... RÁP M.TÍNHCÀI WINDOW 98CÀI WIN2000, XPPARTION MAGIC Sửa chữa ổ CD ROM Nội dung : Sửachữa các bệnh thường gặp của ổ CD Rom . SỬACHỮA CÁC BỆNH THƯỜNG GẶP CỦA Ổ CD -ROM Bệnh 1 : Cửa ñĩa ... TÍNH1/20/200http://www.hocnghe.com.vn/Phancung/Phancung.asp TIỆN ÍCH GHOSTLAN - INTERNETDowload G.TrìnhPHẦN S / CHỮALấy ñĩa ra khi ñĩa bị kẹt Tháo vỏ ổ ñĩa ra ñể có thể quan sát bộ cơ và bộ phận môtơ ra vào...
... Master hay Slaver thông việc cắm Jumper ở vị trí nào trên sơ đồ Jumper Pins (thông thường có hướngdẫn trên lưng ổ đĩa)Ổ đĩa cứngỔ PowerJumperỔ Data1.5.4 Ổ CD-ROM-R/W-DVD1.5.5 Ổ đĩa Mềm...
... flange, and gasket must be secure.Never operate the device without a microwaveenergy absorbing load attached.Never look into an open waveguide or antennawhile the device is energized.GasketANTENNACOOLING ... repaired:(a) The interlock monitor switch is connectedcorrectly and firmly.(b) The magnetron gasket is properly positioned and mounted.(c) The waveguide and the oven cavity are intact. (no ... andcavity. Never operate the magnetron unless it isproperly installed.• Be sure that the magnetron gasket is properlyinstalled around the dome of the tube wheneverinstalling the magnetron.Unlike...
... Exhaust gas temperature sensor• Exhaust gas leaks in TOYOTA D-CAT• Mass air flow meter• Engine ECUP2031*1Exhaust Gas Temperature Sensor Circuit(Bank 1 sensor 2)• Open or short in exhaust gas ... Circuit HighP0544*1Exhaust Gas Temperature Sensor Circuit(Bank 1 Sensor 1)• Open or short in exhaust gas temperature sensor (on up stream)circuit• Exhaust gas temperature sensor (on up ... (on down stream)• Exhaust gas temperature sensor (on down stream)• Engine ECUP2032*1Exhaust Gas Temperature Sensor Circuit Low(Bank 1 sensor 2)P2033*1Exhaust Gas Temperature Sensor Circuit...
... bolts, nozzle leakage pipe andtwelve gaskets.8. REMOVE INJECTION NOZZLES(1PZ and 1HZ)(a) (1PZ)Using SST, remove the five injection nozzles, seatsand gaskets.SST 09268-64010(b) (1HZ)Using ... ten bolts, seal washers, intake manifoldand five gaskets.(c) (1 HZ and 1HD-T)Remove the twelve bolts, seal washers, intake mani-fold and six gaskets.6. REMOVE WATER OUTLET(a) (1HD-T)Disconnect ... Remove the two nuts, water outlet and gasket.7. REMOVE NOZZLE LEAKAGE PIPE(1PZand1HZ)(a) (1PZ)Remove the five union nuts, nozzle leakage pipe andfive gaskets.(b) (1HZ)Remove the six union...
... installation surface.(b) Apply clean engine oil to the gasket of a new oil filter.(c) Lightly screw the oil filter into place, and tighten it until thegasket contacts the seat.(d) Using SST, tighten ... tighten it an additional 3/4 turn.SST 09228 0650154. INSTALL CYLINDER HEAD GASKET(a) Place a new cylinder head gasket on the cylinder blocksurface with the Lot No. stamp upward.NOTICE:S ... Place the cylinder head quietly in order not todamagethe gasket with the bottom part of the head.(b) Apply seal packing to the cylinder head gasket as shownin the illustration.Seal packing:Part...
... đèn công suất không chập => thì sửa như Trường hợp 2 ở dưới .=> Nếu có một hoặc nhiều đèn công suất bị chập => thì sửa như Trường hợp 3 ở dưới* Sửa chữa: - Trường hợp 1: Có điện áp 5V ... dù đã có nguồn 300V đầu vào, bạn cần kiểm tra kỹ các linh kiện sau của nguồn cấp trước : Hướng dẫnsửachữa bộ nguồn ATX 14-11-2008 | lqv77 | 91 phản hồi »1. Nguyên lý hoạt động của bộ nguồn ... xem có không ? ( đo giữ dây tím và dây đen )=> Nếu có 5V STB ( trên dây mầu tím ) => thì sửachữa như Trường hợp 1 ở dưới- Nếu đo dây tím không có điện áp 5V, bạn cần tháo vỉ nguồn ra ngoài...