Tài liệu ANALOG BEHAVIORAL MODELING WITH THE VERILOG-A LANGUAGE- P2 ppt
Tài liệu ANALOG BEHAVIORAL MODELING WITH THE VERILOG-A LANGUAGE- P1 pdf
... change. As such, the material in this book focuses on the core aspects of the Verilog-A language as presented in the LRM and the work within the OVI Verilog-A Technical Subcommittee. The goal of this ... book is to provide the designer a brief introduction into the methodol- ogies and uses of analog behavioral modeling with the Verilog-A language. In doing so...
Ngày tải lên: 26/01/2014, 19:20
Tài liệu ANALOG BEHAVIORAL MODELING WITH THE VERILOG-A LANGUAGE- P2 ppt
... design. The behavioral description is done in a programmatic fashion in the Verilog-A lan- guage within the analog statement or block of the module. The analog block encapsulates the behavioral ... Because of mathematical and other properties associated with analog opera- tors, there are special considerations in their usage. These and other issues associated with...
Ngày tải lên: 26/01/2014, 19:20
Tài liệu ANALOG BEHAVIORAL MODELING WITH THE VERILOG-A LANGUAGE- P3 doc
... complete the transition in the specified time. If the new final value level is below the value level at the point of the interruption (the current value), transition uses the old destination as the ... encapsulated within the analog statement. The analog statement encompasses the contribution state- ment(s) that are used to define the relationships between the...
Ngày tải lên: 26/01/2014, 19:20
Tài liệu ANALOG BEHAVIORAL MODELING WITH THE VERILOG-A LANGUAGE- P4 pptx
... from the type of the value of the default value expression. If the type of the parameter is specified, and the value of the default expression conflicts with the declared type of the parameter, the ... assertion check. The qualifiers for the range specification include either from or exclude . If the keyword from is used, the value of the parameter must be wit...
Ngày tải lên: 26/01/2014, 19:20
Tài liệu ANALOG BEHAVIORAL MODELING WITH THE VERILOG-A LANGUAGE- P5 ppt
... step on the stimulus signal that provides the input to the operational amplifier. The measurement module then senses the crossings of the output of the module when they are within +/- 5% of the final ... use of the cross analog operator. The control signal is then compared to its threshold value to determine the state of the switch. The variable that is set is then...
Ngày tải lên: 26/01/2014, 19:20
Tài liệu ANALOG BEHAVIORAL MODELING WITH THE VERILOG-A LANGUAGE- P6 doc
... scale, shaft_angle; analog begin if (Theta(shaft) > max_theta) shaft_angle = max_theta; else if (Theta(shaft) < min_theta) shaft_angle = min_theta; else shaft_angle = Theta(shaft); scale ... friction, The back voltage generated by the motor is times the angular frequency of the motor, , and the torque is times the current through the motor, This is shown diagrammatically...
Ngày tải lên: 26/01/2014, 19:20
Tài liệu ANALOG BEHAVIORAL MODELING WITH THE VERILOG-A LANGUAGE- P7 docx
... contains the coefficients of the numerator. For the denominator, is the vector of N real pairs, one for each pole where the first number in the pair is the real part of the zero, and the second is the ... represents a zero, the first number in the pair is the real part of the zero, and the second is the imaginary part. Similarly, d is the vector of N real coe...
Ngày tải lên: 26/01/2014, 19:20
Tài liệu ANALOG BEHAVIORAL MODELING WITH THE VERILOG-A LANGUAGE- P8 docx
... The device element cards in Spice then reference the model name. Each device element card contains the device name, the nodes to which the device is connected to, and the device model name. The ... for Spice. The first card in the input deck must be a title card, and the last card must be the .END control line. The order of the remaining element and control lines is...
Ngày tải lên: 26/01/2014, 19:20
ANALOG BEHAVIORAL MODELING WITH THE VERILOG-A LANGUAGE- P9
... for Spice. The first card in the input deck must be a title card, and the last card must be the .END control line. The order of the remaining element and control lines is arbitrary. The input ... element in the circuit is specified by an element line that contains the element name, the circuit nodes to which the element is connected, and the values of the parameters...
Ngày tải lên: 18/10/2013, 00:15
Tài liệu Module 7: Working with the Microsoft Outlook 2000 Object Model pptx
... using the Panes property on that object. Once you retrieve the Panes collection, you can use the Item method of the Panes object and pass in either the numeric index or the name of the Pane ... string that specifies the name of the group to add; the other is optional and specifies a number indicating the insertion position for the new Outlook group. The top of t...
Ngày tải lên: 10/12/2013, 16:15