Autodesk Revit Architecture 2011 No Experience Required - part 16 doc
Autodesk Revit Architecture 2011 No Experience Required - part 16 doc
... section. You do this when you need to show items that are not neces-
sarily in line with one another. You can accomplish this in Revit Architecture as
follows:
1. Open the Level 1 floor plan.
... item
being cut, not allowing the geometry beyond to be seen.
Start by opening your model, or go to www.sybex.com/go /revit2 011ner and
browse to Chapter 3. Open the file called
NER-07.rvt. If...
Autodesk Revit Architecture 2011 No Experience Required - part 2 docx
... 558
Using Multicategory Tags 565
Keynoting 568
Keynoting by Element 568
Keynoting by Material 571
Keynoting by User 574
Creating Keynote Legends 576
Are You Experienced? 578
... Detail Lines 615
Adding Notes 620
Adding Notes by Material 621
Adding Textual Notation 623
Creating Blank Drafting Views 626
Creating a Detail Group 634
Adding a Section to Another View 640
Importing ... 904
Working...
Autodesk Revit Architecture 2011 No Experience Required - part 5 docx
... walls in the model — it does not matter which one.
4. Right-click on the wall.
5. Select Create Similar, as shown in Figure 1.29.
NOTE
New to Revit 2011, when you right-click on an item, you can ... example, we will mirror the two 16
′
–0
″
L-shaped walls to the
bottom of the building:
1. Type ZA (zoom all).
2. Near the two 16
′–0″ L-shaped walls, pick (left-click) and hold dow...
Autodesk Revit Architecture 2011 No Experience Required - part 11 docx
... Zoom into the northeast corner of the building, as shown in
Figure 2.48.
FIGURE 2.48 The northeast corner
2. Start the Wall command. Make sure it is the same 6 1⁄8″ two-hour
partition you ... command.
NOTE
If you receive an error that says “Ends of the sketched loop
do not lie on the boundary of the face being modified” when you are trying
to finish the sketch, it is because you have n...
Autodesk Revit Architecture 2011 No Experience Required - part 25 docx
... Enter to delete an item. This is no lon-
ger a good idea. If you do this to an item in Revit Architecture, it will only
remove that element from the current view—not from the entire model.
You ... Tool
223
Because these walls are not constrained to always be equal, if one exterior wall
is moved, these five interior partitions will always maintain an equal relation-
ship to one another—...
Autodesk Revit Architecture 2011 No Experience Required - part 27 doc
... or just a para-
graph of text
change the text type and arrowhead type for leader text
Revit does not use an
SHX font. As a mat-
ter of fact, SHX can-
not be used at all in
Revit. It was ... You Experienced?
239
i W a n t t o C h a n g e a b u n C h o F t e x t a t o n C e !
Now you can. New to Revit 2011, you can use the new Find/Replace feature,
shown here:
Are You Experienced?
N...
Autodesk Revit Architecture 2011 No Experience Required - part 33 doc
... 26. Press Esc twice to clear the command.
27. Select the roof. Notice there is a node where you picked the point. To
access the node, click the Modify Sub Elements button on the Shape
Editing ... corridor walls should look exactly the same but are now void of the con-
crete parapet cap.
FIGURE 7.21 Without the preview checked on, you will not be able to modify the
parapet sweep.
FIGURE .....
Autodesk Revit Architecture 2011 No Experience Required - part 37 doc
... extension (.rvt), which
you can open and modify directly from either Revit Architecture, Revit Structure,
or Revit MEP with absolutely no issues.
This chapter will delve into the structural world using ... Items
334
Structural Grids
Revit has entire books on this subject alone, so this book will address only the
structural items available to people using Revit Architecture. I...
Autodesk Revit Architecture 2011 No Experience Required - part 42 doc
... Level 3.
3. The walls are now constrained to Level 3.
4. Go to Level 1 under Ceiling Plans (if it is not open already).
The next procedure is a tad off-the-beaten-path but it fits squarely within ... the upper-right corner, as shown in Figure 9.11.
6. Click OK. The roof is now transparent.
FIGURE 9.11 The View-Specific Element Graphics dialog
Creating Ceilings
387
NOTE
If you notice that...
Autodesk Revit Architecture 2011 No Experience Required - part 44 docx
... www.sybex.com/go /revit2 011ner. From there you can browse to
Chapter 9 and find these files:
Toilet Stall-Accessible-Front-3D.rfa
Toilet Stall-Accessible-Side-3D.rfa
Toilet Stall-Braced-3D.rfa
Chapter ... files; then click Open. They are now loaded into your project.
3. On the Home tab, click the Place A Component button.
4. Select Toilet-Stall-Accessible-Front-3D-60″ × 60″ Clear....
Từ khóa: