ethernet networking and data encapsulation

CCNARS studyguide toddlammle

... Collision and Broadcast Domains 34 35 Review Questions Chapter Ethernet Networking and Data Encapsulation 41 Ethernet Networks in Review 42 Collision Domain 43 Broadcast Domain 44 CSMA/CD 45 Half- and ... Hands-on Labs 953 Hands-on Lab 7.1: Configuring PPP Encapsulation and Authentication 953 Hands-on Lab 7.2: Configuring and Monitoring HDLC 955 Hands-on Lab 7.3: Configuring Frame Relay 956 and ... 648 Hands-on Labs 648 Hands-on Lab 1.1: Verifying STP and Finding Your Root Bridge 649 Hands-on Lab 1.2: Configuring and Verifying Your Root Bridge 651 Hands-on Lab 1.3: Configuring PortFast and...

Ngày tải lên: 14/11/2014, 15:44

1,2K 740 0

CCNA Lab - Securing Networks With Cisco Routers And Switches

... Security Commands Command Description arp timeout seconds This command is used to configure how long an entry remains in the ARP cache To restore the default value, use the no form of this command show ... ACS 4.0 ̈ Student laptops ̈ Pod devices Command List The table describes the commands that are used in this activity Cisco Secure ACS Commands Command Description N/A — Job Aids These job aids ... Choose Allow MD-5 Step Under Credential Validation Databases, choose ACS Internal Database and click the Right Arrow button to move it to the Selected Databases column Step Click Apply + Restart Activity...

Ngày tải lên: 23/10/2015, 18:10

214 790 0

Tài liệu cisco migration_Mobile Access Router and Mesh Networks pdf

... Fast Ethernet 0/0 Fast Ethernet FE0X Fast Ethernet 2/0 Fast Ethernet FE1X Fast Ethernet 2/1 Fast Ethernet Internal WMIC Fast Ethernet 2/2 Fast Ethernet Internal WMIC Fast Ethernet 2/3 Fast Ethernet ... VLAN database using the vlan database command Configure VLAN and VLAN interface VLAN is used for 2.4 GHz WMIC2 (W2) acting as AP and VLAN is for 4.9GHz WMIC (W3) Configure FA2/0, FA2/1 and FA2/3 ... unicast key is used to exchange unicast data between the root device and authenticated device, and the broadcast key is used to exchange multicast and broadcast data between them When you enable EAP...

Ngày tải lên: 24/01/2014, 10:20

36 725 0

Tài liệu giảng dạy CCNA - module 04 chapter 14-LAN Switching Review and Configuring Cisco 2950 LAN Switches

... 00E0.1E5D.AE2F Ethernet 0/2 Dynamic All 00D0.588F.B604 FastEthernet 0/26 Dynamic All 00E0.1E5D.AE2B FastEthernet 0/26 Dynamic All 0090.273B.87A4 FastEthernet 0/26 Dynamic All 00D0.588F.B600 FastEthernet ... FastEthernet vlan  To remove this entry use the no form of the command:  Switch(config)#no mac-address-table static interface FastEthernet ... autonegotiate and the attached port is set to full duplex with no autonegotiation capability causing the switch port to be in half-duplex mode 22 FCS and Late Collision Errors wg_sw_a#show interfaces Ethernet...

Ngày tải lên: 12/08/2015, 09:19

27 357 0

Cấu hình Cisco Router

... R1#(config-if)ip unnumbered ethernet slot/port Không gán ip trực tiếp cho serial port mà “mïn” tạm ip ethernet port R1#(config-if)ip unnumbered ethernet0 /0 R1#(config-if)bandwidth bandwidth Gán bandwidth (tốc ... 4.2.1 Cấu hình ethernet port serial Trước tiên ta cần phải đònh đòa xác lập số thông số cho ethernet port serial • Ethernet port Bảng sau trình bày số lệnh cần thiết để cấu hình ethernet port ... interface Ethernet0 no ip address ipx network 100 encapsulation SAP ipx network 101 encapsulation NOVELLETHER secondary ! interface Serial0 description Leased Line to Boston no ip address ** encapsulation...

Ngày tải lên: 30/08/2012, 09:54

94 995 9