bending about x-axis
1 RHS
C350L0 2
Finish 3
ADDITIONAL NOTES:
(A) THE ABOVE IS THE STANDARD GRADE FOR THE LISTED PRODUCTS. SEE THE FOLLOWING TABLE FOR THESE SECTIONS LISTED IN NON-STANDARD C450PLUS.
(B) SEE FOLLOWING TABLE FOR OTHER SIZES IN ATM’S LARGER RANGE OF C450PLUS PRODUCTS.
Australian Tube Mills A.B.N. 21 123 666 679. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3909 6600 Facsimile +61 7 3909 6660 E-mail info@austubemills.com Internet www.austubemills.com Notes:
1. REFER to the Australian Tube Mills PRODUCT AVAILABILITY GUIDE (PAG) for information on the availability of listed sections and associated finishes. The PAG can be found at www.austubemills.com.
2. Australian Tube Mills C450PLUS products satisfy both the strength and elongation requirements of AS/NZS 1163 Grades C350L0 (with the higher elongation requirements) and C450L0 (with the higher strength requirements of fy
= 450 MPa and fu = 500 MPa). See Section 2.4.2 for a detailed definition of C450PLUS.
3. Values of qMb based on _m = 1.0 (uniform moment over entire segment) in this Table.
4. Values to the left of those of the solid line are for segment lengths with full lateral restraint based on the listed FLR and qMb = qMsx.
5. FLR – segment length for Full Lateral Restraint (Clause 5.3.2.4 of AS 4100) with `m = -1.0.
6. For other moment distributions use the appropriate value of _m obtained from Clauses 5.6.1 or 5.6.2 of AS 4100 and use the minimum of _m qMb and qMsx given in this Table.
x x
d t
b
TABLE 5 . 3 - 2 ( 1 )
Rectangular Hollow Sections
C450PLUS ® – designed as AS/ NZS 1163 Grade C 450 L 0
DESIGN MOMENT CAPACITIES FOR MEMBERS WITHOUT FULL LATERAL RESTRAINT
bending about x-axis
Designation Mass
per m qMsx qVv Design Member Moment Capacities, qMb (kNm)
Effective Length (Le) in metres FLR
d b t
mm mm mm kg/m kNm kN 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 m
400 x 300 x 16.0 RHS 161 1110 2790 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 14.9
12.5 RHS 128 901 2220 901 901 901 901 901 901 901 901 901 901 901 901 901 901 15.1
10.0 RHS 104 649 1800 649 649 649 649 649 649 649 649 649 649 649 649 649 649 15.2
8.0 RHS 84.2 463 1450 463 463 463 463 463 463 463 463 463 463 463 463 463 463 15.4
400 x 200 x 16.0 RHS 136 866 2730 866 866 866 866 866 866 853 846 839 833 827 820 814 808 6.73
12.5 RHS 109 705 2170 705 705 705 705 705 705 695 689 684 679 674 669 664 659 6.87
10.0 RHS 88.4 581 1760 581 581 581 581 581 581 572 568 564 559 555 551 547 543 6.97
8.0 RHS 71.6 467 1420 467 467 467 467 467 467 467 458 454 451 448 444 441 438 7.04
350 x 250 x 16.0 RHS 136 807 2400 807 807 807 807 807 807 807 807 807 807 807 787 783 778 11.7
12.5 RHS 109 657 1920 657 657 657 657 657 657 657 657 657 657 657 640 637 634 11.9
10.0 RHS 88.4 533 1560 533 533 533 533 533 533 533 533 533 533 533 533 517 515 12.1
8.0 RHS 71.6 376 1260 376 376 376 376 376 376 376 376 376 376 376 376 368 367 12.2
300 x 200 x 16.0 RHS 111 548 2020 548 548 548 548 548 548 548 548 535 532 528 524 521 517 8.66
12.5 RHS 89.0 450 1620 450 450 450 450 450 450 450 450 440 437 434 431 428 425 8.85
10.0 RHS 72.7 373 1320 373 373 373 373 373 373 373 373 365 362 360 357 355 353 8.99
8.0 RHS 59.1 302 1070 302 302 302 302 302 302 302 302 302 294 292 290 288 286 9.10
6.0 RHS 45.0 192 813 192 192 192 192 192 192 192 192 192 189 188 187 186 185 9.20
250 x 150 x 16.0 RHS 85.5 338 1630 338 338 338 338 338 331 328 325 322 318 315 312 309 306 5.73
12.5 RHS 69.4 282 1320 282 282 282 282 282 276 274 271 269 266 264 261 259 256 5.90
10.0 RHS 57.0 236 1080 236 236 236 236 236 236 229 227 225 223 221 219 217 215 6.02
9.0 RHS 51.8 216 976 216 216 216 216 216 216 210 208 206 204 202 200 199 197 6.07
8.0 RHS 46.5 195 875 195 195 195 195 195 195 190 188 186 185 183 181 180 178 6.12
6.0 RHS 35.6 149 668 149 149 149 149 149 149 145 144 143 141 140 139 138 136 6.22
5.0 RHS 29.9 111 561 111 111 111 111 111 111 109 109 108 107 106 105 104 103 6.26
1 RHS
C450PLUS® 2
Finish 3
Australian Tube Mills A.B.N. 21 123 666 679. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3909 6600 Facsimile +61 7 3909 6660 E-mail info@austubemills.com Internet www.austubemills.com Notes:
1. REFER to the Australian Tube Mills PRODUCT AVAILABILITY GUIDE (PAG) for information on the availability of listed sections and associated finishes. The PAG can be found at www.austubemills.com.
2. Australian Tube Mills C450PLUS products satisfy both the strength and elongation requirements of AS/NZS 1163 Grades C350L0 (with the higher elongation requirements) and C450L0 (with the higher strength requirements of fy
= 450 MPa and fu = 500 MPa). See Section 2.4.2 for a detailed definition of C450PLUS.
3. Values of qMb based on _m = 1.0 (uniform moment over entire segment) in this Table.
4. Values to the left of those of the solid line are for segment lengths with full lateral restraint based on the listed FLR and qMb = qMsx.
5. FLR – segment length for Full Lateral Restraint (Clause 5.3.2.4 of AS 4100) with `m = -1.0.
6. For other moment distributions use the appropriate value of _m obtained from Clauses 5.6.1 or 5.6.2 of AS 4100 and use the minimum of _m qMb and qMsx given in this Table.
Designation Mass
per m qMsx qVv Design Member Moment Capacities, qMb (kNm)
Effective Length (Le) in metres FLR
d b t
mm mm mm kg/m kNm kN 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 m
200 x 100 x 10.0 RHS 41.3 129 833 129 129 129 126 124 122 120 118 116 115 113 111 109 108 3.29
9.0 RHS 37.7 119 758 119 119 119 116 114 113 111 109 107 106 104 103 101 99.5 3.33
8.0 RHS 33.9 108 681 108 108 108 106 104 103 101 99.4 97.9 96.4 95.0 93.5 92.1 90.7 3.37 6.0 RHS 26.2 85.1 522 85.1 85.1 85.1 83.2 82.0 80.7 79.5 78.3 77.1 76.0 74.8 73.7 72.6 71.5 3.44 5.0 RHS 22.1 72.6 440 72.6 72.6 72.6 71.0 69.9 68.9 67.8 66.8 65.8 64.8 63.9 62.9 62.0 61.1 3.48 4.0 RHS 17.9 58.4 355 58.4 58.4 58.4 57.2 56.4 55.5 54.7 53.9 53.1 52.4 51.6 50.8 50.1 49.4 3.52 152 x 76 x 6.0 RHS 19.4 47.0 389 47.0 47.0 46.0 45.0 44.1 43.3 42.4 41.5 40.7 39.9 39.1 38.4 37.6 36.9 2.56 5.0 RHS 16.4 40.4 329 40.4 40.4 39.5 38.8 38.0 37.2 36.5 35.8 35.1 34.4 33.7 33.1 32.4 31.8 2.60 150 x 100 x 10.0 RHS 33.4 80.7 611 80.7 80.7 80.7 80.7 78.2 77.1 76.1 75.0 74.0 73.0 72.0 71.0 70.0 69.1 4.22 9.0 RHS 30.6 74.8 559 74.8 74.8 74.8 74.8 72.6 71.6 70.6 69.6 68.7 67.7 66.8 65.9 65.0 64.1 4.28 8.0 RHS 27.7 68.5 504 68.5 68.5 68.5 68.5 66.5 65.6 64.7 63.8 62.9 62.1 61.2 60.4 59.6 58.8 4.33 6.0 RHS 21.4 54.4 389 54.4 54.4 54.4 54.4 52.8 52.1 51.4 50.7 50.0 49.4 48.7 48.0 47.4 46.8 4.44 5.0 RHS 18.2 46.6 329 46.6 46.6 46.6 46.6 45.3 44.7 44.1 43.5 42.9 42.3 41.8 41.2 40.6 40.1 4.49 4.0 RHS 14.8 37.8 267 37.8 37.8 37.8 37.8 36.7 36.2 35.7 35.3 34.8 34.4 33.9 33.5 33.0 32.6 4.55 150 x 50 x 6.0 RHS 16.7 36.9 374 36.9 35.4 34.1 32.8 31.5 30.3 29.2 28.1 27.1 26.1 25.1 24.2 23.4 22.6 1.12 5.0 RHS 14.2 31.9 316 31.9 30.7 29.5 28.4 27.4 26.3 25.4 24.4 23.6 22.7 21.9 21.1 20.4 19.7 1.14 4.0 RHS 11.6 26.5 257 26.5 25.5 24.6 23.7 22.8 21.9 21.2 20.4 19.7 19.0 18.3 17.7 17.1 16.5 1.17 3.0 RHS 8.96 20.8 195 20.8 20.1 19.3 18.6 17.9 17.3 16.7 16.1 15.5 15.0 14.4 13.9 13.5 13.0 1.19 2.5 RHS 7.53 17.6 164 17.6 17.0 16.4 15.8 15.2 14.7 14.1 13.6 13.2 12.7 12.3 11.8 11.5 11.1 1.21 2.0 RHS 6.07 12.8 132 12.8 12.5 12.1 11.7 11.3 10.9 10.6 10.2 9.92 9.61 9.31 9.03 8.75 8.49 1.22 127 x 51 x 6.0 RHS 14.7 27.9 315 27.9 27.1 26.1 25.3 24.4 23.6 22.8 22.0 21.3 20.6 20.0 19.3 18.7 18.1 1.35 5.0 RHS 12.5 24.3 267 24.3 23.6 22.8 22.0 21.3 20.6 19.9 19.2 18.6 18.0 17.5 16.9 16.4 15.9 1.38 3.5 RHS 9.07 18.1 192 18.1 17.6 17.0 16.4 15.9 15.4 14.9 14.4 13.9 13.5 13.1 12.7 12.3 11.9 1.43 125 x 75 x 6.0 RHS 16.7 34.1 317 34.1 34.1 33.5 32.8 32.2 31.6 31.0 30.4 29.9 29.3 28.8 28.2 27.7 27.2 2.96 5.0 RHS 14.2 29.5 269 29.5 29.5 29.5 28.4 27.9 27.3 26.8 26.3 25.8 25.4 24.9 24.4 24.0 23.6 3.01 4.0 RHS 11.6 24.4 219 24.4 24.4 24.4 23.5 23.1 22.7 22.2 21.8 21.4 21.0 20.7 20.3 19.9 19.5 3.06 3.0 RHS 8.96 18.8 167 18.8 18.8 18.8 18.2 17.9 17.5 17.2 16.9 16.6 16.3 16.0 15.7 15.4 15.1 3.11 2.5 RHS 7.53 14.1 140 14.1 14.1 14.1 13.7 13.5 13.3 13.0 12.8 12.6 12.4 12.2 12.0 11.8 11.7 3.14 2.0 RHS 6.07 10.0 113 10.0 10.0 10.0 9.86 9.72 9.58 9.45 9.32 9.18 9.05 8.93 8.80 8.68 8.56 3.16 102 x 76 x 6.0 RHS 14.7 25.1 255 25.1 25.1 25.1 24.3 23.9 23.5 23.1 22.7 22.3 21.9 21.5 21.2 20.8 20.4 3.63 5.0 RHS 12.5 21.7 218 21.7 21.7 21.7 21.1 20.7 20.4 20.0 19.7 19.3 19.0 18.7 18.4 18.1 17.8 3.69 3.5 RHS 9.07 16.1 157 16.1 16.1 16.1 15.7 15.4 15.1 14.9 14.6 14.4 14.1 13.9 13.7 13.4 13.2 3.78
x x
d t
b
TABLE 5 . 3 - 2 ( 2 )
Rectangular Hollow Sections
C450PLUS ® – designed as AS/ NZS 1163 Grade C 450 L 0
DESIGN MOMENT CAPACITIES FOR MEMBERS WITHOUT FULL LATERAL RESTRAINT
bending about x-axis
1 RHS
C450PLUS® 2
Finish 3
Australian Tube Mills A.B.N. 21 123 666 679. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3909 6600 Facsimile +61 7 3909 6660 E-mail info@austubemills.com Internet www.austubemills.com
NON-ST ANDARD GRADE
Notes:
1. REFER to the Australian Tube Mills PRODUCT AVAILABILITY GUIDE (PAG) for information on the availability of listed sections and associated finishes. The PAG can be found at www.austubemills.com.
2. Australian Tube Mills C450PLUS products satisfy both the strength and elongation requirements of AS/NZS 1163 Grades C350L0 (with the higher elongation requirements) and C450L0 (with the higher strength requirements of fy
= 450 MPa and fu = 500 MPa). See Section 2.4.2 for a detailed definition of C450PLUS.
3. Values of qMb based on _m = 1.0 (uniform moment over entire segment) in this Table.
4. Values to the left of those of the solid line are for segment lengths with full lateral restraint based on the listed FLR and qMb = qMsx.
5. FLR – segment length for Full Lateral Restraint (Clause 5.3.2.4 of AS 4100) with `m = -1.0.
6. For other moment distributions use the appropriate value of _m obtained from Clauses 5.6.1 or 5.6.2 of AS 4100 and use the minimum of _m qMb and qMsx given in this Table.
7. NOTE: Grey shaded listings are to C450L0 which is a non-standard grade - availability is subject to minimum order criteria. The standard grade for the shaded listings is AS/NZS 1163-C350L0. Please refer to earlier tables for design values associated with this as a standard grade. See the ATM PAG for further information on grades and availability.
Designation Mass
per m qMsx qVv Design Member Moment Capacities, qMb (kNm)
Effective Length (Le) in metres FLR
d b t
mm mm mm kg/m kNm kN 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.50 3.00 3.50 4.00 4.50 5.00 6.00 m
100 x 50 x 6.0 RHS 12.0 18.4 244 18.4 18.4 18.4 18.4 18.4 18.1 17.9 17.6 17.3 17.1 16.8 16.5 16.3 15.8 1.60 5.0 RHS 10.3 16.1 208 16.1 16.1 16.1 16.1 16.1 15.8 15.7 15.5 15.2 15.0 14.8 14.5 14.3 13.9 1.64 4.0 RHS 8.49 13.5 170 13.5 13.5 13.5 13.5 13.5 13.3 13.2 13.0 12.8 12.6 12.4 12.2 12.1 11.7 1.68 3.5 RHS 7.53 12.1 151 12.1 12.1 12.1 12.1 12.1 11.9 11.8 11.7 11.5 11.3 11.1 11.0 10.8 10.5 1.70 3.0 RHS 6.60 10.8 131 10.8 10.8 10.8 10.8 10.8 10.6 10.5 10.4 10.2 10.1 9.92 9.77 9.62 9.33 1.73 2.5 RHS 5.56 9.18 110 9.18 9.18 9.18 9.18 9.18 9.04 8.98 8.84 8.71 8.57 8.44 8.32 8.19 7.95 1.74 2.0 RHS 4.50 7.37 88.9 7.37 7.37 7.37 7.37 7.37 7.37 7.22 7.11 7.00 6.90 6.80 6.70 6.60 6.41 1.76 1.6 RHS 3.64 5.05 71.7 5.05 5.05 5.05 5.05 5.05 5.05 4.99 4.93 4.87 4.81 4.75 4.69 4.63 4.52 1.78 76 x 38 x 4.0 RHS 6.23 7.34 126 7.34 7.34 7.34 7.25 7.17 7.10 7.03 6.88 6.74 6.61 6.47 6.34 6.21 5.97 1.24 3.0 RHS 4.90 6.00 97.2 6.00 6.00 6.00 6.00 5.86 5.80 5.74 5.62 5.51 5.40 5.29 5.18 5.08 4.88 1.28 2.5 RHS 4.15 5.14 82.2 5.14 5.14 5.14 5.14 5.02 4.97 4.92 4.82 4.72 4.63 4.54 4.45 4.36 4.19 1.30 75 x 50 x 6.0 RHS 9.67 11.4 178 11.4 11.4 11.4 11.4 11.4 11.4 11.4 11.0 10.9 10.7 10.6 10.4 10.3 9.98 2.05 5.0 RHS 8.35 10.1 153 10.1 10.1 10.1 10.1 10.1 10.1 10.1 9.77 9.64 9.51 9.38 9.25 9.12 8.87 2.11 4.0 RHS 6.92 8.56 126 8.56 8.56 8.56 8.56 8.56 8.56 8.56 8.31 8.19 8.08 7.97 7.87 7.76 7.55 2.17 3.0 RHS 5.42 6.92 97.4 6.92 6.92 6.92 6.92 6.92 6.92 6.92 6.71 6.62 6.53 6.44 6.35 6.27 6.10 2.23 2.5 RHS 4.58 5.91 82.3 5.91 5.91 5.91 5.91 5.91 5.91 5.91 5.74 5.66 5.58 5.51 5.43 5.36 5.21 2.25 2.0 RHS 3.72 4.77 66.8 4.77 4.77 4.77 4.77 4.77 4.77 4.77 4.64 4.58 4.52 4.46 4.40 4.34 4.22 2.28 1.6 RHS 3.01 3.34 54.0 3.34 3.34 3.34 3.34 3.34 3.34 3.34 3.28 3.24 3.21 3.17 3.14 3.10 3.03 2.30 75 x 25 x 2.5 RHS 3.60 4.07 79.1 4.07 3.99 3.91 3.84 3.76 3.69 3.62 3.48 3.35 3.23 3.11 2.99 2.89 2.68 0.572
2.0 RHS 2.93 3.36 64.2 3.36 3.30 3.24 3.18 3.12 3.06 3.00 2.89 2.78 2.68 2.58 2.49 2.40 2.24 0.584 1.6 RHS 2.38 2.76 51.9 2.76 2.71 2.66 2.61 2.56 2.51 2.47 2.38 2.29 2.21 2.13 2.05 1.98 1.85 0.594 65 x 35 x 4.0 RHS 5.35 5.38 106 5.38 5.38 5.38 5.29 5.23 5.18 5.12 5.01 4.90 4.80 4.70 4.60 4.50 4.31 1.21
3.0 RHS 4.25 4.45 82.3 4.45 4.45 4.45 4.45 4.33 4.29 4.24 4.15 4.06 3.98 3.89 3.81 3.73 3.58 1.25 2.5 RHS 3.60 3.83 69.7 3.83 3.83 3.83 3.83 3.73 3.69 3.65 3.57 3.50 3.42 3.35 3.28 3.21 3.08 1.27 2.0 RHS 2.93 3.16 56.7 3.16 3.16 3.16 3.16 3.08 3.05 3.02 2.95 2.89 2.83 2.77 2.71 2.66 2.55 1.29 50 x 25 x 3.0 RHS 3.07 2.37 61.1 2.37 2.37 2.31 2.28 2.24 2.20 2.17 2.10 2.04 1.97 1.91 1.85 1.80 1.69 0.807
2.5 RHS 2.62 2.07 52.1 2.07 2.07 2.02 1.98 1.95 1.92 1.89 1.83 1.78 1.72 1.67 1.62 1.57 1.48 0.826 2.0 RHS 2.15 1.73 42.6 1.73 1.73 1.69 1.66 1.63 1.61 1.58 1.54 1.49 1.44 1.40 1.36 1.32 1.24 0.844 1.6 RHS 1.75 1.43 34.7 1.43 1.43 1.39 1.37 1.35 1.33 1.31 1.27 1.23 1.20 1.16 1.13 1.09 1.03 0.859 50 x 20 x 3.0 RHS 2.83 2.09 60.3 2.09 2.02 1.98 1.93 1.89 1.85 1.80 1.72 1.65 1.58 1.51 1.45 1.39 1.28 0.511 2.5 RHS 2.42 1.83 51.4 1.83 1.77 1.73 1.70 1.66 1.62 1.59 1.52 1.45 1.39 1.33 1.28 1.22 1.13 0.526 2.0 RHS 1.99 1.53 42.0 1.53 1.49 1.46 1.43 1.39 1.36 1.33 1.28 1.22 1.17 1.12 1.08 1.04 0.956 0.541 1.6 RHS 1.63 1.27 34.2 1.27 1.24 1.21 1.18 1.16 1.13 1.11 1.06 1.02 0.978 0.938 0.901 0.865 0.800 0.552
x x
d t
b
TABLE 5 . 3 - 2 ( 3 )
Rectangular Hollow Sections
C450PLUS ® – designed as AS/ NZS 1163 Grade C 450 L 0
DESIGN MOMENT CAPACITIES FOR MEMBERS WITHOUT FULL LATERAL RESTRAINT
bending about x-axis
1 RHS
C450PLUS® 2
Finish 3
Australian Tube Mills A.B.N. 21 123 666 679. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3909 6600 Facsimile +61 7 3909 6660 E-mail info@austubemills.com Internet www.austubemills.com
Blank Page
Australian Tube Mills A.B.N. 21 123 666 679. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3909 6600 Facsimile +61 7 3909 6660 E-mail info@austubemills.com Internet www.austubemills.com
Part 6