Lasers Applications in Science and Industry Part 12 pptx

... volume, as shown in Figs. 8 and Fig. 9. Lasers – Applications in Science and Industry 218 irradiation of a certain number of laser pulses. The laser ablation and OCT imaging are repeated ... abruptly narrower in the dentine, reflecting the large difference in hardness between enamel and dentine. In addition, in the real-time imaging shown in Fig. 5, a s...

Ngày tải lên: 18/06/2014, 22:20

... image quality while introducing a minor increase in the size of the object, all without changing the optical imaging parameters. Lasers – Applications in Science and Industry 96 1.2 Pulsed ... (1) w - grating period λ - desorbing laser wave length Part 2 Laser-Matter Interaction Lasers – Applications in Science and Industry 110 Fig. 1. Laser-matter...

Ngày tải lên: 18/06/2014, 22:20

... aluminum alloy is about twice that of the 2024 aluminum alloy. Lasers – Applications in Science and Industry 174 Fig. 1. Schematic representation of propagation of pitting corrosion in ... becomes lower with increasing aspect ratio. 4. The repassivation ratio at 0.01 s after activation becomes lower with increasing aspect ratio. Lasers – Applications in Sc...

Ngày tải lên: 18/06/2014, 22:20

... Lasers – Applications in Science and Industry 8 temperature of the ZnSe crystals increases. In the case of pulse lasers, an increases in the transient temperature ΔT in materials ... hexagonal and the orientation of each diffraction point is Lasers – Applications in Science and Industry Edited by Krzysztof Jakubczak Published by In...

Ngày tải lên: 18/06/2014, 22:20

... shown in Fig. 11(a). Lasers – Applications in Science and Industry 28 4. Depositing high LIDT coatings at Sandia’s large optics coating operation Coating large optics goes hand in hand with ... detail in this chapter. Regarding the polishing and preparing of optics for coating, we have demonstrated in the case of an AR coating that using one combination of polish...

Ngày tải lên: 18/06/2014, 22:20

... coating requirements demonstrates the critical role that coating design plays in obtaining coatings Lasers – Applications in Science and Industry 42 and this interference leads to intensity ... uniform Lasers – Applications in Science and Industry 50 Regarding polishing, washing and cleaning of an optic prior to coating it, we point out that residual...

Ngày tải lên: 18/06/2014, 22:20

... coupling Lasers – Applications in Science and Industry 58 We observed that only AlN was detected in the films obtained with laser sources B and C, while films obtained with source A contain ... 20 minutes. Fig. 1. PLD general setup used in the experiments reviewed in this chapter Lasers – Applications in Science and Industry 66 to the vibration...

Ngày tải lên: 18/06/2014, 22:20

... Lasers – Applications in Science and Industry 82 melting m T and vaporization f T points are 512 °C and 738 °C, respectively. It should be noted that f T is determined by the cross point ... itself and remains in the equilibrium state, and thus inherits the structure and volume at the melting state. Therefore, the volume has an increase V , and Lasers –...

Ngày tải lên: 18/06/2014, 22:20

... fiber and supercontinuum spectrum. (Courtesy of Dr. Ping Ying and Dr. Zairu Ma) Lasers – Applications in Science and Industry 120 Fig. 3.5. The ripples of SiO 2 antireflection coating ... to induce ionization and the material cannot directly absorb incident laser of low intensity. Photo-ionization consists Lasers – Applications in Science and Industry...

Ngày tải lên: 18/06/2014, 22:20

... treated in this chapter is the difference in refractive index of a transparent material from that of the adjacent medium. Lasers – Applications in Science and Industry 134 In this study, ... combination of a silica glass plate in contact with distilled water layer. Figure 2.2 shows the typical results. In this case, pulse laser is focused Lasers – Application...

Ngày tải lên: 18/06/2014, 22:20