), which you can open and modify directly from either Revit Architecture, Revit Structure, or Revit MEP with absolutely no issues. This chapter will delve into the structural world using ... Items 334 Structural Grids Revit has entire books on this subject alone, so this book will address only the structural items available to people using Revit Architecture. I...

Ngày tải lên: 07/07/2014, 08:20

... 558 Using Multicategory Tags 565 Keynoting 568 Keynoting by Element 568 Keynoting by Material 571 Keynoting by User 574 Creating Keynote Legends 576 Are You Experienced? 578 ... Systems 364 Foundation Walls 365 Adding Structural Footings 370 Structural Slabs 372 Piers and Spread Footings 376 Structural Views 379 Are You Experienced? 381 ch A p t e r 9 Ceilings and Interiors ... 920 C...

Ngày tải lên: 07/07/2014, 07:20

... walls in the model — it does not matter which one. 4. Right-click on the wall. 5. Select Create Similar, as shown in Figure 1.29. NOTE New to Revit 2011, when you right-click on an item, you can ... they do not reflect the detail you will need to produce construction documents. Well, the great thing about Revit is that you have already done everything you need to do. You can now te...

Ngày tải lên: 07/07/2014, 07:20

... Zoom into the northeast corner of the building, as shown in Figure 2.48. FIGURE 2.48 The northeast corner 2. Start the Wall command. Make sure it is the same 6 1⁄8″ two-hour partition you ... command. NOTE If you receive an error that says “Ends of the sketched loop do not lie on the boundary of the face being modified” when you are trying to finish the sketch, it is because you have n...

Ngày tải lên: 07/07/2014, 07:20

... section. You do this when you need to show items that are not neces- sarily in line with one another. You can accomplish this in Revit Architecture as follows: 1. Open the Level 1 floor plan. ... item being cut, not allowing the geometry beyond to be seen. Start by opening your model, or go to www.sybex.com/go /revit2 011ner and browse to Chapter 3. Open the file called NER-07.rvt. If...

Ngày tải lên: 07/07/2014, 07:20

... Enter to delete an item. This is no lon- ger a good idea. If you do this to an item in Revit Architecture, it will only remove that element from the current view—not from the entire model. You ... Tool 223 Because these walls are not constrained to always be equal, if one exterior wall is moved, these five interior partitions will always maintain an equal relation- ship to one another—...

Ngày tải lên: 07/07/2014, 08:20

... or just a para- graph of text change the text type and arrowhead type for leader text Revit does not use an SHX font. As a mat- ter of fact, SHX can- not be used at all in Revit. It was ... You Experienced? 239 i W a n t t o C h a n g e a b u n C h o F t e x t a t o n C e ! Now you can. New to Revit 2011, you can use the new Find/Replace feature, shown here: Are You Experienced? N...

Ngày tải lên: 07/07/2014, 08:20

... 26. Press Esc twice to clear the command. 27. Select the roof. Notice there is a node where you picked the point. To access the node, click the Modify Sub Elements button on the Shape Editing ... corridor walls should look exactly the same but are now void of the con- crete parapet cap. FIGURE 7.21 Without the preview checked on, you will not be able to modify the parapet sweep. FIGURE .....

Ngày tải lên: 07/07/2014, 08:20

... Level 3. 3. The walls are now constrained to Level 3. 4. Go to Level 1 under Ceiling Plans (if it is not open already). The next procedure is a tad off-the-beaten-path but it fits squarely within ... the upper-right corner, as shown in Figure 9.11. 6. Click OK. The roof is now transparent. FIGURE 9.11 The View-Specific Element Graphics dialog Creating Ceilings 387 NOTE If you notice that...

Ngày tải lên: 07/07/2014, 08:20

... www.sybex.com/go /revit2 011ner. From there you can browse to Chapter 9 and find these files: Toilet Stall-Accessible-Front-3D.rfa  Toilet Stall-Accessible-Side-3D.rfa  Toilet Stall-Braced-3D.rfa  Chapter ... files; then click Open. They are now loaded into your project. 3. On the Home tab, click the Place A Component button. 4. Select Toilet-Stall-Accessible-Front-3D-60″ × 60″ Clear....

Ngày tải lên: 07/07/2014, 08:20