4 lab

Ngày tải lên: 13/05/2014, 03:03

... bandwidth (BW) for interface Serial 0? 1 544 Kbit (or 1. 544 Mbps) Cisco CCNA Optional Semester Labs – Wide Area Networking LAB – T1 / TSU WAN LINK – ANSWERS Step – Test the WAN Connection between the ... server (no Telnet daemon) Cisco CCNA Optional Semester Labs – Wide Area Networking LAB – T1 / TSU WAN LINK – SETUP GUIDE Instructo...

Ngày tải lên: 12/07/2014, 12:46

... tra kết quả: Router(config)#exit Router#show ip route Router#show ip protocol Router#debug ip rip www.ipmac.com.vn

Ngày tải lên: 13/11/2012, 10:56

... Router(config-router)# version Giao thức định tuyến sử dụng để nhận gửi gói tin Ripv2 Router(config-router)# version Giao thức định tuyến sử dụng để nhận gửi gói tin Ripv1 Router(config-if)# ip rip send version ... nhận gói tin version Ripv1 qua interface Router(config-if)# ip rip receive Router nhận gói tin version Ripv2 qua interface Router(config-if)# ip rip receive Router nhận g...

Ngày tải lên: 27/04/2013, 15:33

... Address) The available addresses for the WAN links can be taken from the available addresses in each of the /30 subnets 5-5 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 1.1.4 Copyright ... their subnet Fourteen useable addresses are available in this range for the hosts 3-5 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 1.1.4 Copyright  2003, Cisco S...

Ngày tải lên: 16/10/2013, 20:15

... encapsulation type to PPP by typing encapsulation ppp at the interface serial configuration mode prompt on both routers Brasilia(config-if)#encapsulation ppp Warsaw(config-if)#encapsulation ppp b What did ... v 3.0 - Lab 3.3.4 Copyright  2003, Cisco Systems, Inc • • Turn the router off • 4-6 Logoff by typing exit Remove and store the cables and adapter CCNA 4: WAN Technologies...

Ngày tải lên: 19/10/2013, 02:15

... the chart at the end of the lab to correctly identify the interface identifiers to be used based on the equipment in the lab The configuration output used in this lab is produced from 1721 series ... Establishing a HyperTerminal session lab Erase and reload all routers in this lab assignment before continuing If there are problems in accomplishing this, go to lab 4.2.6 and use tho...

Ngày tải lên: 23/10/2013, 00:15

... new password: Password changed DLSwitch1> (enable) set enablepass Enter old password: (Because you not currently have a password, just hit enter) Enter new password: Retype new password: Password ... Attempt to telnet into the Catalyst switch You will not be able to get in because you not know the passwords The Catalyst 4000 series of switches deals with password recovery m...

Ngày tải lên: 23/10/2013, 00:15

... d Is show one of the options available? _ Step Display help for the show command a Enter the show ? command The router responds with the show subcommands available in ... the router prompt The router responds with all commands available in user mode b What did the router reply with? c Are all router commands available at the current prompt? ... three user mode show s...

Ngày tải lên: 27/10/2013, 07:15

... ISDN BRI interface The string in parenthesis is the legal abbreviation that can be used in IOS command to represent the interface 4-4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 4.1.4 Copyright ... for a password, enter class If “class” does not work, ask the instructor for assistance Router>enable At the privileged EXEC mode, enter the command erase startup-config Router#erase start...

Ngày tải lên: 04/11/2013, 16:15

... about them Refer to prior labs on configuring Serial and Ethernet interfaces and making changes to configurations if you need help b What is the clock rate to be set to and which interface is it ... by typing exit Turn the router off 2-4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 4.1.4 Copyright  2003, Cisco Systems, Inc Erasing and reloading the router Enter into the pr...

Ngày tải lên: 05/11/2013, 12:15

... _ d Global CDP settings can be seen using the show cdp command by itself e What information is not shown in the show cdp command? _ Step Display the CDP updates received ... Routers and Routing Basics v 3.0 - Lab 4.1.6 Copyright  2003, Cisco Systems, Inc Step 10 Observe CDP packets being sent and received on the router a Enter the debug cdp packets command from the privil...

Ngày tải lên: 05/11/2013, 12:15

... Reassign the root bridge a It has been determined that the switch selected as the root bridge, by using default values, is not the best choice It is necessary to force the “other” switch to become the ... What is the status of the link light on the blocking port? Step Verify the running configuration file on the root switch a On the switch that was changed to...

Ngày tải lên: 05/11/2013, 12:15

... _ d Global CDP settings can be seen using the show cdp command by itself e What information is not show in the show cdp command? _ Step Display the CDP updates received ... 10 Observe CDP packets being sent and received on the router a Enter the debug cdp packets command from the privileged exec mode 3-6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 4.1.6 Copyright ... 11 O...

Ngày tải lên: 11/12/2013, 14:15