Daewoo matiz 2000 2013 manual transaxle drive axle hệ thống truyền lực trên xe matiz đời 2000 2013

... 3B –2 MANUAL TRANSAXLE DRIVE AXLE DAEWOO M-150 BL2 DESCRIPTION AND OPERATION FRONT DRIVE AXLE Drive axles are flexible shaft assemblies that transmit a rotational force from the transaxle to ... –6 MANUAL TRANSAXLE DRIVE AXLE DAEWOO M-150 BL2 D104B502 7. Pull the drive axle shaft (1) from the wheel hub. Important: Support the unfastened end of the drive axl...

Ngày tải lên: 28/05/2014, 15:29

... SYSTEM 9T – 25 DAEWOO M–150 BL2 COMMUNICATION BETWEEN IMMOBILIZER CONTROL UNIT AND TEST EQUIPMENT (FENIX 5MR) 1. Connect the test equipment as described in the Scan Tool Equipment Manual. 2. If ... field, and receives data and commands in a similar way. D105A504 DETECTION COIL (Left–Hand Drive Shown, Right–Hand Drive Similar) Removal Procedure 1. Remove the steering column covers. Ref...

Ngày tải lên: 28/05/2014, 15:27

... side. 1. DRAIN AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle) (a) for 2GR-FE: See page AX-207 (b) for 2AZ-FE: See page AX-162 2. DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle) (See page MX-5) 3. ... ft.*lbf) 10. ADD AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle) (a) for 2GR-FE: See page AX-164 (b) for 2AZ-FE: See page AX-175 11. ADD MANUAL TRANSAXLE OIL (for...

Ngày tải lên: 24/05/2014, 13:30

... REMOVE PROPELLER SHAFT FROM TRANSAXLE (a) Remove the 2 bolts and center support bearing. (b) Pull out the propeller shaft yoke from the transaxle. (c) Insert SST in the transaxle to prevent oil leakage. SST ... ASSEMBLY PR−7 1996 RAV4 (RM447U) REPLACEMENT REPLACE DUST COVER (a) Using a screwdriver and hammer, remove the dust cover. (b) Using 2 screwdrivers and hammers, install a new dus...

Ngày tải lên: 24/05/2014, 16:29

... RESTRAINTS (SIR) 8B– 3 DAEWOO M-150 BL2 DESCRIPTION AND OPERATION (Left–Hand Drive Shown, Right–Hand Drive Similar) AIRBAG MODULE Driver Airbag Module Caution: Tampering with the driver side airbag module ... . . . . . . . . . . DTC 18 Connection Between Driver Firing Circuit and Driver Pretensioner Circuit 8B-46. . . . . DTC 19 Connection Between Driver Firing Circuit and Passenger...

Ngày tải lên: 28/05/2014, 13:06

... Fixture DW210–010 Clutch Center Guide Removal Procedure 1. Remove the transaxle from the vehicle. Refer to Sec- tion 5B, Manual Transaxle. 2. Support the engine to normal position using the en- gine ... Shaft 09943–88211 Bushing, Bearing Installer Removal Procedure 1. Remove the transaxle from the vehicle. Refer to Sec- tion 5B, Manual Transaxle. 2. Remove the release arm. Refer t...

Ngày tải lên: 28/05/2014, 13:07

... DAEWOO M-150 BL2 SECTION 9M EXTERIOR TRIM TABLE OF CONTENTS Description and Operation 9M-2. . . ... Tailgate Handle 9M-5. . . . . . . . . . . . . . . . . . . . . . . . . . . 9M –2 EXTERIOR TRIM DAEWOO M-150 BL2 DESCRIPTION AND OPERATION EMBLEMS AND LETTERING The emblems and lettering on the ... all models. Mud guards will help prevent an excessive buildup of mud on the body. EXTERIOR TR...

Ngày tải lên: 28/05/2014, 13:09

... INTERIOR TRIM DAEWOO M-150 BL2 D109E578 Installation Procedure 1. Install the parking brake cable cover with the screw. D109E581 FLOOR CARPET (Left–Hand Drive Shown, Right–Hand Drive Similar) Removal ... trim panel with the plastic screws. 9G –18 INTERIOR TRIM DAEWOO M-150 BL2 SPECIAL TOOLS AND EQUIPMENT SPECIAL TOOLS TABLE D109E101 KM-475-B Trim Remover DAEWOO M-150 BL2 SECTION 9G...

Ngày tải lên: 28/05/2014, 15:28

... They will come on when the transaxle is shifted into REVERSE. On a vehicle with a manual transaxle, they are activated by a reverse switch which is part of the transaxle. DAYTIME RUNNING LAMPS ... 9B–20 LIGHTING SYSTEMS DAEWOO M-150 BL2 TAIL AND LICENSE PLATE LAMPS CIRCUIT D19D203B LIGHTING SYSTEMS 9B – 21 DAEWOO M-150 BL2 STOPLAMPS CIRCUIT D19D204B 9B–22 LIGHTING SYSTEMS DAEWOO...

Ngày tải lên: 28/05/2014, 15:29

... (100g). 4. INSTALL RELEASE BEARING AND FORK TO TRANS- AXLE Install the bearing to the release fork, and then install them to the transaxle. 5. INSTALL TRANSAXLE TO ENGINE (2WD: See page MX−2) (4WD: See ... the clutch disc. NOTICE: Do not drop the clutch disc. 3. REMOVE RELEASE BEARING AND FORK FROM TRANSAXLE (a) Remove the release bearing together with the fork and then separate them....

Ngày tải lên: 24/05/2014, 16:24