Camry Repair Manual 90 EWD

... listed in this manual, refer to the following manuals; Manual Name Pub. No. S1 990 Camry Repair Manual Volume 1 Volume 2 STCCS (3S–FE) Diagnosis Manual SECT (A140E) Diagnosis Manual SECT (A540E) ... diagram manual has been prepared to provide information on the electrical system of the 1 990 TOYOTA CAMRY. Applicable models: SV21, 25 series VZV21 series For service specifi...

Ngày tải lên: 29/04/2014, 08:54

... year vehicle, refer to the following manuals: Manual Name Pub. No. . 1 990 Celica New Car Features . 1 990 model Repair Manuals . 1 990 model Electrical Wiring Diagram Manuals NCF056U Refer to the respective located Pub. ... the 1 990 model year to raise the Camry s product appeal. 1. 3S–FE Engine Plastic region tightening is used for the cylinder head bolts for good axial tension. R...

Ngày tải lên: 29/04/2014, 08:55

... If leak is found, repair the faulty component or connection. CAUTION: Use the refrigerant recovery/ recycling machine to recover the refrigerant whenever replacing parts. N13 790 Low Pressure Service ... sure to read the following item carefully, then follow the correct procedure described in the repair manual. AC21Y–01 I03338 Thermometer Ice 10 cm (0.39 in.) Ohmmeter Thermistor Z04352...

Ngày tải lên: 28/04/2014, 12:52

... Q10051 AX03A–01 AX–10 –AUTOMATIC TRANSAXLE (A140E) SHIFT SOLENOID VALVE SL 1903 A uthorĂ: DateĂ: SHIFT SOLENOID VALVE SL ON–VEHICLE REPAIR 1. REMOVE PARK/NEUTRAL POSITION SWITCH (See page AX–4) 2. DISCONNECT ... AX–4) Q00394 SST AX03B–01 Q00247 SST –AUTOMATIC TRANSAXLE (A140E) DIFFERENTIAL OIL SEAL AX–11 1904 A uthorĂ: DateĂ: DIFFERENTIAL OIL SEAL ON–VEHICLE REPAIR 1. REMOVE LH AND RH D...

Ngày tải lên: 28/04/2014, 12:53

... transversely–mounted engine. AX0EP–02 INTRODUCTION HOW TO USE THIS MANUAL IN–1 HOW TO USE THIS MANUAL To assist you in finding your way through the manual, the Section Title and major heading are given at ... shim thickness 1 .90 mm 0.0748 in. 1.95 mm 0.0768 in. 2.00 mm 0.0787 in. 2.05 mm 0.0807 in. 2.10 mm 0.0827 in. 2.15 mm 0.0846 in. 2.20 mm 0.0866 in. 2.25 mm 0.0886 in. 2.30 mm 0. 0...

Ngày tải lên: 28/04/2014, 13:01

... lock manual switch OFF or UNLOCK No continuity A16 – Ground Door lock manual switch LOCK Continuity A17 – Ground Door lock manual switch OFF or LOCK No continuity A17 – Ground Door lock manual ... Door lock manual switch OFF or UNLOCK No continuity A1 – Ground Door lock manual switch LOCK Continuity A2 – Ground Door lock manual switch OFF or LOCK No continuity A2 – Ground Door l...

Ngày tải lên: 28/04/2014, 13:03

... lock manual switch OFF or UNLOCK No continuity A16 – Ground Door lock manual switch LOCK Continuity A17 – Ground Door lock manual switch OFF or LOCK No continuity A17 – Ground Door lock manual ... Door lock manual switch OFF or UNLOCK No continuity A1 – Ground Door lock manual switch LOCK Continuity A2 – Ground Door lock manual switch OFF or LOCK No continuity A2 – Ground Door l...

Ngày tải lên: 28/04/2014, 13:07

... TRAC): Using SST, disconnect the 4 brake lines. SST 0902 3–00100 Torque: 15 N·m (155 kgf·cm, 11 ft·lbf) (b) w/o ABS: Using SST, disconnect the 5 brake lines. SST 0902 3–00100 Torque: 15 N·m (155 kgf·cm, 11 ... TRAC: REMOVE PISTON STOPPER BOLT Using a screwdriver, push the pistons in all the way and remove the piston stopper bolt and gasket. HINT: Tape the screwdriver tip before use. Torque: 1...

Ngày tải lên: 28/04/2014, 13:08

Ngày tải lên: 28/04/2014, 13:08

... DISCONNECT CLUTCH LINE Using SST, disconnect the line. Use a container to catch the fluid. SST 0902 3–00100 Torque: 15 N·m (155 kgf·cm, 11 ft·lbf) 2. REMOVE 2 BOLTS AND PULL OUT RELEASE CYL- INDER Torque: ... CYL- INDER Torque: 12 N·m (120 kgf·cm, 9 ft·lbf) CL03D–01 Q05878 –CLUTCH CLUTCH RELEASE CYLINDER CL–11 1790AuthorĂ: DateĂ: DISASSEMBLY 1. REMOVE BLEEDER PLUG 2. PULL OUT BOOT WITH PUSH R...

Ngày tải lên: 28/04/2014, 13:08