COMPONENTS
N*m (kgf*cm, ft.*lbf) : Specified torque
9.0 (92, 80 in.*lbf)
37 (377, 27)
37 (377, 27)
37 (377, 27)
REAR SEAT TRACK BRACKET COVER REAR SEAT ASSEMBLY RH
B120061E02
SE
N*m (kgf*cm, ft.*lbf) : Specified torque
21 (214, 16)
CENTER SEAT ASSEMBLY
CENTER SEAT HINGE COVER UPPER LH REAR SEAT CUSHION MOULDING RH
RECLINING COVER PROTECTOR LH
21 (214, 16)
B112112E01
SE
REAR SEAT COVER NO.1
REAR SEAT COVER NO.2 REAR SEAT CUSHION FRAME
SUB-ASSEMBLY
REAR SEAT CUSHION MOULDING REAR RH REAR SEAT CUSHION PAD
REAR SEAT HEADREST ASSEMBLY
REAR SEAT HEADREST SUPPORT
REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY
REAR SEAT LOCK STRIKER REAR SEATBACK LOCK STRIKER COVER
REAR SEATBACK LOCK STRIKER PROTECTOR SEPARATE TYPE REAR
SEAT CUSHION COVER SEPARATE TYPE REAR SEATBACK COVER
SEPARATE TYPE REAR SEATBACK PAD
REAR SEATBACK BOARD CARPET ASSEMBLY
REAR SEATBACK COVER REAR SEATBACK LOCK BEZEL UPPER
N*m (kgf*cm, ft.*lbf) : Specified torque Non-reusable part
42 (428, 31)
HOG RING
HOG RING
21 (214, 16)
21 (214, 16)
18 (184, 13) 33 (337, 24) 6.0 (61, 53 in.*lbf)
REAR SEAT BELT ASSEMBLY INNER
B112113E01
SE
FOLD SEAT CUSHION FRAME NO.2 REAR SEAT RECLINING CONTROL CABLE
REAR SEAT RECLINING COVER INNER RH REAR SEAT SHOULDER BELT COVER
REAR SEAT TRACK ADJUSTING HANDLE REAR SEAT TRACK ASSEMBLY INNER REAR SEAT TRACK
ASSEMBLY OUTER
REAR SEATBACK FRAME SUB-ASSEMBLY LOWER SEAT TRACK STOP PLATE
FOLD SEAT CUSHION FRAME NO.2
FOLD SEAT STOPPER BAND ASSEMBLY NO.1
REAR SEATBACK FRAME SUB-ASSEMBLY
RECLINING CONTROL LINK SUB-ASSEMBLY
N*m (kgf*cm, ft.*lbf) : Specified torque Non-reusable part
7.5 (77, 66 in.*lbf)
42 (428, 31)
42 (428, 31)
42 (428, 31)
42 (428, 31)
42 (428, 31) 80 (816, 59)
21 (214, 16)
18 (184, 13)
42 (428, 31) 42 (428, 31)
55 (561, 41)
E-RING
REAR CENTER SEAT OUTER BELT ASSEMBLY
B112114E01
SE
CENTER SEAT CUSHION COVER SUB-ASSEMBLY
CENTER SEAT CUSHION FRAME SUB-ASSEMBLY CENTER SEATBACK FRAME SUB-ASSEMBLY COAT HOOK CAP
REAR SEATBACK BOARD SUB-ASSEMBLY
REAR SEATBACK COVER
FOLD SEATBACK WIRE NO.2 CENTER SEATBACK COVER
REAR SEATBACK LOCK COVER
REAR SEATBACK ROD CONTROL LEVER OUTER
REAR SEAT CENTER ARMREST SUPPORT REAR SEAT
HEADREST ASSEMBLY CENTER
REAR SEAT HEADREST SUPPORT
REAR SEATBACK HINGE SUB-ASSEMBLY CENTER REAR SEATBACK LOCK SUB-ASSEMBLY
REAR SEATBACK MOULDING LH REAR SEATBACK
MOULDING RH
REAR SEATBACK HINGE SUB-ASSEMBLY CENTER
REAR SEAT ARMREST ASSEMBLY CENTER
RECLINING COVER PROTECTOR RH
REAR SEAT CUSHION PAD CENTER
N*m (kgf*cm, ft.*lbf) : Specified torque
21 (214, 16)
21 (214, 16)
21 (214, 16)
21 (214, 16)
21 (214, 16)
21 (214, 16)
NO.1 SEATBACK COVER
B112115E01
SE
REMOVAL
1. REMOVE REAR SEAT TRACK BRACKET COVER (a) Move the rear seat assembly RH to the rearmost
position by operating the rear seat track adjusting handle.
(b) Using a screwdriver, disengage the 4 claws.
HINT:
Tape the screwdriver tip before use.
(c) Pull the 2 rear seat track bracket covers toward the rear of the vehicle and remove them.
2. REMOVE REAR SEAT ASSEMBLY RH (a) Using a clip remover, remove the 5 clips.
(b) Remove the bolt and disconnect the floor anchor side of the fold seat stopper band assembly No.1.
(c) Move the rear seat assembly RH to the rearmost position by operating the rear seat track adjusting handle.
(d) Remove the 2 bolts on the front side.
(e) Move the rear seat assembly RH fully forward by operating the rear seat track adjusting handle.
(f) Remove the 3 bolts on the rear side.
(g) Move the rear seat assembly RH to the center position and adjust the seatback to the vertical position.
(h) Remove the rear seat assembly RH.
DISASSEMBLY
1. REMOVE RECLINING COVER PROTECTOR LH (a) Using a clip remover, remove the clip.
(b) Remove the screw.
(c) Remove the reclining cover protector LH as shown in the illustration.
2. REMOVE CENTER SEAT HINGE COVER UPPER LH (a) Remove the screw.
(b) Disengage the claw and remove the center seat hinge cover upper LH.
3. REMOVE CENTER SEAT ASSEMBLY
(a) Release the rubber band on the backside of the rear seatback board sub-assembly.
(b) Remove the hog rings.
(c) Remove the 4 bolts and center seat assembly.
4. REMOVE REAR SEAT HEADREST ASSEMBLY CENTER
B115707
B068192
SE
5. REMOVE REAR SEATBACK LOCK COVER (a) Disengage the 2 claws and remove the rear
seatback lock cover as shown in the illustration.
6. REMOVE REAR SEATBACK COVER
(a) Using a moulding remover, disengage the 8 claws and remove the 2 rear seatback covers.
7. REMOVE REAR SEATBACK BOARD SUB- ASSEMBLY
(a) Disengage the 4 clips and remove the rear seatback board sub-assembly.
8. REMOVE RECLINING COVER PROTECTOR RH (a) Using a clip remover, remove the clip.
(b) Remove the screw and reclining cover protector RH.
9. REMOVE CENTER SEAT CUSHION ASSEMBLY (a) Using a "torx" socket wrench (T45), remove the 2
"torx" bolts and center seat cushion assembly.
10. REMOVE CENTER SEAT CUSHION FRAME SUB- ASSEMBLY
(a) Disengage the hooks and remove the hog rings and center seat cushion frame sub-assembly.
11. REMOVE CENTER SEAT CUSHION COVER SUB- ASSEMBLY
(a) Remove the hog rings and center seat cushion cover sub-assembly.
12. REMOVE REAR SEAT CUSHION PAD CENTER
13. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY CENTER
(a) Using a "torx" socket wrench (T45), remove the 2
"torx" bolts and rear seatback hinge sub-assembly center.
14. REMOVE REAR SEATBACK MOULDING LH
(a) Remove the 3 screws and rear seatback moulding LH.
Claw
Claw
B070384E01
B115708
Clip
B068345E01
SE
15. REMOVE REAR SEATBACK MOULDING RH
(a) Remove the 3 screws and rear seatback moulding RH.
16. REMOVE REAR SEAT ARMREST ASSEMBLY CENTER
(a) Using a "torx" socket wrench (T45), remove the 2
"torx" bolts.
(b) Remove the nut, rear seat center armrest support, and rear seat armrest assembly center.
17. REMOVE REAR SEAT CENTER ARMREST SUPPORT 18. REMOVE REAR SEAT HEADREST SUPPORT
(a) Disengage the 2 claws and remove the rear seat headrest support (LH side).
19. REMOVE REAR SEAT HEADREST SUPPORT HINT:
Use the same procedures described for the LH side.
20. REMOVE NO.1 SEATBACK COVER (a) Remove the 2 screws.
(b) Using a moulding remover, disengage the 2 claws and remove the No.1 seatback cover.
21. REMOVE COAT HOOK CAP
(a) Using a screwdriver, disengage the 3 claws and remove the coat hook cap.
HINT:
Tape the screwdriver tip before use.
22. REMOVE NO.2 CENTER SEATBACK COVER (a) Remove the fold seatback cover.
(b) Remove the 3 screws and No.2 center seatback cover with the rear seatback rod control lever outer.
(c) Remove the No.2 center seatback cover from the rear seatback rod control lever outer.
23. REMOVE REAR SEATBACK ROD CONTROL LEVER OUTER
(a) Remove the rear seatback rod control lever outer from the fold seatback wire.
24. REMOVE FOLD SEATBACK WIRE
25. REMOVE REAR SEATBACK LOCK SUB-ASSEMBLY (a) Remove the 2 bolts and rear seatback lock sub-
assembly.
26. REMOVE CENTER SEATBACK FRAME SUB- ASSEMBLY
B060977
Claw
B112097E01
SE
27. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY
(a) Release the rubber band on the backside of the rear seatback board carpet assembly.
(b) Disengage the 4 clips and remove the rear seatback board carpet assembly.
28. REMOVE REAR SEAT CUSHION MOULDING RH (a) Remove the 2 screws.
(b) Disengage the claw and remove the rear seat cushion moulding RH as shown in the illustration.
29. REMOVE REAR SEAT CUSHION MOULDING REAR RH
(a) Remove the 2 screws.
(b) Disengage the 3 claws and remove the rear seat cushion moulding rear RH.
30. REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY
(a) Using a "torx" socket wrench (T45), remove the 2
"torx" bolts.
(b) Remove the hog rings.
(c) Remove the 2 bolts and separate type rear seat cushion assembly.
31. REMOVE REAR SEAT CUSHION FRAME SUB- ASSEMBLY
(a) Disengage the hooks and remove the hog rings and rear seat cushion frame sub-assembly.
32. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
(a) Remove the hog rings and separate type rear seat cushion cover.
33. REMOVE REAR SEAT CUSHION PAD
34. REMOVE REAR SEAT BELT ASSEMBLY INNER (See page SB-28)
35. REMOVE REAR SEAT HEADREST ASSEMBLY 36. REMOVE REAR SEATBACK LOCK STRIKER COVER
(a) Using a screwdriver, disengage the 2 claws and remove the rear seatback lock striker cover.
HINT:
Tape the screwdriver tip before use.
Clip
B112098E01
Claw
B112099E01
Claw
B112100E01
SE
37. REMOVE REAR SEAT LOCK CONTROL LEVER SUB- ASSEMBLY
(a) Remove the 2 screws.
(b) Disengage the rear seat reclining control cable and remove the rear seat lock control lever sub-
assembly.
38. REMOVE REAR SEAT HEADREST SUPPORT (a) Disengage the 2 claws and remove the rear seat
headrest support (LH side).
39. REMOVE REAR SEAT HEADREST SUPPORT HINT:
Use the same procedures described for the LH side.
40. REMOVE REAR SEATBACK LOCK BEZEL UPPER (a) Using a screwdriver, disengage the 4 claws and
remove the rear seatback lock bezel upper.
HINT:
Tape the screwdriver tip before use.
41. REMOVE REAR SEATBACK LOCK STRIKER PROTECTOR
(a) Remove the rear seatback lock striker protector.
42. REMOVE REAR SEAT LOCK STRIKER
(a) Using a "torx" socket wrench (T45), remove the rear seat lock striker.
43. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD
(a) Remove the bolt and disconnect the floor anchor side of the rear seat belt assembly outer center.
(b) Remove the 2 clips.
(c) Remove the bolt and rear seat belt hook.
(d) Disengage the hooks and remove the hog rings and separate type rear seatback cover with pad.
44. REMOVE SEPARATE TYPE REAR SEATBACK COVER
(a) Remove the hog rings and separate type rear seatback cover.
45. REMOVE SEPARATE TYPE REAR SEATBACK PAD 46. REMOVE REAR CENTER SEAT OUTER BELT
ASSEMBLY (See page SB-41)
B051234
B060977
Claw
B112101E01
B109595
SE
47. REMOVE REAR SEAT SHOULDER BELT COVER (a) Disengage the 2 claws and remove the rear seat
shoulder belt cover as shown in the illustration.
48. REMOVE FOLD SEAT STOPPER BAND ASSEMBLY NO.1
(a) Remove the bolt and fold seat stopper band assembly No.1.
49. REMOVE REAR SEAT RECLINING COVER INNER RH (a) Remove the screw.
(b) Disengage the claw and remove the rear seat reclining cover inner RH.
50. REMOVE REAR SEAT COVER NO.1
(a) Remove the screw and rear seat cover No.1.
51. REMOVE REAR SEAT COVER NO.2
(a) Remove the screw and rear seat cover No.2.
52. REMOVE REAR SEAT RECLINING CONTROL CABLE (a) Disconnect the 2 cables and remove the rear seat
reclining control cable.
53. REMOVE REAR SEATBACK FRAME SUB- ASSEMBLY
(a) Using a "torx" socket wrench (T45), remove the 2
"torx" bolts.
(b) Remove the 2 bolts and rear seatback frame sub- assembly.
54. REMOVE SEAT TRACK STOP PLATE (a) Remove the clamp.
(b) Disconnect the 2 seat track stop plate cables.
(c) Remove the 2 nuts and seat track stop plate.
55. REMOVE RECLINING CONTROL LINK SUB- ASSEMBLY
(a) Remove the 2 E-rings and 2 springs.
(b) Remove the bolt, nut and reclining control link sub- assembly.
56. REMOVE REAR SEATBACK FRAME SUB- ASSEMBLY LOWER
(a) Using a "torx" socket wrench (T45), remove the 3
"torx" bolts.
(b) Using a "torx" socket wrench (T55), remove the 2
"torx" bolts and rear seatback frame sub-assembly lower.
57. REMOVE FOLD SEAT CUSHION FRAME NO.2 (a) Remove the 4 nuts and 2 fold seat cushion frame
No.2.
Claw
B112102E01
SE
58. REMOVE REAR SEAT TRACK ADJUSTING HANDLE (a) Move the rear seat track assembly outer and rear
seat track assembly inner fully forward by operating the rear seat track adjusting handle.
(b) Using a hexagon wrench 1.5 mm (0.059 in.), push down the 2 handle stoppers as shown in the
illustration and remove the rear seat track adjusting handle.
59. REMOVE REAR SEAT TRACK ASSEMBLY OUTER 60. REMOVE REAR SEAT TRACK ASSEMBLY INNER Hexagon Wrench 1.5 mm (0.059 in.)
Hexagon Wrench
Adjusting Handle Handle Stopper
B112103E01
SE
REASSEMBLY
1. INSTALL REAR SEAT TRACK ASSEMBLY INNER 2. INSTALL REAR SEAT TRACK ASSEMBLY OUTER 3. INSTALL REAR SEAT TRACK ADJUSTING HANDLE 4. INSTALL FOLD SEAT CUSHION FRAME NO.2
(a) Install the fold seat cushion frame No.2 with the 4 nuts.
Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
5. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LOWER
(a) Temporarily install the rear seatback frame sub- assembly lower with the 5 "torx" bolts.
(b) Using a "torx" socket wrench (T55), tighten the 2
"torx" bolts.
Torque: 80 N*m (816 kgf*cm, 59 ft.*lbf)
(c) Using a "torx" socket wrench (T45), tighten the 3
"torx" bolts.
Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 6. INSTALL RECLINING CONTROL LINK SUB-
ASSEMBLY
(a) Install the reclining control link sub-assembly with the bolt and 4 nuts.
Torque: Bolt
21 N*m (214 kgf*cm, 16 ft.*lbf) Nut
42 N*m (428 kgf*cm, 31 ft.*lbf) (b) Install the 2 springs and the 2 new E-rings.
7. INSTALL SEAT TRACK STOP PLATE
(a) Install the seat track stop plate with the 2 nuts.
Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf) (b) Install the 2 seat track stop plate cables.
(c) Install the clamp.
8. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY (a) Temporarily install the rear seatback frame sub-
assembly with the 2 bolts and 2 "torx" bolts.
(b) Tighten the 2 bolts.
Torque: 55 N*m (561 kgf*cm, 41 ft.*lbf)
(c) Using a "torx" socket wrench (T45), tighten the 2
"torx" bolts.
Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
9. INSTALL REAR SEAT RECLINING CONTROL CABLE 10. INSTALL REAR SEAT COVER NO.2
11. INSTALL REAR SEAT COVER NO.1
12. INSTALL REAR SEAT RECLINING COVER INNER RH 13. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY
NO.1
14. INSTALL REAR SEAT SHOULDER BELT COVER
SE
15. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (See page SB-41)
16. INSTALL SEPARATE TYPE REAR SEATBACK PAD 17. INSTALL SEPARATE TYPE REAR SEATBACK
COVER
(a) Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with new hog rings.
NOTICE:
• Be careful not to damage the cover.
• When installing the hog rings, take care to minimize wrinkles as much as possible.
18. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD
(a) Install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly.
(b) Install the hook and new hog rings.
(c) Install the rear seat belt hook with the bolt.
Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) (d) Install the 2 clips.
(e) Install the floor anchor side of the rear seat belt assembly outer center with the bolt.
Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) (f) Check if the ELR locks.
NOTICE:
The check should be performed with the outer belt assembly installed.
(1) With the belt assembly installed, check that the belt locks when it is pulled out quickly.
19. INSTALL REAR SEAT LOCK STRIKER
(a) Using a "torx" socket wrench (T45), install the rear seat lock striker.
Torque: 33 N*m (337 kgf*cm, 24 ft.*lbf) 20. INSTALL REAR SEATBACK LOCK STRIKER
PROTECTOR
21. INSTALL REAR SEATBACK LOCK BEZEL UPPER 22. INSTALL REAR SEAT HEADREST SUPPORT 23. INSTALL REAR SEAT HEADREST SUPPORT
24. INSTALL REAR SEAT LOCK CONTROL LEVER SUB- ASSEMBLY
25. INSTALL REAR SEATBACK LOCK STRIKER COVER 26. INSTALL REAR SEAT HEADREST ASSEMBLY
27. INSTALL REAR SEAT BELT ASSEMBLY INNER (See page SB-28)
28. INSTALL REAR SEAT CUSHION PAD Hog Ring Pliers
B050126E02
B109595
SE
29. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER
(a) Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad with new hog rings.
NOTICE:
• Be careful not to damage the cover.
• When installing the hog rings, take care to minimize wrinkles as much as possible.
30. INSTALL REAR SEAT CUSHION FRAME SUB- ASSEMBLY
31. INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY
(a) Temporarily install the separate type rear seat cushion assembly with the 2 bolts and 2 "torx" bolts.
(b) Tighten the 2 bolts.
Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf) (c) Install new hog rings.
(d) Using a "torx" socket wrench (T45), tighten the 2
"torx" bolts.
Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf)
32. INSTALL REAR SEAT CUSHION MOULDING REAR RH
33. INSTALL REAR SEAT CUSHION MOULDING RH 34. INSTALL REAR SEATBACK BOARD CARPET
ASSEMBLY
35. INSTALL CENTER SEATBACK FRAME SUB- ASSEMBLY
36. INSTALL REAR SEATBACK LOCK SUB-ASSEMBLY (a) Install the rear seatback lock sub-assembly with the
2 bolts.
Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) 37. INSTALL FOLD SEATBACK WIRE
38. INSTALL REAR SEATBACK ROD CONTROL LEVER OUTER
39. INSTALL NO.2 CENTER SEATBACK COVER 40. INSTALL COAT HOOK CAP
41. INSTALL NO.1 SEATBACK COVER
42. INSTALL REAR SEAT HEADREST SUPPORT 43. INSTALL REAR SEAT HEADREST SUPPORT
44. INSTALL REAR SEAT CENTER ARMREST SUPPORT 45. INSTALL REAR SEAT ARMREST ASSEMBLY
CENTER
(a) Temporarily install the rear seat armrest assembly center with the nut and rear seat center armrest support.
Hog Ring Pliers
B050126E02
SE
(b) Using a "torx" socket wrench (T45), install the rear seat armrest assembly center with the 2 "torx" bolts.
Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) 46. INSTALL REAR SEATBACK MOULDING RH 47. INSTALL REAR SEATBACK MOULDING LH
48. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY CENTER
(a) Using a "torx" socket wrench (T45), install the 2 rear seatback hinge sub-assembly centers with the 2
"torx" bolts.
Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) 49. INSTALL REAR SEAT CUSHION PAD CENTER 50. INSTALL CENTER SEAT CUSHION COVER SUB-
ASSEMBLY
51. INSTALL CENTER SEAT CUSHION FRAME SUB- ASSEMBLY
52. INSTALL CENTER SEAT CUSHION ASSEMBLY (a) Using a "torx" socket wrench (T45), install the
center seat cushion assembly with the 2 "torx" bolts.
Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) 53. INSTALL RECLINING COVER PROTECTOR RH 54. INSTALL REAR SEATBACK BOARD SUB-
ASSEMBLY
55. INSTALL REAR SEATBACK COVER
56. INSTALL REAR SEATBACK LOCK COVER 57. INSTALL REAR SEAT HEADREST ASSEMBLY
CENTER
58. INSTALL CENTER SEAT ASSEMBLY
(a) Install the center seat assembly with the 4 bolts.
Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) (b) Install new hog rings.
59. INSTALL CENTER SEAT HINGE COVER UPPER LH 60. INSTALL RECLINING COVER PROTECTOR LH
SE
INSTALLATION
1. INSTALL REAR SEAT ASSEMBLY RH
(a) Place the rear seat assembly RH in the vehicle and align the adjuster pin with the hole on the vehicle side.
(b) Move the rear seat assembly RH to the rearmost position by operating the rear seat track adjusting handle.
NOTICE:
Check that the seat is locked.
(c) Temporarily install the front side of the rear seat assembly RH with the 2 bolts.
(d) Recline the separate rear seatback forward by operating the rear seat lock control lever sub- assembly.
(e) Move the rear seat assembly RH fully forward.
NOTICE:
Check that the seat is locked.
(f) Temporarily install the rear side of the rear seat assembly RH with the 3 bolts.
(g) Return the separate rear seatback to the upright position.
(h) Move the rear seat assembly RH to the rearmost position by operating the rear seat track adjusting handle.
NOTICE:
Check that the seat is locked.
(i) Fully tighten the 2 bolts on the front side of the rear seat assembly RH in the order of the inner side bolt and then the outer side bolt.
Torque: 37 N*m (377 kgf*cm, 27 ft.*lbf) (j) Recline the separate rear seatback forward by
operating the rear seat lock control lever sub- assembly.
(k) Move the rear seat assembly RH fully forward.
NOTICE:
Check that the seat is locked.
(l) Fully tighten the 3 bolts on the rear side of the rear seat assembly RH in the order of the inner rear side bolt, the inner front side bolt, and then the outer side bolt.
Torque: 37 N*m (377 kgf*cm, 27 ft.*lbf)
(m) Return the separate rear seatback to the upright position.
(n) Move the rear seat assembly RH to the rearmost position by operating the rear seat track adjusting handle.
NOTICE:
Check that the seat is locked.
(o) Install the floor anchor side of the fold seat stopper band assembly No.1 with the bolt.
Torque: 9.0 N*m (92 kgf*cm, 80 in.*lbf) (p) Install the 5 clips.
SE
2. INSTALL REAR SEAT TRACK BRACKET COVER 3. INSPECT SLIDE ADJUSTER LOCK
(a) Check that the left and right adjusters lock simultaneously when sliding the seat.
(b) If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.
SE