ac motor speed control circuit tutorial

Ngày tải lên: 18/12/2013, 22:06

... root-locus domain. Mechatronics Kevin Craig DC Motor / Tachometer Closed-Loop Speed Control System 24 Mechatronics DC Motor / Tachometer Closed-Loop Speed Control System 1. Introduction This ... Mechatronics Kevin Craig DC Motor / Tachometer Closed-Loop Speed Control System 21 Table 1. Specifications of the Honeywell 22VM51-020-5 DC Motor with Tachometer Motor Characteristics Units Values ... Mechatronics Kevin Craig DC Motor / Tachometer Closed-Loop Speed Control System 17 Mechatronics Kevin Craig DC Motor / Tachometer Closed-Loop Speed Control System 29 9. Testing of the...

Ngày tải lên: 25/01/2014, 13:20

Ngày tải lên: 12/09/2013, 22:38

Ngày tải lên: 17/12/2013, 14:15

Ngày tải lên: 28/12/2013, 22:07

... . 1 Speed Control TM ô SPC Gas Springs, cushioned 2486.12. FIBRO SPC Gas Springs Speed Control TM ô are designed to reduce or eliminate the sheet metal retainer bounce back which is ... caused by the increased return travel speed in high speed presses (link drive presses). SPC Gas Springs feature an integral return travel delay which reduces the speed of the gas spring to 0.4 m/s ... a soft arrival for the sheet metal retainer. Benefits of the Speed Control TM ô SPC Gas Springs, cushioned:  Prevents bounce back of sheet metal retainer.  Increased productivity through...

Ngày tải lên: 22/01/2014, 02:20

... or nonsinusoidal back emf waveforms. Machines with sinusoidal back emfs may be controlled so as to achieve nearly con- stant torque; however, machines with a nonsinusoidal back emf may be less ... nominal operating speed of 200 rad/s (mechanical). 542 PERMANENT-MAGNET AC MOTOR DRIVES The structure of the control algorithms determines the type of permanent-magnet ac motor drive, of which ... structure of the controls Figure 14.1-1. Permanent-magnet ac motor drive. Electrical System Command Signal Power Converter Control PM AM Mechanical System Sensors 566 PERMANENT-MAGNET AC MOTOR DRIVES ...

Ngày tải lên: 16/02/2014, 18:54

Ngày tải lên: 16/03/2014, 12:20

... As a result, the speed of a closed-loop control system (that is, without loss of surface) is determined by the time constant 0 0 i G K τ . Feedback speed, the speed of the actuator, is limited ... control [1, 2]. Let us find the maximum scan speed without loss of surface. The transient response of the loop control to a capacitive displacement sensor output (if the high-frequency pole ... line traces of the calibration grating with the step height equal to 25 nm. At a constant speed of 30 àm/s (a), with a dynamic control (b), and with a dynamic control and at a variable speed...

Ngày tải lên: 21/06/2014, 17:20

... frequency 1/τ q .is 20 (Hz) because reaction torque Advances in Motor Torque Control 16 Sub motor controller Sub motor Rack & Pinion Torque Sensor Main motor Electric Signal Line Planetary ... torque- control motor capable of achieving faster and easier root canal preparation. Speed and maximum torque levels are preselectable and constantly controlled by the TCM III control unit. Speed ... electric motors without torque control and the electric torque control motors. (Fig 4) Fig. 4. Torque control motor. Theoretically, the torque control hand pieces (motors) take into consideration...

Ngày tải lên: 29/06/2014, 09:20

... (5 each) 5 x 2 EEM41 Three-phase asynchronous machines Asynchronous motor Experiment procedure: z Start the "ActiveDrive/ActiveASMA" software z Select "Automatic speed control& quot; ... asynchronous machines Asynchronous motor Circuit diagram "Connection & starting" (delta connection) 11 EEM41 Three-phase asynchronous machines Asynchronous motor Set-up "Reactive ... Three-phase asynchronous machines Asynchronous motor Experiment procedure: z Start the "ActiveDrive/ActiveASMA" software z Select "Automatic speed control& quot; operating mode...

Ngày tải lên: 13/07/2014, 00:20

Ngày tải lên: 19/08/2014, 19:33

... detect the outputs of an induction motor, we can use this motor controller to control an induction machine. ã TMS320F243 DSP controller. This is manufactured by the Texas Instruments Company ... nominal speed. However, outside the rated speed operation, the flux has to be decreased like an inverse function of speed. By weakening the rotor flux, the induction machine can reach speeds ... to develop a control strategy for the DSP controller that controls the torque production within the induction machine. However, there is no great emphasis placed on precise torque control. ...

Ngày tải lên: 27/10/2013, 23:15

... redefined by the user. A matrix is written with a square bracket ‘[]’ with spaces separating adjacent columns and semicolons separating adjacent rows. For example, consider the following assignments ... %Define a time vector with 201 equally-spaced points from 0 to 5 s. w = logspace(-1,3,201); %Define a radian frequency vector with 201 logarithmically-spaced 14 < less than <= less than ... saved in an m-file. To create an m-file using emacs, you can type from Athena prompt athena% emacs filename.m & or from within MATLAB >> ! emacs filename.m & Note that ‘!’ allows execution...

Ngày tải lên: 12/12/2013, 07:15

Ngày tải lên: 13/12/2013, 00:56

Ngày tải lên: 13/12/2013, 03:40

Ngày tải lên: 17/12/2013, 18:06

Ngày tải lên: 18/12/2013, 09:10

Ngày tải lên: 25/12/2013, 05:17

... R 2 I C I C V H- V H+ B I I Printed Circuit Board AN894 DS00894A-page 10  2003 Microchip Technology Inc. BACK EMF CONTROL METHOD The back electro-magnetic-force (EMF) or sensorless motor control method obtains the speed ... signal-conditioning circuitry into a single package. In most motor control systems, several sensors are used to provide feedback information on the motor. These sensors are used in the control loop ... Management Input Microcontroller Driver Motor Feedback Torque Speed Direction Current Sensor Sensors * Speed * Shaft Position * Rotation Direction PICmicro đ Motor Control Sensor Feedback Circuits ...

Ngày tải lên: 03/01/2014, 18:55