Autodesk Revit Architecture 2011 No Experience Required - part 1 pot

... with no experience, Revit Architecture and its accompanying Web site will support you as you learn Revit at your own pace.”— Provided by publisher. ISBN 97 8-0 -4 7 0-6 10 1 1- 4 (pbk) ISBN 97 8-0 -4 7 0-9 046 5-7 ... print may not be available in electronic books. Library of Congress Cataloging-in-Publication Data Wing, Eric, 19 70 Autodesk Revit architecture...

Ngày tải lên: 07/07/2014, 07:20

... t ) The extension for a Revit Architecture file is .rvt. There are three separate Revit applications: Revit Architecture, Revit Structure, and Revit MEP. All three Revits share the same .rvt ... these steps: 1. Open the NER- 01. rvt file or your own file. 2. Go to Level 1. 3. On the Home tab, select the Door button. Chapter 1 • The Revit World 34 You are at a good point...

Ngày tải lên: 07/07/2014, 07:20

... Creating Views 10 2 TIP You may notice that speeding through the commands as you may have done in AutoCAD is not helping you any in Revit. In Revit you may need to slow down a bit, and let Revit “do ... model you have been working on, or go to www.sybex .com/go /revit2 011 ner, and browse to the Chapter 3 folder. Open the file called NER-05.rvt. If you wish, you can use an actual p...

Ngày tải lên: 07/07/2014, 07:20

... views. Choose Yes (see Figure 3 .11 ). Level 7 is now the Parapet level, as shown in Figure 3 .12 . FIGURE 3 .11 Click Yes to rename corresponding views. FIGURE 3 .12 : The renamed level 6. With the ... should now be two blank level lines above Level 4. 4. Select the West Parapet level. Notice some blue icons still appear. One of those icons says 3D. Creating Levels 11 1 5. Pick (left...

Ngày tải lên: 07/07/2014, 07:20

... using to follow along. If you have not completed the previous procedures, open the file called NER -1 2 .rvt found at the book’s website, www.sybex.com/go /revit2 011 ner. Go to Chapter 4 to find the ... reference plane, as shown in Figure 4. 31. FIGURE 4. 31 The window is now in alignment with the reference plane. Chapter 4 • Working with the Revit Tools 18 2 FIGURE 4.35 Open the sec...

Ngày tải lên: 07/07/2014, 08:20

... been working on. If you have not completed the previous chapter procedures, open the file caller NER -1 3 .rvt found at the book’s website, www.sybex.com/go /revit2 011 ner. Go to Chapter 4 to find ... Copy/Paste function. In Revit Architecture, you will use this feature quite a bit. There is no better way to com- plete a space or a layout on one level and then use that layout on anoth...

Ngày tải lên: 07/07/2014, 08:20

... you have been working on. If you have not com- pleted the previous tasks, open the file called NER -1 4 .rvt at the book’s website, www.sybex.com/go /revit2 011 ner. Go to Chapter 4 to find the file. To ... with. If you did not complete the previous chapter, go to the book’s website at www.sybex .com/go /revit2 011 ner. From there you can browse to Chapter 5 and find the file called NER -1 6...

Ngày tải lên: 07/07/2014, 08:20

... never have a Generic 12 ″ floor in your model, so it is a good idea not to keep this floor around. You are now in the Edit Assembly dialog. This is where you can specify a thick- ness for your slab. ... walls, as shown in Figure 6 .10 . You need to have a continuous loop— no gaps and no overlaps. 6. Apply some basic modify commands as well. For the right lower cor- ner, use the Trim c...

Ngày tải lên: 07/07/2014, 08:20

... Drain 277 13 . Repeat the steps to add a pitch to the lavatory north of the corridor. 14 . Save the model (see Figure 6. 51) . FIGURE 6.50 The final slab in the restroom FIGURE 6. 51 Both lavatories are now ... 10 ′–0″ (see Figure 6.52). 4. Hover your cursor over Level 1. Make sure the alignment line is below Level 1. When you see the alignment line, pick Level 1. You now have a...

Ngày tải lên: 07/07/2014, 08:20

... with. If you did not com- plete the previous chapter, go to the book’s web page at www.sybex.com/go/ revit2 011 ner. From there you can browse to Chapter 7 and find the file called NER-22.rvt. The objective ... [3]. 11 . Click in the Material cell. 12 . Click the […] button to open the Materials dialog. 13 . Select Insulation / Thermal Barriers - Rigid Insulation for the material....

Ngày tải lên: 07/07/2014, 08:20