Tài liệu Writing and Understanding Loop Conditions doc

... while loop. In the next exercise, you put this list to work by making something happen when you click a list item. < Day Day Up > < Day Day Up > Writing and Understanding ... statement of the loop itself. On the tenth loop, i = 10, which means that i < 10 is no longer true, and the loop halts. You can also use the decrement operator with a loop,...

Ngày tải lên: 26/01/2014, 12:20

... method for writing each type of document and develop formats and contents. ü Third, after documents are approved they will be released into engineering document control. Engineering document control ... Ap- proval and Issue: The supplier shall establish and maintain procedures to control all documents and data that relate to the requirements of this international standard. These d...

Ngày tải lên: 09/12/2013, 21:15

... using the username pix and the password set with the enable password command. Step 4 Save the commands in the configuration using the write memory command. Example 9-4 shows commands for using Telnet ... by the PIX Firewall for monitoring and configuring the system, and for monitoring network activity. It contains the following sections: • Command Authorization and LOCAL User Authenti...

Ngày tải lên: 11/12/2013, 13:15

... where N stands for the number of docu- ments in the collection and df (t) is the number of documents that contain the term (the so-called document frequency of t). Given a document vector d and a query ... applied to. Altogether, a filter [loop1 fexp1] of XP1 is subsumed by a filter [loop2 fexp2] of XP2 which is attached to the same node, if loop1 is subsumed by loop2 and fexp1i ⇒ fex...

Ngày tải lên: 14/12/2013, 15:16

... primitive nand gates // Note, how the wires are connected in a cross-coupled fashion. nand n1(Q, Sbar, Qbar); nand n2(Qbar, Rbar, Q); // endmodule statement endmodule // Module name and port ... module are q, qbar, set, and reset. The root module instantiates m1, which is a module of type SR_latch. The module m1 instantiates nand gates n1 and n2. Q, Qbar, S, and R are port...

Ngày tải lên: 15/12/2013, 03:15

... input timing constraints can also be specified. 10.3.1 $setup and $hold Checks $setup and $hold tasks are used to check the setup and hold constraints for a sequential element in the design. ... IEEE Standard Verilog Hardware Description Language document. The various steps in the flow that use delay back-annotation are as follows: 1. The designer writes the RTL description and...

Ngày tải lên: 15/12/2013, 03:15

... equipment and the eight E1 lines from the network. The LTU is used for loopback testing, system maintenance and intrusive E1 testing. A non-intrusive monitor jack is also accessible for monitoring and ... Soneplex E1 Quad Loop Extender (EQLX) Four-Position Remote Chassis houses up to four EQLX modules and optional line termination unit, power supply unit, E1 alarm processor unit an...

Ngày tải lên: 21/12/2013, 06:15

... Course and the MSF Process Model 25 Vision Approved Milestone Deliverables 26 This Course and the Vision Document 27 Looking Forward 28 Module 2: Identifying Business Processes, Challenges, and ... Studio, and SQL Server are either registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and/ or other countries. The names of companies, products, people, cha...

Ngày tải lên: 21/12/2013, 06:16

... internal and external resources and facilitates extra control and monitoring of Web traffic. Using ClusterCATS with NAT: 1 Before creating a cluster, you must configure the source of internal and ... Java and CORBA. These pages make up the Administrator Extensions section: • JVM and Java Settings • Java Applets • CFX Tags • Custom Tag Paths • CORBA Connectors JVM and Java Set...

Ngày tải lên: 21/12/2013, 20:15