activity configuring frame relay point to point subinterfaces

... in a full-mesh Frame Relay network. An Adtran Atlas550 Frame Relay emulator is used to simulate the switch /Frame Relay cloud. Background/Preparation Cable a network similar to the one in the ... PVC. Step 8 Show the Frame Relay maps a. Look at the frame relay maps by typing the command show frame- relay map at the privileged exec mode prompt: Amsterdam#show frame- relay map b. What ... Amsterdam(config-if)#encapsulation frame- relay ietf Amsterdam(config-if) #frame- relay lmi-type ansi b. Use a description field to store relevant information, such as the circuit number in case a line fault has to be...

Ngày tải lên: 11/12/2013, 14:15

... in a full-mesh Frame Relay network. Background/Preparation An Adtran Atlas550 Frame Relay emulator is used to simulate the Frame Relay switch/cloud. Cable a network similar to the one in the ... PVC. Step 8 Show the Frame Relay maps a. Look at the frame relay maps by typing the command show frame- relay map at the privileged EXEC mode prompt: Amsterdam#show frame- relay map b. What ... Amsterdam(config-if)#encapsulation frame- relay ietf Amsterdam(config-if) #frame- relay lmi-type ansi b. Use a description field to store relevant information, such as the circuit number in case a line fault has to be...

Ngày tải lên: 11/12/2013, 14:15

... in a full-mesh Frame Relay network. An Adtran Atlas550 Frame Relay emulator is used to simulate the switch /Frame Relay cloud. Background/Preparation Cable a network similar to the one in the ... PVC. Step 8 Show the Frame Relay maps a. Look at the frame relay maps by typing the command show frame- relay map at the privileged exec mode prompt: Amsterdam#show frame- relay map b. What ... Berlin(config-router)#network 192.168.6.0 Step 7 Verifying Frame Relay PVC a. On the Amsterdam router, issue the command show frame- relay pvc: Amsterdam#show frame- relay pvc b. How many active local PVCs...

Ngày tải lên: 18/01/2014, 05:20

... in a full-mesh Frame Relay network. Background/Preparation An Adtran Atlas550 Frame Relay emulator is used to simulate the Frame Relay switch/cloud. Cable a network similar to the one in the ... PVC. Step 8 Show the Frame Relay maps a. Look at the frame relay maps by typing the command show frame- relay map at the privileged EXEC mode prompt: Amsterdam#show frame- relay map b. What ... Amsterdam(config-if)#encapsulation frame- relay ietf Amsterdam(config-if) #frame- relay lmi-type ansi b. Use a description field to store relevant information, such as the circuit number in case a line fault has to be...

Ngày tải lên: 18/01/2014, 05:20

... protocol. â 2002, Cisco Systems, Inc. All rights reserved. ICND v2.07-4 ã Supports only single-protocol environments HDLC Frame Format ã Uses a proprietary data field to support multiprotocol ... encapsulating data on synchronous serial data links. ã PPP encapsulates network layer protocol information over point- to -point links. ã Configurable aspects of PPP include methods of authentication, ... rights reserved. ICND v2.0—7-2© 2002, Cisco Systems, Inc. All rights reserved. 2 Configuring Serial Point- to -Point Encapsulation © 2002, Cisco Systems, Inc. All rights reserved. ICND v2.0—7-7 Layering...

Ngày tải lên: 06/03/2014, 15:20

... lab. Step 2 Configuring the serial interface a. In Frame Relay, the customer router is considered the DTE device. In order to configure the serial interface the Layer 2 Frame Relay frame type ... Cork(config-if)#end Step 3 Verifying the Frame Relay configuration a. To verify the configuration, use the show interface commands, related to Frame Relay. To view the serial interface configuration ... format of the Frame Relay management protocol must be configured. To configure the Local Management Interface (LMI) type, use the following commands: Cork(config-if) #frame- relay lmi-type...

Ngày tải lên: 11/12/2013, 14:15

... Step 7 Showing Frame- Relay map a. To view the Layer 2 to Layer 3 mapping, use the show frame- relay map command at the privileged exec mode prompt: Washington#show frame- relay map b. ... Step 2 Configuring the serial interface First, define the Frame Relay frame type to be used on this link. To configure the encapsulation type, use the command encapsulation frame- relay ietf. ... Frame Relay switch in this configuration and consequently no Frame Relay DCE: Washington#configure terminal Washington(config-if)#interface serial 0 Washington(config-if)#encapsulation frame- relay...

Ngày tải lên: 11/12/2013, 14:15

... lab. Step 2 Configuring the serial interface a. In Frame Relay, the customer router is considered the DTE device. In order to configure the serial interface the Layer 2 Frame Relay frame type ... Cork(config-if)#end Step 3 Verifying the Frame Relay configuration a. To verify the configuration, use the show interface commands, related to Frame Relay. To view the serial interface configuration ... format of the Frame Relay management protocol must be configured. To configure the Local Management Interface (LMI) type, use the following commands: Cork(config-if) #frame- relay lmi-type...

Ngày tải lên: 18/01/2014, 05:20

... Step 7 Showing Frame- Relay map a. To view the Layer 2 to Layer 3 mapping, use the show frame- relay map command at the privileged exec mode prompt: Washington#show frame- relay map b. ... Dublin(config-if)#description PVC to Washington, DLCI 102, Circuit #DASS465866 Contact Pat White (091-6543211) Step 6 Verifying Frame Relay PVC a. On the Washington router, type the command show frame- relay pvc: ... Objective ã Configure two routers back -to- back as a Frame Relay permanent virtual circuit (PVC). This will be done manually, in the absence of a Frame Relay switch, and therefore no Local Management...

Ngày tải lên: 18/01/2014, 05:20

... Thuật to n Lempel-Ziv (LZS) (RFC 1974 ) cung cấp cơ chế nén và giải nén nhanh dữ liệu. Thuật to n này được sử dụng trong cơ chế nén STAC trong PPP, ISDN và Frame Relay. Point to Point Protocol ... hai cơ chế chứng thực Password Authentication Protocol (PAP) hay Challenge Handshake Authentication Protocol (CHAP). ã Network Control Protocol (NCP): NCP lm nhim v thit lập, điều chỉnh cấu ... code xác định cho nó, và giá trị mã này được đặt trong trường protocol của gói tin NCP, một số giá trị ví dụ như sau: Code Protocol 8021 IP 8029 AT 8025 XNS, Vines 8027 DECnet 8031 Bridge...

Ngày tải lên: 18/01/2014, 20:20

... Control Plane Dynamic Routing IPsec Control Plane Dynamic Crypto Map DPD Static Crypto Map DPD Headend Branch Dynamic Routing GRE Control Plane Point- to -Point GRE Point- to -Point GRE 8 Point- to -Point GRE over IPsec Design Guide OL-9023-01 Preface ... configured to allow the tunnel traffic bi-directionally. The crypto headend must be accessible to the branch router. 2-21 Point- to -Point GRE over IPsec Design Guide OL-9023-01 Chapter 2 Point- to -Point ... provided in Chapter 2, Point- to -Point GRE over IPsec Design and Implementation.” 2-19 Point- to -Point GRE over IPsec Design Guide OL-9023-01 Chapter 2 Point- to -Point GRE over IPsec Design...

Ngày tải lên: 24/01/2014, 10:20

... reserved. 2 Configuring Frame Relay © 2002, Cisco Systems, Inc. All rights reserved. ICND v2.0—8-6 Configuring Subinterfaces ã Point- to -point Subinterfaces act like leased lines. Each point- to -point ... you want to control routed broadcast traffic, you must define the address -to- DLCI table statically. ã You can configure Frame Relay subinterfaces in either point- to -point or multipoint mode. ã After ... about Frame Relay DLCIs and the LMI Router#show frame- relay lmi [type number] ã Displays LMI statistics Router#show frame- relay map ã Displays the current Frame Relay map entries Router#show frame- relay...

Ngày tải lên: 06/03/2014, 15:20

Ngày tải lên: 21/06/2014, 02:20

Ngày tải lên: 28/06/2014, 03:20

Ngày tải lên: 06/07/2014, 08:55

Ngày tải lên: 01/08/2014, 07:20

Ngày tải lên: 02/08/2014, 00:21

Ngày tải lên: 11/08/2014, 05:20

Ngày tải lên: 14/08/2014, 12:20

... Use show frame- relay pvc and show frame- relay map to troubleshoot connectivity problems. Rebooting the Frame Relay switch might also solve connectivity issues. SanJose3#show frame- relay pvc ... Singapore(config-if) #frame- relay map ip 192.168.192.2 17 broadcast Singapore(config-if)#ip ospf network point- to- multipoint Verify Frame Relay operation with a ping from each router to the other ... configuration includes frame- relay map commands, which are typically used with Frame Relay subinterfaces. These commands are needed here so that you can configure Frame Relay to handle broadcast...

Ngày tải lên: 19/10/2013, 03:15