SolidWorks 2010- P3 ppt

... dot (.) in the filename. The three document types are as follows: SolidWorks part file *.sldprt SolidWorks assembly file *.sldasm SolidWorks drawing file *.slddrw In this chapter, we’ll demonstrate ... becoming a SolidWorks master. Use Default Shortcuts Out of the box, SolidWorks comes with over 40 pre-programmed shortcut keys that in most cases will be more than enough for your daily...

Ngày tải lên: 01/07/2014, 22:20

... Tìm hiểu các bộ vi xử lý desktop của Intel: Phiên bản 2010 (p3) Core 2 Duo Các bộ vi xử lý Core 2 Duo là các thành viên đầu tiên của họ Core 2 và có đến hơn

Ngày tải lên: 14/12/2013, 14:15

... with SolidWorks 1 Start SolidWorks 2 SolidWorks License Agreement 3 Help and Workflow Customization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Navigate the SolidWorks ... team and is very well known in the SolidWorks community as the SolidWorks Geek, which is the name of his blog ( www.TheSWGeek.com ). Gabi Jack is a Certified SolidWorks Professio...

Ngày tải lên: 01/07/2014, 22:20

... accurate as possible. At a later date when you become more comfortable with modeling parts in SolidWorks, it would be great practice to design these components to finish your assembly. Here’s ... avoided this issue; the first is using a smaller radius for the fillet. If the fillet was smaller, SolidWorks wouldn’t have needed to change the geometry of the fillet to move around the boss. The...

Ngày tải lên: 01/07/2014, 22:20

... Prior to SolidWorks 2010, adding a center mark to a dimension circle or arc would result in a single solid line because the center mark would lie directly on top of the extension line. In SolidWorks ... creating a detached drawing. A detached drawing allows you to share the actual SolidWorks drawing with other SolidWorks users without the need for the model data. The advantage to...

Ngày tải lên: 01/07/2014, 22:20

... washer cover will be present only in the Open Documents field if the model is currently opened in SolidWorks. If you closed the model for the washer cover after creating it, you will need to select ... 6.21 Inserting washer cover into assembly There may be times in the future while you are using SolidWorks that you will need to insert multiple components into your assembly. Instead of se...

Ngày tải lên: 01/07/2014, 22:20

... assembly using the following steps: 1. Click New in the menu bar, and select Assembly in the New SolidWorks Document window. Click OK to create a new assembly model. 2. Click Browse in the Begin ... accept its default location. Since this is the first component being inserted into the assembly, SolidWorks can automati- cally specify the location of the part. Clicking the green check ma...

Ngày tải lên: 01/07/2014, 22:20

... outside source without including the actual 3D geometry. This allows other SolidWorks users to open a drawing in the native SolidWorks format without the model or assembly. Doing it this way saves ... The viewer can open and view SolidWorks native file formats and eDrawings formats. The advantage of using eDrawings is that you can send models and drawings to non -SolidWorks users. W...

Ngày tải lên: 01/07/2014, 22:20

Ngày tải lên: 24/09/2012, 14:16

Ngày tải lên: 29/10/2012, 08:59