Bsi bs en 61915 1 2008

BRITISH STANDARD Low-voltage switchgear and controlgear — Device profiles for networked industrial devices — Part 1: General rules for the development of device profiles ICS 29.130.20 12&23 * ISO 15745 PROFILE STRUCTURE * * HEADER SECTION * BS EN 61915-1:2008 – 82 – * BODY SECTION * * ISO 15745 HEADER DATA TYPES * – 83 – BS EN 61915-1:2008 * ISO 15745 DEFINED DATA TYPES * * IEC 61915 SPECIFIC ELEMENTS * * (Examples if no existing ISO 15745 technology-specific elements) * BS EN 61915-1:2008 – 84 – – 85 – BS EN 61915-1:2008 BS EN 61915-1:2008 – 86 – – 87 – BS EN 61915-1:2008 BS EN 61915-1:2008 – 88 – – 89 – BS EN 61915-1:2008 * IEC 61915 SPECIFIC DATA TYPES * Figure D.2 – Device profile schema structure BS EN 61915-1:2008 – 90 – Annex E (informative) Categories of parameters E.1 General The use of the parameter categories given below will ensure consistent terminology among different IEC product committees NOTE These categories may be used as a basis to define parameter groups in a device profile E.2 Control parameters Control parameters are application information that is exchanged whilst the application is running with the control application, controller and other devices connected to the network The control parameters are used by the application The control parameters may include application diagnostics information E.3 Management parameters Management parameters include device diagnostic information, device state and device configuration information Device diagnostic information is used to provide information about the device’s condition Device state parameters may be defined to provide information about the state of the device Device configuration information is used to set up the device during application development, and when starting up the control equipment and the process NOTE Some devices may have no configuration data NOTE Some networks not support configuration of devices across the communication system E.4 Parameter categories Parameters can be classified into different categories such as the following: Control parameters Commands Switching commands Fault reset Operating mode selection Monitoring information Operational signals Fault signals Warning signals Maintenance signals Network errors – 91 – Measurements Operational measurements Maintenance measurements Management parameters Configuration Operational levels Fault levels Warning levels Maintenance levels I/O assignment Network configuration Diagnostics Operational diagnostics Fault diagnostics Warning diagnostics Maintenance diagnostics Network counters Counters reset Identification Product identification Manufacturer identification BS EN 61915-1:2008 BS EN 61915-1:2008 – 92 – Bibliography IEC 60947 (all parts), Low-voltage switchgear and controlgear NOTE Harmonized in EN 60947 series (not modified) ISO/IEC 4873 , Information technology – ISO 8-bit code for information interchange -Structure and rules for implementation (available in English only) ISO/IEC 8879, Information processing − Text and office systems − Standard Generalised Markup Language (SGML) NOTE Harmonized as EN 28879:1990 (not modified) ISO 15745-1, Industrial automation systems and integration − Open systems application integration framework − Part 1: Generic reference description REC-xml-20001006, Extensible Markup Language (XML) 1.0 Second Edition – W3C Recommendation October 2000 REC-xmlschema-1-20010502 , XML Schema Part 1: Structures – W3C Recommendation 02 May 2001 REC-xmlschema-2-20010502, XML Schema Part 2: Datatypes – W3C Recommendation 02 May 2001 ⎯⎯⎯⎯⎯⎯⎯ – 93 – BS EN 61915-1:2008 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies Publication IEC 60559 Year 1989 Title Binary floating-point arithmetic for microprocessor systems EN/HD HD 592 S1 Year 1991 IEC 61131-3 2003 Programmable controllers Part 3: Programming languages EN 61131-3 2003 IEC/TR 62390 2005 Common automation device - Profile guideline - - ISO 1000 A1 1992 1998 SI units and recommendations for the use of their multiples and of certain other units - ISO 15745 Series Industrial automation systems and integration - Open systems application integration framework - - ISO/IEC 10646 2003 Information technology - Universal multipleoctet coded character set (UCS) - - ISO/IEC 19501 2005 Information technology - Open Distributed Processing - Unified Modeling Language (UML) Version 1.4.2 - - BS EN 61915-1:2008 BSI — British Standards Institution BSI is the independent national body responsible for preparing British Standards It presents the UK view on standards in Europe and at the international level It is incorporated by Royal Charter Revisions British Standards are updated by amendment or revision Users of British Standards should make sure that they possess the latest amendments or editions It is the constant aim of BSI to improve the quality of our products and services We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400 BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: orders@bsi-global.com Standards are also available from the BSI website at http://www.bsi-global.com In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service Various BSI electronic information services are also available which give details on all its products and services Contact the Information Centre Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: info@bsi-global.com Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards For details of these and other benefits contact Membership Administration Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: membership@bsi-global.com Information regarding online access to British Standards via British Standards Online can be found at http://www.bsi-global.com/bsonline Further information about BSI is available on the BSI website at http://www.bsi-global.com Copyright Copyright subsists in all BSI publications BSI also holds the copyright, in the UK, of the publications of the international standardization bodies Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI BSI 389 Chiswick High Road London W4 4AL This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained Details and advice can be obtained from the Copyright & Licensing Manager Tel: +44 (0)20 8996 7070 Fax: +44 (0)20 8996 7553 Email: copyright@bsi-global.com