IEC 60598 2 8 Edition 3 0 2013 04 INTERNATIONAL STANDARD NORME INTERNATIONALE Luminaires – Part 2 8 Particular requirements – Handlamps Luminaires – Partie 2 8 Exigences particulières – Baladeuses IE[.]
IEC 60598-2-8:2013 ® Edition 3.0 2013-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Luminaires – Part 2-8: Particular requirements – Handlamps Luminaires – Partie 2-8: Exigences particulières – Baladeuses Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe IEC 60598-2-8 All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IEC's member National Committee in the country of the requester If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information Droits de reproduction réservés Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence IEC Central Office 3, rue de Varembé CH-1211 Geneva 20 Switzerland Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 info@iec.ch www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies About IEC publications The technical content of IEC publications is kept under constant review by the IEC Please make sure that you have the latest edition, a corrigenda or an amendment might have been published Useful links: IEC publications search - www.iec.ch/searchpub Electropedia - www.electropedia.org The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,…) It also gives information on projects, replaced and withdrawn publications The world's leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages Also known as the International Electrotechnical Vocabulary (IEV) on-line IEC Just Published - webstore.iec.ch/justpublished Customer Service Centre - webstore.iec.ch/csc Stay up to date on all new IEC publications Just Published details all new publications released Available on-line and also once a month by email If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csc@iec.ch A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des Normes internationales pour tout ce qui a trait l'électricité, l'électronique et aux technologies apparentées A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu Veuillez vous assurer que vous possédez l’édition la plus récente, un corrigendum ou amendement peut avoir été publié Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub Electropedia - www.electropedia.org La recherche avancée vous permet de trouver des publications CEI en utilisant différents critères (numéro de référence, texte, comité d’études,…) Elle donne aussi des informations sur les projets et les publications remplacées ou retirées Le premier dictionnaire en ligne au monde de termes électroniques et électriques Il contient plus de 30 000 termes et définitions en anglais et en franỗais, ainsi que les termes ộquivalents dans les langues additionnelles Egalement appelé Vocabulaire Electrotechnique International (VEI) en ligne Just Published CEI - webstore.iec.ch/justpublished Restez informé sur les nouvelles publications de la CEI Just Published détaille les nouvelles publications parues Disponible en ligne et aussi une fois par mois par email Service Clients - webstore.iec.ch/csc Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csc@iec.ch Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright © 2013 IEC, Geneva, Switzerland ® Edition 3.0 2013-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Luminaires – Part 2-8: Particular requirements – Handlamps Luminaires – Partie 2-8: Exigences particulières – Baladeuses INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE PRICE CODE CODE PRIX ICS 29.140.40 N ISBN 978-2-83220-789-5 Warning! Make sure that you obtained this publication from an authorized distributor Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé ® Registered trademark of the International Electrotechnical Commission Marque déposée de la Commission Electrotechnique Internationale Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe IEC 60598-2-8 60598-2-8 © IEC:2013 CONTENTS FOREWORD 8.1 Scope 8.2 Normative references 8.3 Terms and definitions 8.4 General test requirements 8.5 Classification of luminaires 8.6 Marking 8.7 Construction 8.8 Creepage distances and clearances 8.9 Provision for earthing 8.10 Terminals 8.11 External and internal wiring 8.12 Protection against electric shock 11 8.13 Endurance tests and thermal tests 11 8.14 Resistance to dust and moisture 12 8.15 Insulation resistance and electric strength 12 8.16 Resistance to heat, fire and tracking 12 Figure – Arrangement for impact test for handlamps Figure – Apparatus for flexing test 13 Figure – Crush test apparatus 14 Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe –2– –3– INTERNATIONAL ELECTROTECHNICAL COMMISSION LUMINAIRES – Part 2-8: Particular requirements – Handlamps FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees) The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”) Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work International, governmental and nongovernmental organizations liaising with the IEC also participate in this preparation IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter 5) IEC itself does not provide any attestation of conformity Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity IEC is not responsible for any services carried out by independent certification bodies 6) All users should ensure that they have the latest edition of this publication 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications 8) Attention is drawn to the Normative references cited in this publication Use of the referenced publications is indispensable for the correct application of this publication 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights IEC shall not be held responsible for identifying any or all such patent rights International Standard IEC 60598-2-8 has been prepared by subcommittee 34D: Luminaires, of IEC technical committee 34: Lamps and related equipment This third edition cancels and replaces the second edition, published in 1996, its Amendment (2000) and its Amendment (2007) It constitutes a technical revision This edition includes the following significant technical changes with respect to the previous edition a) The requirements have been updated to make them consistent and to solve contradicting requirements introduced in the Amendment In that amendment, a requirement was introduced specifying that handlamp shall always be classified as rough service luminaire only The implication of this statement was that according to 4.13.4 of Part this kind of luminaire shall always be IP54.This requirements is in contradiction with several points of this Part where it is considered acceptable for ordinary luminaires (e.g 8.11.1, 8.11.2 and 8.13.1) Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe 60598-2-8 © IEC:2013 60598-2-8 © IEC:2013 b) Furthermore, the contradiction between the requirement in 8.7.1 and 8.7.2 regarding the type of material used for the protective cover has been corrected This standard is intended to be read in conjunction with IEC 60598-1 Luminaires – Part 1: General requirements and tests It was established on the basis of the seventh edition (2008) of that standard The text of this standard is based on the following documents: FDIS Report on voting 34D/1090/FDIS 34D/1097/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table This publication has been drafted in accordance with the ISO/IEC Directives, Part A list of all parts in the IEC 60598 series, published under the general title Luminaires, can be found on the IEC website The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication At this date, the publication will be • • • • reconfirmed, withdrawn, replaced by a revised edition, or amended Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe –4– –5– LUMINAIRES – Part 2-8: Particular requirements – Handlamps 8.1 Scope This part of the IEC 60598 series specifies requirements for handlamps and similar portable luminaires which are held in the hand, hooked up or resting on a surface for use with electric light sources on supply voltages not exceeding 250 V It is to be read in conjunction with those sections of Part to which reference is made Handlamps which can be fixed to a support by means of a wing screw, clip or magnet, and luminaires intended for inspection of the interior of barrels, are within the scope of this part of IEC 60598 8.2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies IEC 60227 (all parts) Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V IEC 60245 (all parts), Rubber insulated cables – Rated voltages up to and including 450/750 V IEC 60598-1, Luminaires – Part 1: General requirements and tests 8.3 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 60598-1, as well as the following apply 8.3.1 handlamp luminaire with a handle and a flexible cable or cord, intended to be moved frequently while connected to the supply 8.3.2 rewirable handlamp handlamp with a type X or Y attachment 8.3.3 non-rewirable handlamp handlamp with a type Z attachment Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe 60598-2-8 © IEC:2013 60598-2-8 © IEC:2013 8.3.4 sealed handlamp handlamp of which all protective covers are sealed and which makes it impossible to replace the lamp without destroying the handlamp 8.4 General test requirements 8.4.1 The provisions of Section of IEC 60598-1 apply together with the requirements of 8.4.2 The tests described in each appropriate section of Part shall be carried out in the order listed in this Part 2-8 8.4.2 The requirements of the third paragraph of 0.4.2 of Section of IEC 60598-1 not apply In general, four samples are necessary for the tests, three of which are subjected to the tests of 8.7.6, the fourth sample being subjected to the other tests All four samples shall be subjected to the test for rough service hand-held luminaires of 4.13.4 b) of IEC 60598-1 For handlamps provided with a rubber protection cover, an additional sample is necessary for the test of 8.13.1 Where a range of similar handlamps is involved, the specified tests are made on a representative complete set from the range This set shall include handlamps, together with any attachments, which represents the most unfavourable combination 8.5 Classification of luminaires Luminaires shall be classified in accordance with the provisions of Section of IEC 60598-1 together with the requirements of 8.5.1and 8.5.2 8.5.1 According to the type of protection against electric shock, handlamps shall be classified as class II or class III 8.5.2 as: According to the method of connecting the cable or cord, handlamps shall be classified – rewirable handlamps, or – non-rewirable handlamps 8.6 Marking The provisions of Section of IEC 60598-1 apply, together with the requirements of 8.6.1, and 8.6.2 8.6.1 The symbol for class II or class III, the marking for rated voltage of class III handlamps and the symbol for the degree of protection against dust and moisture shall be on the outside of the handlamp This requirement is met if the marking is visible from the outside through a translucent cover The marking for maximum rated wattage shall not be in paint or ink, even when protected by varnish Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe –6– –7– Compliance shall be checked by inspection and by the test described in Section of IEC 60598-1 8.6.2 For handlamps with replaceable lamps and with type X attachment, the instructions regarding the method of opening and closing the luminaire shall be marked on the protective cover and shall remain visible during and after use 8.7 Construction The provisions of Section of IEC 60598-1 apply, together with the requirements of 8.7.1 to 8.7.6 8.7.1 The shell and handle of the handlamp shall be of insulating material 8.7.2 The lamp shall be protected against accidental damage by a protective grid, translucent cover or similar protective means These devices shall be rigidly fixed to the body of the handlamp and it shall not be possible to remove the device by hand The protective device shall remain attached to the handlamp during the lamp replacement, e.g by a hinge, chain or equally effective device If an automatic switch interrupts the operation of the luminaire, when the protective device is removed for maintenance, the protective device may not be permanently attached to the luminaire For handlamps with magnetic ballast for tubular fluorescent lamps, the removal of the protective device shall be so arranged that the opening occurs at the end of the lamp where the lamp holder is connected to the magnetic ballast If the protective device is of metal, it shall be so positioned or protected by insulation that it is not likely to be inadvertently touched when holding the handle The distance between the glass of the tungsten filament lamp or the tubular fluorescent lamp or any protective glass and a plane through the outside of two adjacent bars of a protective grid or a protective cover, shall be at least mm Suspension hooks, if any, shall be securely fixed to the handlamp Compliance is checked by inspection, by measurement and by loading the hook with a weight which is twice the weight of the luminaire, including the total weight of the attached cable, cord, ballast or transformer The hook shall not deform such that the luminaire slips from the means of suspension which for testing purposes, is a mm ∅ metal bar 8.7.3 Handlamps shall not use resistive ballasts or resistive cables to limit the current in discharge lamps 8.7.4 Lampholders for tungsten filament lamps shall be locked against rotation by at least two independent means, at least one of which shall be operable only with the aid of a tool The means of fixing shall not serve to fix any other part Compliance shall be checked by inspection and by manual test 8.7.5 Ballasts or transformers where connected in the flexible cable or cord shall be at a distance not greater than m from the plug and equipped with a suspension hook Compliance shall be checked by inspection, by manual test and by measurement 8.7.6 The test for mechanical strength described in 4.13 of Section of IEC 60598-1 does not apply, except the test of 4.13.4 b) as mentioned in 8.4.2 In addition, the mechanical Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe 60598-2-8 © IEC:2013 60598-2-8 © IEC:2013 strength shall be checked by the test described in 8.7.6.1, if applicable, and by the tests described in 8.7.6.2 8.7.6.1 The grid, translucent covers and protective covers shall be firmly fixed Compliance is checked by a pull of 100 N for h, applied to the parts of the body of the handlamp which, when loose, would allow to touch current-carrying parts For handlamps containing tubular fluorescent lamps this is likely along its longitudinal axis For sealed handlamps, in addition a torque test of 10 Nm shall be applied to the parts which, when loose, would allow to touch current-carrying parts The grid or protective covers shall remain in position during and after the test 8.7.6.2 The handlamp, fitted with a flexible cable or cord in accordance with the requirements of 8.11.2 and of suitable length, is subjected to two impact tests in which it is caused to swing against a steel bar which is mounted on a solid wall of brick, stone, concrete or similar material, as shown in Figure a b c Steel packing block IEC 953/13 The steel packing block is necessary only if the shape of the handlamp is such that, without it, the handlamp does not hit the bar For the key and further explanations, see 8.7.6.2 Figure – Arrangement for impact test for handlamps The bar is of 40 mm × 40 mm × mm right-angle section with the corner rounded to a radius of mm It is mounted in contact with the wall or, if necessary, in contact with a steel packing block which is in contact with the wall Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe –8– 60598-2-8 © CEI:2013 b) De plus, la contradiction entre les exigences 8.7.1 et 8.7.2 concernant le type de matériel utilisé pour le capot de protection a été corrigée Cette norme doit être lue conjointement avec la CEI 60598-1: Luminaires – Partie 1:Exigences générales et essais Elle a été établie sur la base de la septième édition (2008) de cette norme Le texte de cette norme est issu des documents suivants: FDIS Rapport de vote 34D/1090/FDIS 34D/1097/RVD Le rapport de vote indiqué dans le tableau ci-dessus donne toute information sur le vote ayant abouti l'approbation de cette norme Cette publication a été rédigée selon les Directives ISO/CEI, Partie Une liste de toutes les parties de la série CEI 60598, publiées sous le titre général Luminaires, peut être consultée sur le site web de la CEI Le comité a décidé que le contenu de cette publication ne sera pas modifié avant la date de stabilité indiquée sur le site web de la CEI sous "http://webstore.iec.ch" dans les données relatives la publication recherchée A cette date, la publication sera • • • • reconduite, supprimée, remplacée par une édition révisée, ou amendée Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe – 18 –