Đang tải... (xem toàn văn)
Solution Manual for Renewable and Efficient electric Power System REEPS2 (Gilbert Masters)Solution Manual for Renewable and Efficient electric Power System REEPS2 (Gilbert Masters)Solution Manual for Renewable and Efficient electric Power System REEPS2 (Gilbert Masters)Solution Manual for Renewable and Efficient electric Power System REEPS2 (Gilbert Masters)Solution Manual for Renewable and Efficient electric Power System REEPS2 (Gilbert Masters)Solution Manual for Renewable and Efficient electric Power System REEPS2 (Gilbert Masters)
lOMoARcPSD|2935381 REEPS2 Chapter Problems SOLUTIONS CHAPTER 2: PROBLEM SOLUTIONS 2.1 A source is connected through a switch to a load that is either a resistor, a capacitor or an inductor At t = 0, the switch is closed and current delivered to the load results in the voltage shown below What is the circuit element and what is its magnitude? V" ?" Source" Figure P2.1 SOLN: The relationship follows the form i = C dv/dt, so it is a CAPACITOR C= i 0.1 = = 0.01F dv dt 100 10 2.2 A voltage source produces the square wave shown below The load, which is either an ideal resistor, capacitor or inductor, draws current as shown below Figure P2.2 a Is the “Load” a resistor, a capacitor or an inductor ? di dv fits the graph, while v = Ri and i = C not, is an INDUCTOR dt dt Sketch the power delivered to the load versus time SOLN: Since v = L b SOLN: c What is the average power delivered to the load? Gmasters Pg Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems SOLUTIONS From the graph of power, average power = SOLN: 2.3 A source supplies voltage v(volts) = 10 cos ω t to a 5-Ω resistive load i=? v = 10 cos ω t R = 5Ω Source' Figure P2.3 a Write an expression for the current (amps) delivered to the load SOLN: b Write an expression for the power delivered to the load p = vi = 10 cos ω t ⋅ 2 cos ω t = 40 cos (ω t ) SOLN: c v 10 cos ω t = = 2 cos ω t R i= Sketch a graph of power versus time What is the average power (W) delivered to the load? SOLN: From the sketch, easy to see average value of cos2x = 1/2 1" cos$x" 0" $1" 1" 1/2" 0" cos2$x" ( ) ( ) Pavg = avg 40 cos ω t = 40avg cos ω t = 40x = 20W 2.4 Suppose your toaster has 14-gage wire inside and, to simplify the analysis, suppose we approximate the normal 60-Hz sinusoidal current flowing through that wire with a square wave carrying ± 10A Using a drift-velocity calculation, find the average back-and-forth distance those electrons travel d$=$?$ 10A$ i! 60$cycles/s$ +/%$10A$ t! 14$ga$ %10A$ Figure P2.4 SOLN: From Table 2.3, 14-ga wire has diameter 0.0641 in, so its cross-sectional area is A= π π D = ( 0.0641 in x 2.54 cm/in x 10 -2 m/cm ) = 2.08x10 −6 m 4 From (2.2) the average drift velocity (m/s) is Gmasters Pg 2 Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems Drift = SOLUTIONS i 10 coulomb/s = 28 nqA 8.48x10 elec/m x 1.602x10 -19 coul/elec x 2.08x10 -6 m = 0.000354 m/s = 3.54 x 10 −4 m/s In one half of a 60-Hz cycle the electrons go one way, then turn around and go back Distance = 3.54x10 −4 m/s x s ⋅ = 2.94x10 −6 m 60 cycle So, literally, the electrons never leave the toaster as asserted in the text 2.5 As is the case for all metals, the resistance of copper wire increases with temperature in an approximately linear manner that can be expressed as RT2 = RT1 [1+ α ( T2 − T1 )] where α = 0.00393/oC How hot copper wires have to get to cause their resistance to increase by 10% over their value at 20oC? SOLN: RT2 = RT1 [1+ α ( T2 − T1 )] RT o = 1.10 = + 0.00393/ oC ⋅ (T2 − 20) C RT1 2.6 T2 = 20 + 25.4 = 45.4 o C = 114 o F A 52-gallon electric water heater is designed to deliver 4800 watts to an electricresistance heating element in the tank when it is supplied with 240V (it doesn’t matter if this is ac or dc) 240V 4800W 52 gal Figure P2.6 a What is the resistance of the heating element? SOLN: R= V 240 = = 12 Ω P 4800 b How many watts would be delivered if the element is supplied with 208V instead of 240V? SOLN: V 208 P= = = 3605 W = 3.605 kW R 12 Gmasters Pg Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems c SOLUTIONS Neglecting any losses from the tank, how long would it take for 4800 W to heat the 52 gallons of water from 60oF to 120oF? The conversion between kilowatts of electricity and Btu/hr of heat is given by 3412 Btu/h = kW Also, one Btu heats lb of water by 1oF and gallon of water weighs 8.34 lbs SOLN: Heat needed = 52 gal x 8.34 lb/gal x Btu/lbo F x (120 − 60)o F = 26,020 Btu 26,020 Btu ΔT( hr) = = 1.59 hr 4.8 kW x 3412 Btu/kWhr d If electricity costs $0.12/kWh, what is the cost of a 15-gallon, 110oF shower if the coldwater supply temperature is 60oF? SOLN: 15 g x 8.34 lb/g x 1Btu/lb o F x (110-60) o F x $0.12/kWh Cost = 3412 Btu/kWh = $0.22 2.7 Suppose an automobile battery is modeled as an ideal 12-V battery in series with an internal resistance of 0.01 Ω as shown in (a) below Starter& a Figure P2.7 What current will be delivered when the battery powers a 0.03-Ω starter motor, as in (b)? What will the battery output voltage be? SOLN: a While driving the starter motor: I= V 12 = = 300A R 0.01+ 0.03 Vb = 0.03 Ω x 300 A = 9V b or with the voltage divider Vb = 12⋅ 0.03 = 9V 0.01 + 0.01 Compare the power delivered by the battery to the starter with the power lost in the battery's internal resistance What percentage is lost in the internal resistance SOLN: Delivered to the starter p ( delivered ) = i R = ( 300 ) x0.03 = 2736W p(battery loss) = ( 300 ) x0.01 = 900W Gmasters Pg Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems SOLUTIONS To recharge the battery, what voltage must be applied to the battery in order to deliver a 20A charging current as in (c)? c While being charged with 20A: SOLN: Vb = 12V + 0.01Ω x 20A = 12.2V d Suppose the battery needs another 480 Wh of energy to be fully charged, which could be achieved with a quick-charge of 80A for 0.5 hour (80A x 0.5hr x 12V = 480 Wh) or a trickle charge of 10A for hours Compare the Wh of energy lost in the internal resistance of the battery for each charging scheme SOLN: e @ 80A I2R x Δt loss = (80)2 x 0.01 x 0.5 hr = 32 Wh (32/480 = 6.7%) @ 10A I2R x Δt loss = (10)2 x 0.01 x hr (4/480 = 0.9%) Automobile batteries are often rated in terms of their cold-cranking amperes (CCA), which is the number of amps they can provide for 30 seconds at 0oF while maintaining an output voltage of at least 1.2V per cell (7.2V for a 12-V battery) What would be the CCA for the above battery (assuming the idealized 12-V source still holds)? SOLN: CCA = 2.8 = Wh ΔV (12 − 7.2 )V = = 480A R 0.01Ω A photovoltaic (PV) system is delivering 15A of current through 12-gage wire to a battery 80 feet away AWG#12## 15A# +# +# 12#V# 80#)# PVs# Ba2ery# Figure P2.8 a Find the voltage drop in the wires SOLN: From Table 2.3, 12-ga wire has 0.1588 Ω per 100-ft With 160-ft of wire (to-andfrom) the voltage drop would be ΔV = RI = 15A x 160 ft x(0.1588Ω /100ft) = 15A x 0.254Ω = 3.81V b What fraction of the power delivered by the PVs is lost in the connecting wires? SOLN: Power delivered by the PVs = I V = 15A x (12+3.81)V = 237W Power lost in wires = I2R = (15)2 x 0.254 = 57.2W % loss in wire = c 57.2W = 24% 237W Using Table 2.3 as a guide, what wire size would be needed to keep wire losses to less than 5% of the PV power output (assume the PVs will continue to keep the current at 15A, which, by the way is realistic)? Gmasters Pg Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems SOLUTIONS SOLN: ΔV# R##5%#loss# 12#+#ΔV# PV# 12V# 5%PV-power = R-power 15# 15A# 0.05x15x (12 + 15R ) = 15 R 0.6 + 0.75R = 15R 0.6 = 0.0421Ω /160 ft R= 14.25 100 x0.0421 = 0.0263Ω /100 ft R≤ 160 Since 4-ga wire has 0.0249 Ω/100 ft, it will just be good enough 2.9 Consider the problem of using a low-voltage system to power your little cabin Suppose a 12-V system powers a pair of 60-W lightbulbs (wired in parallel) The distance between these loads and the battery pack is 50 ft 50#'# 60)W#ea.# @#12#V# 12#V# Figure P2.9 a Since these bulbs are designed to use 60 W at 12 V, what would be the (filament) resistance of each bulb? SOLN: b I ( each bulb ) = V 12V = = 5A both bulbs 10A R 2.4Ω Of the gages shown in Table 2.3, what gage wire should be used if it is the minimum size that will carry the current? SOLN: d V (12 ) so R = = = 2.4Ω ea P 60 What would be the current drawn by two such bulbs if each receives a full 12 V? SOLN: c V2 P= R 14-ga wire will handle 15A, so that is adequate Find the equivalent resistance of the two bulbs plus the wire resistance to and from the battery Both lamps are turned on (in this and subsequent parts) SOLN: First draw the circuit The wire resistance is 0.2525 Ω/100ft, so Gmasters Pg Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems SOLUTIONS 0.2525/2&Ω& 12&V& 2.4&Ω&&&&&&&&&&&&&&&&&&&&&&2.4&Ω& 0.2525/2&Ω& The two lamps in parallel have a total of 1.2 Ω, which added to the 100-ft of wire gives RTotal = 1.2 + 0.2525 = 1.4525 Ω e Find the current delivered by the battery with both lamps turned on SOLN: f I= Find the power delivered by the battery SOLN: g V 12 = = 8.26A R 0.2525 + 1.2 PBattery = VI =12V x 8.26A = 99.1 W Find the power lost in the connecting wires in watts and as a percentage of battery power Pwire = I R = ( 8.26 ) x0.2525 = 17.2 W SOLN: Wire loss = h 17.2 W = 17.4% 99.1 W Find the power delivered to the lamps in watts and as a percentage of their rated power SOLN: PLamps = PBattery − PWires = 99.1 − 17.2 = 81.9W % of full power to lamps = 81.9 = 68% 60 + 60 … so they're going to be much dimmer than full brightness ! 2.10 Suppose the system in Problem 2.9 is redesigned to work at 24 volts with 12-gage wire and two 24-V 60-W bulbs What percentage of the battery power is now lost in the wires? SOLN: 100-ft of 12-ga wire has 0.1588 Ω of resistance Each bulb has R = V2/P = (24)2/60 = 9.6 Ω, so two in parallel have 9.6/2 = 4.8 Ω The circuit is now 0.1588#Ω# vbulbs 24#V# 4.8#Ω# 4.8 ⎞ ⎛ Vbulbs = 24 ⎜ = 23.231V ⎝ 4.8 + 0.1588 ⎟⎠ Power lost in the wires Gmasters Pg Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems Pwire 2 ΔV ) 24 − 23.231) ( ( = = 0.1588 Rwire SOLUTIONS = 3.72 W Power from the battery and % losses V2 24 = = 116.16 W Rtot 0.1588 + 4.8 3.72 = = 0.032 = 3.2% 116.16 Pbattery = Ploss Pbattery 2.11 Suppose the lighting system in a building draws 20 A (ac or dc; it doesn't matter) and the lamps are, on the average, 100 ft from the electrical panel Table 2.3 suggests that 12-ga wire meets code, but you want to consider the financial merits of wiring the circuit with bigger 10-ga wire Suppose the lights are on 2500 hours per year and electricity costs $0.10 per kWh 100#'# Romex Panel 15# 20A# Lights Neutral Ground Hot Figure P2.11 a Find the energy savings per year (kWhr/yr) that would result from using 10 ga instead of 12 ga wire SOLN: 12 ga wire @ 0.1588 Ω/100 ft x 200 ft = 0.3176 Ω Pwire (12 ga) = I2 R = 202 x 0.3176 = 127.04 watts 10 ga wire @ 0.0999 Ω/100 ft x 200 ft = 0.1998 Ω Pwire (10 ga) = I2 R = 202 x 0.1998 = 79.92 watts Energy savings = (127.04 – 79.92)W x 2.500 khr/yr = 117.8 kWh/yr b Suppose 12-ga Romex (2 conductors, each 100-ft long, plus a ground wire that carries no current, in a tough insulating sheath) costs $50 per 100 ft and 10 ga costs $70 per 100 ft What would be the “simple payback” period (1st cost divided by annual savings) when utility electricity costs $0.10/kWh SOLN: Payback = Extra cost $70-$50 $20 = = =1.7 yr Annual savings 117.8 kWh/yr x $0.10/kWh $14.14/yr c An effective way to evaluate energy efficiency projects is by calculating the annual cost associated with conservation and dividing it by the annual energy saved This is the Cost of Conserved Energy (CCE ) and is described more carefully in Appendix A CCE is defined as follows Gmasters Pg Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems SOLUTIONS annual cost of saved electricity ( $/yr ) ΔP ⋅ CRF ( i, n ) = annual electricity saved (kWh/yr) kWh/yr where ΔP is the extra cost of the conservation feature (heavier duty wire in this case), and CRF is the capital recovery factor (which means your annual loan payment on $1 borrowed for n years at interest rate i CCE = What would be the “cost of conserved energy” CCE (¢/kWh) if the building (and wiring) is being paid for with a 7%, 20-yr loan with CRF = 0.0944/yr How does that compare with the cost of electricity that you don’t have to purchase from the utility at 10¢/kWhr? SOLN: 0.07(1 + 0.07)20 = 0.0944 / yr (1 + 0.07)20 − ΔP ⋅ CRF $ ( 70-50 ) ⋅ 0.0944/yr CCE = = ΔkWh/yr 117.8kWh/yr =$0.016/kWh = 1.6¢/kWh way cheaper than 10¢ With CRF(7%, 20yr) = 2.12 Thevenin's theorem says that the output of any circuit consisting of resistors and ideal voltage sources can be modeled as a voltage source in series with a resistance Suppose the Thevenin equivalent of a circuit consists of a 12-V source in series with a 6-Ω resistance Figure P2.12 a What is output voltage with an infinite load so no current flows (called the open-circuit voltage, VOC)? SOLN: b What is the output current when the terminals are shorted together (called the short-circuit current, ISC) SOLN: c VOC = 12 V I SC = 12V = 2A 6Ω Write an equation for the output current I as a function of the output voltage Vout Draw a graph of I versus Vout (as the load changes) SOLN: Gmasters Pg Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems 10 Vout = 12 − 6I ISC = 2A! I= I! V 12 − Vout = − out 6 VOUT% d SOLUTIONS VOC = 12V! Using the equation found in (c), determine the location (I, V) on the graph at which the maximum power will be delivered to a load This is called the maximum power point and you'll see it a lot in the chapters on photovoltaics Show that point on your I-V graph from part (c) SOLN: P = IV = I (12 − 6I ) = 12I − 6I Max Power Point MPP : dP = 12 − 12I = dI so I max = 1A and Vmax = 12 - 6x1= 6V ISC = 2A! MPP#at#1A,#6V# I! VOUT% VOC = 12V! d What load resistance will result in the circuit delivering maximum power to the load? How much power would that be? SOLN: The maximum power point occurs when the circuit delivers A at 6V to a load R= V 6V = = 6Ω I 1A Pmax = I R = (1) x6 = W 2.13 When circuits involve a source and a load, the same current flows through each one and the same voltage appears across both A graphical solution can therefore be obtained by simply plotting the current-voltage (I-V) relationship for the source onto the same axes that the I-V relationship for the load is plotted, and then finding the crossover point where both are satisfied simultaneously This is an especially powerful technique when the relationships are nonlinear as will be the case for the analysis of photovoltaic systems Gmasters Pg 10 Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems 11 SOLUTIONS Consider the following I-V curve for a source delivering power to a load For the following loads, plot their I-V curves onto the I-V curve for the source shown and at the crossover points note the current, voltage and power delivered to the load Current""(A)" I! + V Load - Source" 8" 7" 6" 5" 4" 3" 2" 1" 0" Source I-V curve 0" 4" 8" 12" 16" 20" 24" 28" Voltage"(V)" a Figure P2.13 The load is a simple 2-Ω resistor Find I, V and P b The load is an ideal battery that is always at 12V no matter what current c The source is charging a battery that is modeled as an ideal 12-V battery in series with a 2-Ω internal series resistance V v 2Ω resistor: i= = R 12V battery: v = 12 12V battery with 2Ω resistance: v = 12 + 2R Current""(A)" SOLN: 8" 7" 6" 5" 4" 3" 2" 1" 0" Source#I"V$ Ideal## 12V#ba&ery# ba&ery# 12V,#2Ω# 2Ω# 0" 4" 8" 12" 16" 20" 24" 28" Voltage"(V)" a 2-Ω : v = V, i = 4A, P = 32 W b 12V battery: v = 12 V, i = A, P = 36 W c 12V with 2Ω: v = 16 V, i = 2A, P = 32 W 2.14 Suppose a photovoltaic (PV) module consists of 40 individual cells wired in series, (a) In some circumstances, when all cells are exposed to the sun it can be modeled as a series combination of forty 0.5-V ideal batteries, (b) The resulting graph of current versus voltage would be a straight, vertical 20-V line as shown in (c) Gmasters Pg 11 Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems 12 SOLUTIONS Figure P2.14a a When an individual cell is shaded, it looks like a 5-Ω resistor instead of a 0.5-V battery, as shown in (d) Draw the I-V curve for the PV module with one cell shaded Figure P2.14b b With two cells shaded, as in (e), draw the I-V curve for the PV module on the same axes as you have drawn the full-sun and 1-cell shaded I-V lines SOLN: a With one cell shaded, the array looks like a 19.5V battery in series with ohms V = 19.5 − 5I which plots as shown below: Gmasters Pg 12 Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems b 13 SOLUTIONS With two cells shaded, the array V-I curve is given by V = 19 − 10 I which is also plotted in the above figure 2.15 If the photovoltaic (PV) module in Problem 2.14 is connected to a 5-Ω load, find the current, voltage and power delivered to the load under the following circumstances Comment on the power lost due to shading Figure P2.15 a Every cell in the PV module is in the sun SOLN: The full 20-V appears across the 5-Ω load, so V 20 = = 4A R V = 20V P = VI = 20x4 = 80W I= b One cell is shaded SOLN: Now we have a voltage divider driven by 20 - 0.5 = 19.5 V Gmasters Pg 13 Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems 14 SOLUTIONS 5&Ω& 19.5V& 5&Ω& V 19.5 = = 1.95A R 5+5 V = RI = ⋅1.95 = 9.75V P = VI = 9.75x1.95 = 19.0W I= Wow… that's a power loss of 76% just with one cell shaded ! c Two cells are shaded SOLN: 10$Ω$ 19V$ 5$Ω$ V 19 = = 1.267A R 10 + V = RI = ⋅1.267 = 6.333V P = VI = 6.333x1.267 = 8.0W I= That's a 90% power loss with just cells shaded ! 2.16 The core-and-coil inductor in Example 2.10 had an inductance that varied from 18.8 mH to 31.3 mH when the material's relative permeability ranged from 15,000 to 25,000 To avoid that uncertainty, it is common to add an air gap in the core so that its reluctance is the series sum of air gap and core reluctances Find the range of inductance that would result if the core in that example is built with a 0.001-m air gap Figure P2.16 SOLN: The reluctance of the ferromagnetic portion of the core when its relative permeability is 15,000 is Gmasters Pg 14 Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13 lOMoARcPSD|2935381 REEPS2 Chapter Problems Rcore = 15 SOLUTIONS lcore 0.099 = = 5252 A-t/Wb µcore A 15, 000 x 4π x 10 -7 x 0.001 And the air gap reluctance is Rair gap = lair gap µ0 A = 0.001 = 795, 775 A-t/Wb 4π x 10 -7 x 0.001 So the total reluctance is RTotal = 5,252 + 795,775 = 801,027 A-t/Wb And the inductance is N2 10 L= = = 0.0001248 = 0.1248 mH RTotal 801, 027 When the core's relative permeability is 25,000, the total reluctance is Rcore = 0.099 = 3151 A-t/Wb 25,000 x 4π x 10 -7 x 0.001 And the new total inductance is N2 10 L= = = 0.1251 x 10 -3H = 0.1251 mH R Total 3151 + 795, 775 This is an insignificant change in inductance A very precise inductance has been achieved at the expense of a sizeable decrease in inductance compared to the core without an air gap Gmasters Pg 15 Downloaded by EBOOKBKMT VMTC (nguyenphihung1009@gmail.com) 2/7/13