Tài liệu RAZOR HANDLE Using Swept Blend pptx

... surfaces of the handle as shown below. Pick the top two surfaces by left- click mouse button. 1 ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN RAZOR HANDLE Using Swept Blend Pro/ENGINEER ... Swept Blend Pro/ENGINEER Wildfire 2.0 Dr. Herli Surjanhata Create Swept Blend Protrusion of Razor Handle Set the working directory to e.g. ME-430 di...

Ngày tải lên: 25/01/2014, 06:24

... 1 ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Cotter Pin using Family Table Pro/ENGINEER Wildfire 2.0 Dr. Herli Surjanhata The following procedure ... cotter pin containing family table information – see above. The modeling of cotter pin is done using Sweep protrusion. CREATING A SWEEP PROTRUSION FOR COTTER PIN From Insert pull down ... button. Done/Return No...

Ngày tải lên: 22/12/2013, 11:17

... 1 ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Hexagon Bolts using Family Table – Pro/ENGINEER 2001 Dr. Herli Surjanhata Create a cylinder with dimensions ... datum plane as right reference for orientation of sketching plane. This is one-side protrusion using a circle as a section. 10 Select for example hex_bolt_050x2, then click Open button. ... 0.375”. Extrusion depth...

Ngày tải lên: 22/12/2013, 11:17

... bike_wrench.rwd Click OK. 1 ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN STRESS ANALYSIS Using Pro/MECHANICA Pro/ENGINEER Wildfire 2.0 Dr. Herli Surjanhata The bicycle wrench shown ... distributed load and boundary conditions. Check the convergence of your analysis. Step 1: Using Pro/ENGINEER, create a bicycle wrench as shown in the Figure below. Make sure the unit...

Ngày tải lên: 19/01/2014, 05:20

... [ Team LiB ] Using Digital Signatures When email is signed with a digital signature, it provides a level of proof that the person using the email address sent the message. ... issue a digital certificate for you to use. The certificate is valid only when you send email using the address that's included in the certificate. If you use several email addresses, ... Settings dialog...

Ngày tải lên: 21/01/2014, 02:20

... within the immediate location of the name (local scope). ■ Objects The objects in X.500 are defined using the organization (O), organizational unit (OU), and common name (CN) objects. This allows ... accounts. Active Directory is a logical representation of the objects in a network and organizes those objects using the organization (O), organizational unit (OU), and common name (CN) objec...

Ngày tải lên: 11/12/2013, 14:15

... 6 Module 2: Using Transact-SQL Querying Tools Using the osql Utility ! Starting the osql Command-line Utility ! Using the Interactive Mode ! Using the Script Execution Mode ! Using Extended ... Module 2: Using Transact-SQL Querying Tools 21 Review ! SQL Server Query Analyzer ! Using the Object Browser Tool in SQL Query Analyzer ! Using Templates in SQL Query Analyz...

Ngày tải lên: 11/12/2013, 14:15

... 1 ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Crankshaft Optimization Using Behavior Modeling Pro/ENGINEER Wildfire 2.0 Dr. Herli Surjanhata The engine designer ... model to its earlier state. 27 3 Step 1: Create a 1.25 in diameter cylinder using FRONT datum plane as sketching plane. The extrusion depth is 0.5 in. Note that the center

Ngày tải lên: 12/12/2013, 12:15

... follow. Programming Repeater Events by Using ItemCommand When you're using buttons, you can program the response for when the buttons are pressed by using the ItemCommand event. This event ... different controls-a Button and HyperLink-to display another list using the Repeater control. The second list will be displayed using the button on the same page as the first list. Th...

Ngày tải lên: 14/12/2013, 20:16

... Module 8: Using the SharePoint Portal Server Dashboard Site Exercise 2 Changing the Layout of a Dashboard In this exercise, you will change the layout of the Management dashboard by using the ... configure the proxy setting on the dashboard site using the proxycfg.exe utility. THIS PAGE INTENTIONALLY LEFT BLANK Module 8: Using the SharePoint Portal Server Dashbo...

Ngày tải lên: 21/12/2013, 06:15