toyota và con đường vượt qua khủng hoảng

... Springs Check the squargness of the valve springs will a steal square and surface plate, Turn ‘the spring around slowly and observe the space between the top of the spring and ‘the square, Replace ... 1 2ì (7) Check valve concentrivity Liphtly coat seat with peussian blue, linstall valve and rotate, If blue appears 360" around face, velve ste and fom are concantrin If nat, replace ... DISASSEMBLY INSPECTION & REPAIR ASSEMBLY CYLINDER BLOCK Includes: Cylinder Block, Piston and Connecting Rod Piston Ring Crank pin and Bearing, Crankshaft and Bearing Trang 5 18R ENGINE

Ngày tải lên: 28/03/2014, 09:22

... (1) Push the connector deep inside (2) Pinch portion A (3) Pull out the connector (c) Disconnect the vapor pressure sensor connector (d) Disconnect the wire harness clamp (e) Disconnect the purge ... (398 kgf*cm, 29 ft.*lbf) (b) Connect the purge line hose to the charcoal canister (c) Connect the wire harness clamp (d) Connect the vapor pressure sensor connector (e) Connect the charcoal canister ... Disconnect the fuel tank vent hose from the charcoal canister (1) Push the connector deep inside (2) Pinch portion A (3) Pull out the connector Pinch A A Pinch A Push A A132954E01 (b) Disconnect

Ngày tải lên: 23/05/2014, 16:27

... the connector before disconnecting them. Clean them if necessary. (3) Disconnect the connector from the pipe by hand. (4) When the connector and the pipe are stuck, push in and pull on the connector ... the connecting part of the pipe. (2) Match the axis of the connector with the axis of the pipe, and push into the connector until the connector makes a "click" sound. If the connection ... to disconnect the connector by hand. (3) If the connector and pipe are stuck, hold the fuel pipe by hand and push and pull on the connector. Pull the two pipes apart to separate the connector.

Ngày tải lên: 23/05/2014, 16:34

... Terminal 50 Terminal 30 A133510E01 Condition Specified condition at 11.5 V 90 A or less A058586E04 Terminal C Below 1 Ω Terminal 50 A079725E08 Tester connection Specified condition Terminal 50 - Terminal ... Ω Segment A058372E04 Tester connection Specified condition Segment - Segment Below 1 Ω Commutator Coil Core 10 kΩ or Higher A058373E04 Tester connection Specified condition Commutator - Armature ... of the following tests within 5 seconds to prevent the coil from burning out. (a) Perform pull-in test: (1) Disconnect the lead wire from terminal C. (2) Connect the battery to the magnetic

Ngày tải lên: 23/05/2014, 16:53

... procedure, connect an ammeter and voltmeter as shown in the illustration. (1) Disconnect the wire from terminal B of the generator and connect it to the negative (-) lead of the ammeter. (2) Connect ... terminal cap (b) Remove the nut and disconnect the wire harness from terminal B (c) Disconnect the generator connector from the generator... the cylinder block (h) Disconnect the wire harness clamp and ... SYSTEM CH–1 CH CHARGING SYSTEM PRECAUTION 1. Check that the battery cables are connected to the correct terminals. 2. Disconnect the battery cables when the battery is given a quick charge. 3. Do

Ngày tải lên: 23/05/2014, 16:54

... (1) Push the connector deep inside (2) Pinch portion A (3) Pull out the connector (c) Disconnect the vapor pressure sensor connector (d) Disconnect the wire harness clamp (e) Disconnect the purge ... (398 kgf*cm, 29 ft.*lbf) (b) Connect the purge line hose to the charcoal canister (c) Connect the wire harness clamp (d) Connect the vapor pressure sensor connector (e) Connect the charcoal canister ... Disconnect the fuel tank vent hose from the charcoal canister (1) Push the connector deep inside (2) Pinch portion A (3) Pull out the connector Pinch A A Pinch A Push A A132954E01 (b) Disconnect

Ngày tải lên: 23/05/2014, 16:55

... player uses a laser pickup to read digital signals recorded on CDs. By converting the digital signals to analog, music and other content can be played. CAUTION: Do not look directly at the laser ... changed. The conventional car audio system is being integrated with multi-media interfaces similar to those in navigation systems. At the same time, customers are demanding higher quality from ... AV–9 AV (b) "Bluetooth" is a new wireless connection technology that uses the 2.4 GHz frequency band. This makes it possible to connect a cellular phone ("Bluetooth" compatible

Ngày tải lên: 24/05/2014, 13:15

... speed is stored and the vehicle is controlled at a constant speed. CRUISE CONTROL – CRUISE CONTROL SYSTEM CC–7 CC (e) TAP-UP CONTROL When tapping up the cruise control main switch to + (ACCEL)/RES ... due to the idle speed control, etc. (c) TAP-DOWN CONTROL When tapping down the cruise control main switch to - (COAST)/SET (for approximately 0.6 seconds) while the cruise control system is in ... REPLACE 14 CONFIRMATION TEST END E107085 E107086 [...]... Shift lever is except D or 4 position - CRUISE CONTROL Cruise control system active condition / ON or OFF ON: Cruise control

Ngày tải lên: 24/05/2014, 13:28

... UPPER CONSOLE PANEL (See page IP-25) 5. REMOVE UPPER CONSOLE REAR PANEL SUB- ASSEMBLY (See page IP-26) 6. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (a) Remove the 2 clips and disconnect ... TRANSMISSION CONTROL CABLE ASSEMBLY (a) Connect the control cable to the shift lever retainer. NOTICE: • The projecting part of the cable outer should face upward when the shift cable is connected. ... point is connected. • The clip should be installed in the direction as shown in the illustration. 3. INSTALL UPPER CONSOLE REAR PANEL SUB- ASSEMBLY (See page IP-53) 4. INSTALL UPPER CONSOLE PANEL

Ngày tải lên: 24/05/2014, 13:31

... (a) Disconnect the connector. (b) Remove the 3 bolts. (c) Disconnect the hood lock control cable. (d) Remove the hood lock assembly. 10. REMOVE HOOD LOCK CONTROL LEVER SUB- ASSEMBLY (a) Disconnect ... support (c) Connect the clamps as shown in the illustration 2 B136826 INSTALL HOOD LOCK CONTROL LEVER SUBASSEMBLY (a) Install the hood lock control lever and connect the hood lock control cable ... ASSEMBLY (a) Disconnect the hood lock control cable and remove the hood lock control lever. 11. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (a) Using a screwdriver, disconnect the clamps shown in the

Ngày tải lên: 24/05/2014, 13:35

... Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. (e) Disconnect each connector, and then remove ... the 8 screws, 2 clips, 2 radiator grille protectors and bolt. (d) Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration. HINT: Use the same procedures for ... screwdriver tip before use B146331 (c) Remove the 6 screws ET B140154 (d) Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration HINT: Use the same procedures for

Ngày tải lên: 24/05/2014, 13:37

... Part Name Part # Toyota Genuine Motor oil 5W–30 00279–1QT5W Toyota Genuine Motor oil 10W–30 00279–1QT30 Ethylene–Glycol Antifreeze Good brand of ethylene–glycol based antifreeze Toyota Long Life ... Differential 94–95 96–98 99–02 03–05 ALL 94–98 Ethyl- ene–Glycol Antifreeze ALL 99–03 Toyota Long Life coolant ALL 04–05 Toyota Su- per Long Life coolant API GL–5 75W–90, Castle V160 or Sequential M/T ... –1– 1: –35 to 50F 2: 0 to 150F FLUID SPECS MY ’94 – ’05 Toyota Scion Vehicle Model Engine Type Engine Oil And Year Model Coolant Manual Trans. Automatic

Ngày tải lên: 24/05/2014, 13:37

... BOX CARPET CONSOLE BOX POCKET CONSOLE BOX ASSEMBLY B137289E01 INSTRUMENT PANEL – REAR CONSOLE BOX IP–61 CONSOLE COMPARTMENT DOOR SUB-ASSEMBLY IP for Manual Air Conditioning System: REAR CONSOLE ... UPPER CONSOLE PANEL SUB-ASSEMBLY (for TMC Made) (a) Connect each connector B134001 (b) Engage the claws (c) Install the upper console panel sub-assembly with the screws 26 INSTALL UPPER CONSOLE ... Install the console box assembly with the bolts or or or B134003E02 20 INSTALL CONSOLE BOX CARPET (a) Install the console box carpet 21 INSTALL CONSOLE BOX POCKET (a) Install the console box

Ngày tải lên: 24/05/2014, 13:42

... Before performing electrical work, disconnect the battery negative (-) terminal in order to prevent a short in the system. (b) When disconnecting and reconnecting the battery cable, turn the ... for 0.8 second or more. Outside temperature display Displays the outside temperature in accordance with the ambient temperature signal from the A/C control amplifier. Average fuel consumption ... until the following conditions are met and 5 seconds have passed with Multi-information display: Trip Meter Reset Knob Master Caution Indicator... RS-228 3 Wire Harness or Connector - 4 Combination

Ngày tải lên: 24/05/2014, 13:44

... Heater: (1) Disconnect the connector and remove the outer rear view mirror glass B146020 3 INSTALL OUTER REAR VIEW MIRROR. .. Made) (a) with Mirror Heater: (1) Connect the connector B136869 ... Mirror (LH) I3 Outer Rear View Mirror (RH) H2 B140703E01 MIRROR – POWER MIRROR CONTROL SYSTEM MI–3 MI F16 Heater Control Panel Assembly E38 RDFG RR DEF Relay from A/C No. 2 fuse Engine Room R/B, ... 1B1K 1J A/C Amplifier Assembly B137069E01 MI–4 MIRROR – POWER MIRROR CONTROL SYSTEM MI PROBLEM SYMPTOMS TABLE Power Mirror Control System Symptom Suspected area See page Power mirrors cannot be

Ngày tải lên: 24/05/2014, 13:44

... contains a resistor that is necessary to enable communication... Lower Stack version is displayed HINT: This function is controlled by the built-in display ECU 4 E 120068 NS HANDSFREE VOICE QUALITY ... to read digital signals recorded on a compact disc (CD). By converting the digital signals to analog, it can play music and other content. NOTICE: • Do not disassemble any part of the CD player. ... Voice Quality Set" from the "'Bluetooth' Handsfree Check Menu" screen NS–29 NAVIGATION – NAVIGATION SYSTEM (b) Check the handsfree voice level *1 *2 E 120069 E01 Screen Description: Display Contents

Ngày tải lên: 24/05/2014, 13:46

... BRAKE LEVER PB–9 PB CONSOLE BOX ASSEMBLY CONSOLE BOX ASSEMBLY CONSOLE BOX CARPET CONSOLE BOX POCKET NO. 1 CONSOLE BOX INSERT FRONT NO. 2 CONSOLE BOX INSERT FRONT for Manual Air Conditioning System: ... CONSOLE BOX ASSEMBLY CONSOLE BOX CARPET CONSOLE BOX POCKET NO. 1 CONSOLE BOX INSERT FRONT NO. 2 CONSOLE BOX INSERT FRONT for Manual Air Conditioning System: for Automatic Air Conditioning System: ... SUB-ASSEMBLY UPPER CONSOLE PANEL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY FLOOR CARPET BRACKET LH FLOOR CARPET BRACKET RH C133456E01 PB–8 PARKING BRAKE – PARKING BRAKE LEVER PB CONSOLE BOX ASSEMBLY CONSOLE

Ngày tải lên: 24/05/2014, 13:49

... PREPARATION – 2AZ-FE ENGINE CONTROL SYSTEM PP–1 PP PREPARATIONPREPARATION 2AZ-FE ENGINE CONTROL SYSTEM RECOMMENDED TOOLS 09082-00040 TOYOTA Electrical Tester (09083-00150) Test ... ENGINE CONTROL SYSTEM PP EQUIPMENT Ohmmeter Radiator cap tester Service Wire Harness Torque wrench PP–2 PREPARATION – 2GR-FE ENGINE CONTROL SYSTEM PP PREPARATIONPREPARATION 2GR-FE ENGINE CONTROL ... 2AZ-FE ENGINE MECHANICAL PP SSM Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent Toyota Genuine Seal Packing 1282B, Three Bond 1282B or Equivalent Toyota Genuine Adhesive 1324,

Ngày tải lên: 24/05/2014, 13:49

... Description Condition Specified Condition F3-3 (IG) - Body ground Power supply Ignition switch OFF → ON (IG) Below 1 V → 10 to 14 V Terminal No. (Symbols) Terminal Description Condition Specified Condition ... (for Manual Seat) (a) for Driver seat: (1) Disconnect the connectors and disengage the 4 clamps (b) for Passenger seat: (1) Disconnect the connector and disengage the 3 clamps SB SB–16 SEAT ... Power Seat) (a) for Driver seat: (1) Disconnect the connectors and... B131996 SB 10 DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY (a) Remove the nut and disconnect the shoulder anchor of the front

Ngày tải lên: 24/05/2014, 13:50

... the CLOSE or UP switch is held down, continue to hold the switch for another 10 seconds or more to return the sliding roof control ECU to an uninitialized condition. Then perform the initialization ... No.) Wiring Color Terminal Description Condition Specified Condition R1 B050671E35 Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition B (R1-1) - E (R1-2) B - W-B ... roof control ECU) 2 Roof console box assembly (Sliding roof control switch) 3 Wire harness RF-22 B2344 Position Failure 1 Sliding roof drive gear sub-assembly (Sliding roof control

Ngày tải lên: 24/05/2014, 13:50