Tài liệu Handbook of Production Management Methods pdf

... PM 108 Handbook of Production Management Methods community is just becoming aware of them. Some engineering types con- templating concurrent engineering don’t consider soft skills training much of a ... 2001 5:00 PM 104 Handbook of Production Management Methods Bibliography 1. Albus, J., Barbera, A. and Nagel, N., 1981: Theory and practice of hierarchical control. I...

Ngày tải lên: 13/02/2014, 16:20

... and money; and most of all – to make profit. The manufacturing environment may differ with respect to: • size of plant; • type of industry; • type of production (mass production, job shop, ... routing • production management: MRP, capacity planning, scheduling, dispatching, etc. 0750650885-ch001.fm Page 1 Friday, September 7, 2001 4:53 PM 2 Handbook of Production M...

Ngày tải lên: 22/03/2014, 12:20

Ngày tải lên: 22/12/2013, 23:17

... concentration of oxygen at the head 26 Chapter One Head Coated alloy Tail X Front of head Back of head Direction of propagation Figure 1.10 Illustration of the filament nature of filiform corrosion. 0765162_Ch01_Roberge ... normalize the value of the current by the surface area of the electrode and use the current density, often expressed as a small i, i.e., i ϭ I/surface area...

Ngày tải lên: 22/12/2013, 23:17

Ngày tải lên: 23/12/2013, 01:16

... di where Z 2 = number of teeth of larger pulley Zi = number of teeth of smaller pulley d 2 = pitch diameter of larger pulley di = pitch diameter of smaller pulley Datum length: / ... safety, since the probability of sudden failure of a complete belt set is very small. The uniformity of initial tensions and speed ratios of all belts of mult...

Ngày tải lên: 20/01/2014, 01:20

... classification chart of Fig. 30.7: mechanical, pneumatic (or hydraulic), electric, and automatic. Sometimes the methods are combined. The drum brake of Fig. 30.8 and the disk brake of Fig. ... An advantage of the non-self-energizing disk brake is its great stability; it is relatively insensitive to changes in the coefficient of friction. Brake Actuation....

Ngày tải lên: 20/01/2014, 01:20

... of single-roller contact line, in (mm) Values of the constant M are listed in Table 27.2. TABLE 27.2 Value of Constant M for Use in Eqs. (27.1) and (27.2) Constant M Type of ... bearing is to be selected to carry a radial load of 4 kN and have a reliability of 0.99 at 1200 hours (h) and a speed of 600 revolutions per minute (r/min). Thus L D...

Ngày tải lên: 20/01/2014, 01:21

... 5.7 on the universality of the next-bit test is due to Yao [1258]. For a proof of Yao’s result, see Kranakis [710] and §12.2 of Stinson [1178]. A proof of a generalization of Yao’s result is given ... non-overlappingparts each of length m,andletn i be the number of occurrences of the i th type of sequence of length m, 1 ≤ i ≤ 2 m . The poker test determines whether the seq...

Ngày tải lên: 26/01/2014, 00:20

... effects that SiliconValley models are designed to produce. One of the central tenets of somerecent discussion of the behavior of senior of cials in the public sector, is the view that those engagedinthe ... order of $7 billion during the second quarter of 2000 29 provides someindication of the money required to fuel it. Only alimited number of good ideas result in start-ups....

Ngày tải lên: 15/02/2014, 20:20