BS EN 61784-5-12:2012+A1:2015 BS EN 61784-5-12:2012 BSI Standards Publication Industrial communication networks — Profiles Part 5-12: Installation of fieldbuses — Installation profiles for CPF 12 BS EN 61784-5-12:2012+A1:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 61784-5-12:2012+A1:2015 It is identical to IEC 61784-5-12:2010, incorporating amendment 1:2015 It supersedes BS EN 61784-5-12:2012, which is withdrawn The start and finish of text introduced or altered by amendment is indicated in the text by tags Tags indicating changes to IEC text carry the number of the IEC amendment For example, text altered by IEC amendment is indicated by The UK participation in its preparation was entrusted to Technical Committee AMT/7, Industrial communications: process measurement and control, including fieldbus A list of organizations represented on this committee can be obtained on request to its secretary This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application © The British Standards Institution 2015 Published by BSI Standards Limited 2015 ISBN 978 580 90356 ICS 25.040.40; 35.100.40 Compliance with a British Standard cannot confer immunity from legal obligations This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2012 Amendments/corrigenda issued since publication Date Text affected 31 October 2015 Implementation of IEC amendment 1:2015 with CENELEC endorsement A1:2015 Annex ZA amended EUROPEAN STANDARD 61784-5-12 EN 61784-5-12:2012+A1 NORME EUROPÉENNE EUROPÄISCHE NORM April 2012 2015 September ICS 25.040.40; 35.100.40 English version Industrial communication networks Profiles Part 5-12: Installation of fieldbuses Installation profiles for CPF 12 (IEC 61784-5-12:2010) Industrial communication networks Profiles Part 5-12: Installation of fieldbuses Installation profiles for CPF 12 (CEI 61784-5-12:2010) Industrielle Kommunikationsnetze Profile Teil 5-12: Feldbusinstallation Installationsprofile für die Kommunikationsprofilfamilie 12 (IEC 61784-5-12:2010) This European Standard was approved by CENELEC on 2011-10-19 CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels © 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members Ref No EN 61784-5-12:2012 E BS EN EN 61784-5-12:2012 BS BS EN 61784-5-12:2012+A1:2015 61784-5-12:2012 EN 61784-5-12:2012 EN 61784-5-12:2012+A1:2015 EN 61784-5-12:2012 – 2- 2– -2- Foreword Foreword The text of document 65C/602/FDIS, future edition of IEC 61784-5-12, prepared by SC 65C, "Industrial The text of of document 65C/602/FDIS, future edition of IEC control 61784-5-12, prepared bywas SCsubmitted 65C, "Industrial networks", IEC/TC 65, "Industrial-process measurement, and automation" to the networks", of IEC/TC 65, "Industrial-process measurement, control and automation" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61784-5-12:2012 IEC-CENELEC parallel vote and approved by CENELEC as EN 61784-5-12:2012 The following dates are fixed: The following dates are fixed: • • • • latest date by which the document has latest date by whichatthe document to be implemented national levelhas by to be implemented at national level by publication of an identical national publication identical national standard orof byan endorsement standard or by endorsement latest date by which the national latest date conflicting by which the standards withnational the standards conflicting the document have to be with withdrawn document have to be withdrawn (dop) (dop) 2012-10-20 2012-10-20 (dow) (dow) 2014-10-19 2014-10-19 This standard is to be used in conjunction with IEC 61918, second edition (2010-07), together with the This standard is to be used in conjunction withEN IEC 61918, second edition (2010-07), together with the European Common Modification published with 61918:2008 European Common Modification published with EN 61918:2008 Attention is drawn to the possibility that some of the elements of this document may be the subject of Attention is drawn to the[and/or possibility that some elements of this beall thesuch subject of patent rights CENELEC CEN] shall not of bethe held responsible for document identifying may any or patent EN 61784-5-12:2012/A1:2015 patent rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights rights EN 61784-5-12:2012/A1:2015 EN 61784-5-12:2012/A1:2015 Endorsement notice Endorsement notice The text of the International Standard IEC 61784-5-12:2010 was approved by CENELEC as a European European foreword The text of the International Standard IEC 61784-5-12:2010 was approved by CENELEC as a European Standard without any modification Standard without any modification European foreword European foreword The text of document 65C/768/CDV, future IEC 61784-5-12:2010/A1, prepared by SC 65C "Industrial Forewordmeasurement, to amendment networks" of IEC/TC 65 "Industrial-process controlA1 and automation" was submitted to The text of document 65C/768/CDV, future IEC prepared by SC 65C "Industrial the IEC-CENELEC parallel vote and approved by61784-5-12:2010/A1, CENELEC as EN 61784-5-12:2012/A1:2015 networks" IEC/TC 65 "Industrial-process measurement, control andprepared automation" was submitted to The text ofofdocument 65C/768/CDV, future IEC 61784-5-12:2010/A1, by SC 65C "Industrial the IEC-CENELEC vote and approved by CENELECcontrol as EN and 61784-5-12:2012/A1:2015 networks" of IEC/TC 65fixed: "Industrial-process measurement, automation" was submitted to The following dates parallel are the IEC-CENELEC parallel vote and approved by CENELEC as EN 61784-5-12:2012/A1:2015 The following dates are fixed: (dop) 2016-04-22 • latest date by which the document has to be implemented at The national followinglevel dates fixed: of an identical national byare publication (dop) 2016-04-22 • latest dateorby the document has to be implemented at standard bywhich endorsement national level by publication of an identical national (dop) 2016-04-22 • latest date by which the document has to be implemented at orby byby endorsement national level publication of anstandards identical national (dow) 2018-07-22 • standard latest date which the national conflicting with standard or byhave endorsement the document to be withdrawn (dow) 2018-07-22 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2018-07-22 • latest date by which the national standards conflicting with the document have to be withdrawn Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such is drawn to the possibility that some of the elements of this document may be the subject of Attention patent rights patent rights CENELEC [and/or CEN] shall not be elements held responsible for identifying any all such Attention is drawn to the possibility that some of the of this document may be theorsubject of patent patent rights rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights Endorsement notice Endorsement notice Endorsement notice The text of the International Standard IEC 61784-5-12:2010/A1:2015 was approved by CENELEC as a European Standard without any modification The text of the International Standard IEC 61784-5-12:2010/A1:2015 was approved by CENELEC as a European Standard withoutStandard any modification The text of the International IEC 61784-5-12:2010/A1:2015 was approved by CENELEC as a European Standard without any modification with their corresponding European publications BS EN 61784-5-12:2012+A1:2015 EN 61784-5-12:2012+A1:2015 BS EN 61784-5-12:2012 The following documents, in whole or in part, are referenced in this EN document and are - normatively 61784-5-12:2012 indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies BS EN 61784-5-12:2012 Annex ZA 361784-5-12:2012 NOTE When an International Publication has been- modified by common modifications, EN indicated by (mod), –3– the relevant EN/HD applies (normative) EN 61784-5-12:2012/A1:2015 Annex Normative to international publications NOTE Up-to-date information references on the latest versions ofZA the European Standards listed in this annex is available here: www.cenelec.eu (normative) with their corresponding European publications Annex ZA The referenced documents are for the application ofinthis Normative references to normatively international publications Thefollowing following documents, in whole or inindispensable part, are referenced thisdocument documentFor anddated are BS EN 61784-5-12:2012 (normative) references, only the edition cited applies For undated references, the latest edition of the referenced indispensable for its application dated references, only the edition cited applies For undated with their For corresponding European publications -3Year Title EN/HD EN 61784-5-12:2012 Year Publication document (including any amendments) applies references, the latest edition of the referenced document (including any amendments) applies The following referenced documents are indispensable for the application of this document For dated Normative references tobyinternational publications NOTE When an international publication has been modified common modifications, indicated by (mod), the relevant EN/HD NOTE 1 When International Publication been modified by commonthe modifications, indicated (mod), Replacement inanAnnex ZA ofcited EN 61784-5-12:2012: references, only the edition applies.has For undated references, latest edition of thebyreferenced applies the relevant EN/HD applies with their corresponding European publications document (including any amendments) applies.Annex ZA IEC 61918 (mod) 2013 Industrial communication networks EN 61918 2013 (normative) Publication Title EN/HD listed in this annex Year is NOTE 2 Up-to-dateYear information on the latest versions of thenetworks European Standards Installation of communication in NOTE When an www.cenelec.eu international publication has been modified by common modifications, indicated EN/HD -available + AC by (mod), the relevant 2014 here: industrialand premises applies IEC 61156-5 Multicore symmetrical pair/quad cables Normative references to international publications forwhole digitalor communications The following documents, in in part, are normatively referenced in this document and are with their corresponding European publications Publication Year Title EN/HD Year Part 5: Symmetrical pair/quad cables Addition to Annex ZA of EN 61784-5-12:2012: indispensable for its application For dated references, only thewith edition cited applies For undated transmission characteristics up to 000 MHz references, thereferenced latest edition of the referenced document (including any amendments) applies For IEC 61156-5 Multicore and symmetrical pair/quad -of 60603-7-3 IEC Connectors for electronic equipment -cables EN dated The 60603-7-3 following documents are indispensable for the application this document Horizontal floor wiring - Sectional specification for digital communications Part 7-3: Detail specification for 8-way, references, only the edition cited applies For undated references, the latest edition of the referenced NOTE When an International Publication has modified by -common indicated by- (mod), Part 5: Symmetrical pair/quad cables IEC 61918 Industrial communication networks shielded, free andbeen fixed connectors, forwith modifications, document (including2010 any amendments) applies the relevant EN/HD applies Installation transmission characteristics up to 000 MHz of communication networks data transmission with frequencies upinto Horizontal floor wiringby- Sectional specification industrial NOTE When an international publication haspremises been modified common modifications, indicated by (mod), the relevant EN/HD 100 MHz NOTE Up-to-date information on the latest versions of the European Standards listed in this annex is applies.2 IEC 61918 2010 Industrial communication networks available here: www.cenelec.eu EN 60793-2 series series Optical fibres IEC 60793-2 Installation of communication networks in Part specifications Publication Year Title 2: Product EN/HD Year industrial premises IEC 61156-5 Multicore and symmetrical pair/quad cables for digital communications Year Title EN/HD Year Publication Part 5: Symmetrical pair/quad cables with transmission characteristics up to 000 MHz Replacement in Annex ZA of Horizontal EN 61784-5-12:2012: floor wiring - Sectional specification IEC 61918 (mod) 2010 2013 - - Industrial communication networks in Installation of communication networks in industrial premises - 61918 EN 2013 + AC 2014 Addition to Annex ZA of EN 61784-5-12:2012: IEC 60603-7-3 - Connectors for electronic equipment Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 100 MHz EN 60603-7-3 - IEC 60793-2 series Optical fibres Part 2: Product specifications EN 60793-2 series BS EN 61784-5-12:2012+A1:2015 IEC 61784-5-12:2012+A1:2015 –4– –2– BS EN 61784-5-12:2012 61784-5-12 © IEC:2010(E) CONTENTS INTRODUCTION Scope .6 Normative references .6 Terms, definitions and abbreviated terms CPF 12: Overview of installation profiles Installation profile conventions 6 Conformance to installation profiles Annex A (Normative) CP 12/1 + CP 12/2 (EtherCAT™) specific installation profile .8 Figure – Standards relationships Table A.1 – Network characteristics for balanced cabling based on Ethernet 10 Table A.2 – Network characteristics for optical fibre cabling 11 Table A.3 –Information relevant to copper cable: CP12/1, CP12/2 fixed cables 12 Table A.4 – Information relevant to copper cable: CP12/1, CP12/2 flexible cables 13 Table A.5 –Information relevant to copper cable: CP12/1, CP12/2 special cables 13 Table A.6 – Information relevant to optical fibre cables 14 Table A.7 – Connectors for balanced cabling CPs based on Ethernet 15 Table A.8 – Optical fibre connecting hardware 15 Table A.9 – Relationship between FOC and fibre types (CP 12/1 and CP 12/2)���������������� 15 BS EN 61784-5-12:2012+A1:2015 IEC 61784-5-12:2012+A1:2015 –5– BS EN 61784-5-12:2012 61784-5-12 © IEC:2010(E) –5– INTRODUCTION This International Standard is one of a series produced to facilitate the use of communication networks in industrial control systems IECIEC 61918:2010 provides the common requirements for for thetheinstallation 61918:2013 provides the common requirements installationofof communication communication networks ininindustrial industrial control systems This installation profile standard provides the networks control systems This installation profile standard provides the installation installation profiles of the communication profiles (CP)communication of a specific communication profile profiles of the communication profiles (CP) of a specific profile family (CPF) by family (CPF) stating which of IEC 61918 apply and, where necessary, by stating which by requirements of requirements IEC 61918 fully apply and, fully where necessary, by supplementing, modifying, or replacing the other requirements (seerequirements Figure 1) supplementing, modifying, or replacing the other (see Figure 1) For general background on fieldbuses, their profiles, and relationship between the installation profiles specified in this standard, see IEC/TR 61158-1 Each CP installation profile is specified in a separate annex of this standard Each annex is structured exactly as the reference standard IEC 61918 for the benefit of the persons representing the roles in the fieldbus installation process as defined in IEC 61918 (planner, installer, verification personnel, validation personnel, maintenance personnel, administration personnel) By reading the installation profile in conjunction with IEC 61918, these persons immediately know which requirements are common for the installation of all CPs and which are modified or replaced The conventions used to draft this standard are defined in Clause The provision of the installation profiles in one standard for each CPF (for example IEC 61784-5-12 for CPF 12), allows readers to work with standards of a convenient size PLANNING AND INSTALLATION DESIGN ISO/IEC 11801 Offices Annex HOMES ISO/IEC 15018 Home Annex DATA CENTRES ISO/IEC 24764 OFFICE PREMISES GENERIC CABLING BETWEEN AUTOMATION ISLANDS INDUSTRIAL PREMISES BETWEEN AUTOMATION ISLANDS WITHIN AUTOMATION ISLANDS ISO/IEC 14763-2 Data centre Annex Industrial Annex ISO/IEC 24702 IEC 61158 series and IEC 61784-1, -2 Installation Profiles IEC 61918 IEC 61784-5 series (Selection + Add/Repl/Mod) APPLICATION-SPECIFIC CABLING Figure – Standards relationships (Common requirements) Common structure BS EN 61784-5-12:2012+A1:2015 IEC 61784-5-12:2012+A1:2015 Scope –6 6– – – BS EN 61784-5-12:2012 61784-5-12 © IEC:2010(E) BS EN 61784-5-12:2012 61784-5-12 NETWORKS – © IEC:2010(E) BS EN 61784-5-12:2012 61784-5-12 NETWORKS – © IEC:2010(E) –6– INDUSTRIAL COMMUNICATION PROFILES – –6– INDUSTRIAL COMMUNICATION PROFILESof– fieldbuses – Part 5-12: Installation INDUSTRIAL COMMUNICATION NETWORKS – Installation profiles for CPF 12 PROFILESof– fieldbuses – Part 5-12: Installation Installation profiles for CPF 12 Part 5-12: Installation of fieldbuses – Installation profiles for CPF 12 ThisScope part of IEC 61784 specifies the installation profiles for CPF 12 (EtherCAT™) 1 ThisScope part of IEC 61784 the installation profiles for CPF The installation profiles are in This read in in conjunction conjunction with installation profilesspecifies are specified specified in the the annex annex12is(EtherCAT™) read with 61918:2013 IECIEC 61918:2010 The profilesspecifies are specified in the annex This annex12is(EtherCAT™) read in conjunction with This installation part of IEC 61784 the installation profiles for CPF IEC 61918:2010 Normative references CPF 12: Overview of installation profiles The installation profiles are specified in the annex This annex is read in conjunction with IEC 61918:2010 references The Normative following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including are any indispensable amendments) for applies The following referenced documents the application of this document Normative references For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any indispensable amendments) applies IEC 61918:2010 Industrial communication networks – Installation ofofcommunication networks IEC 61918:2013 Industrial communication networks – for Installation communication networks The following referenced documents are the application of this document industrial premises in industrial premises For dated references, only the edition cited applies For undated references, the latest edition IEC 61918:2010 networks – Installation of the referencedIndustrial documentcommunication (including any amendments) applies of communication networks The normative references IEC IEC61918:2010, 61918:2013 , Clause 2, apply Forprofile profilespecific specific normative normative in industrial premises The normative referencesofof Clause 2, apply For references, see Clause A.2 A.2.communication networks – Installation of communication networks references, see Clause IEC 61918:2010 Industrial The normative references of IEC 61918:2010, Clause 2, apply For profile specific normative in industrial premises IEC 60603-7-3, Connectors for electronic equipment – Part 7-3: Detail specification for 8-way, references, see Clause A.2 shielded, freedefinitions and fixed connectors, for data transmission with frequencies up to 100 MHz Terms, and abbreviated terms The normative references of IEC 61918:2010, Clause 2, apply For profile specific normative A.2 references, Clause IEC 60793-2see (all subparts), Optical fibres – Partterms 2: Product specifications definitions and abbreviated For Terms, the purposes of this document, the terms, definitions and abbreviated terms of IEC 61918:2010, Clause 3, apply For Terms, the purposes of this the terms terms, definitions and abbreviated terms of definitions anddocument, abbreviated IEC 61918:2010, Clause 3, apply For the purposes purposes of this this document, document, the the terms, terms, definitions definitions and abbreviated abbreviated terms of 61918:2013 , Clause 3, apply IECIEC 61918:2010, Clause 3, apply 12: Overview of installation profiles CPFCPF 12 consists of two communication profiles as specified in IEC 61784-2 CPFCPF 12 consists of two communication profiles as specified in IEC I/O 61784-2 12: Overview of installation profiles The installation requirements for CP 12/1 (simple EtherCAT™ devices) and CP 12/2 (EtherCAT™ devices with mailbox capabilities) are identical and are specified in Annex A The 12 installation requirements for CP 12/1 (simple EtherCAT™ devices) and CP 12/2 CPF consists of two communication profiles as specified in IEC I/O 61784-2 (EtherCAT™ devices with mailbox capabilities) are identical and are specified in Annex A Installation profile conventions The installation requirements for CP 12/1 (simple EtherCAT™ I/O devices) and CP 12/2 (EtherCAT™ devices with mailbox capabilities) are identical and are specified in Annex A conventions The Installation numbering of profile the clauses and subclauses in the annexes of this standard corresponds to the numbering of IEC IEC 61918 main clauses and subclauses The Installation numbering of profile the clauses and subclauses in the annexes of this standard corresponds to conventions the numbering of IEC and IEC 61918 main clauses and subclauses The annex clauses subclauses of this standard supplement, modify, or replace the respective clauses and subclauses in IEC 61918 The numbering of the clauses and subclauses in the annexes of this standard corresponds to The annex clauses subclauses of this standard supplement, modify, or replace the the numbering of IEC and IEC 61918 main clauses and subclauses respective clauses and subclauses in IEC 61918 The annex clauses and subclauses of this standard supplement, modify, or replace the ——————— respective clauses andname subclauses in IEC EtherCAT™ is a trade of Beckhoff, Verl 61918 This information is given for the convenience of users of this International Standard and does not constitute an endorsement by IEC of the trademark holder or any of its ——————— products Compliance to this profile does not require use of the trade name Use of the trade name requires EtherCAT™ a trade of Beckhoff, Verl This information is given for the convenience of users of this permission ofisthe trade name name holder International Standard and does not constitute an endorsement by IEC of the trademark holder or any of its ——————— products Compliance to this profile does not require use of the trade name Use of the trade name requires EtherCAT™ a trade of Beckhoff, Verl This information is given for the convenience of users of this permission ofisthe trade name holder International Standard and does not constitute an endorsement by IEC of the trademark holder or any of its products Compliance to this profile does not require use of the trade name Use of the trade name requires permission of the trade name holder BS EN 61784-5-12:2012+A1:2015 IEC 61784-5-12:2012+A1:2015 –7– BS EN 61784-5-12:2012 61784-5-12 © IEC:2010(E) –7– Where there subclause of thenormative normativeannexes annexes in there isisno nocorresponding corresponding subclause of IEC IEC 61918:2013 61918:2010 in inthe this standard, without modification standard, the thesubclause subclauseofofIEC IEC61918 61918applies applies without modification The annex heading letter represents the installation profile assigned in Clause The annex (sub)clause numbering following the annex letter shall represent the corresponding (sub)clause numbering of IEC 61918 EXAMPLE “Annex B.4.4” in IEC 61784-5-3 means that CP 3/2 specifies the Subclause 4.4 of IEC 61918 All main clauses of IEC 61918 are cited and apply in full unless otherwise stated in each normative installation profile annex If all subclauses of a (sub)clause are omitted, then the corresponding IEC 61918 (sub)clause applies If in a (sub)clause it is written IEC 61918 (sub)clause does not apply “Not applicable.”, then the corresponding If in a (sub)clause it is written “Addition:”, then the corresponding IEC 61918 (sub)clause applies with the additions written in the profile If in a (sub)clause it is written “Replacement:”, then the text provided in the profile replaces the text of the corresponding IEC 61918 (sub)clause NOTE A replacement can also comprise additions If in a (sub)clause it is written “Modification:”, then the corresponding IEC 61918 (sub)clause applies with the modifications written in the profile If all (sub)clauses of a (sub)clause are omitted but in this (sub)clause it is written “(Sub)clause x has addition:” (or “replacement:”) or “(Sub)clause x is not applicable.”, then (sub)clause x becomes valid as declared and all the other corresponding IEC 61918 (sub)clauses apply Conformance to installation profiles Each installation this standard includes part part of .ItIt may may also installationprofile profilewithin within this standard includes ofIEC IEC61918:2013 61918:2010 include include defined definedadditional additionalspecifications specifications A statement of compliance to an installation profile of this standard shall be stated as either and for Compliance to IEC 61784-5-12:2010 for CP 12/m CPAm.1 12/m or or Compliance to IEC 61784-5-12:2010 Compliance and for CP 12/m Compliance to to IEC IEC61784-5-12 61784-5-12(Ed.1.0 (Ed.1.0) forAm.1) CP 12/m where the name within the angle brackets < > is optional and the angle brackets are not to be included The m n within CP 12/m shall be replaced by the profile number or NOTE The name may be the name of the profile, for example EtherCAT™ If the name is a trade name then the permission of the trade name holder shall be required Product standards shall not include any conformity assessment aspects (including quality management provisions), neither normative nor informative, other than provisions for product testing (evaluation and examination) ——————— In accordance with ISO/IEC Directives The date should not be used when the edition number is used BS EN 61784-5-12:2012+A1:2015 IEC 61784-5-12:2012+A1:2015 –8– –8– BS EN 61784-5-12:2012 61784-5-12 © IEC:2010(E) Annex A (normative) CP 12/1 + CP 12/2 (EtherCAT™) specific installation profile A.1 Installation profile scope Addition: This standard specifies the installation profile for Communication Profiles CP 12/1 and CP12/2 (EtherCAT™) The CP12/1 and CP12/2 are specified in IEC 61784-2 A.2 Normative references Addition: IEC 61156-5, Multicore and symmetrical pair/quad cables for digital communications - Part 5: Symmetrical pair/quad cables with transmission characteristics up to 000 MHz - Horizontal floor wiring – Sectional specification A.3 Installation profile terms, definitions, and abbreviated terms A.3.1 Terms and definitions A.3.2 Abbreviated terms A.3.3 Conventions for installation profiles Not applicable A.4 Installation planning A.4.1 Introduction A.4.1.1 Objective A.4.1.2 Cabling in industrial premises A.4.1.3 The planning process A.4.1.4 Specific requirements for CPs Not applicable –9– BS EN 61784-5-12:2012 61784-5-12 © IEC:2010(E) A.4.1.5 A.4.2 A.4.2.1 BS EN 61784-5-12:2012+A1:2015 IEC 61784-5-12:2012+A1:2015 –9– Specific requirements for generic cabling in accordance with ISO/IEC 24702 Planning requirements Safety A.4.2.1.1 General A.4.2.1.2 Electric safety A.4.2.1.3 Functional safety A.4.2.1.4 Intrinsic safety Not applicable A.4.2.1.5 Safety of optical fibre communication systems A.4.2.2 Security A.4.2.3 Environmental considerations and EMC A.4.2.3.1 Description methodology A.4.2.3.2 Use of the described environment to produce a bill of material A.4.2.4 A.4.3 A.4.3.1 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Network capabilities Network topology A.4.3.1.1 Common description A.4.3.1.2 Basic physical topologies for passive networks Not applicable A.4.3.1.3 Basic physical topologies for active networks Addition: Ring topologies shall be used when cable redundancy is required A.4.3.1.4 Combination of basic topologies Replacement: The combination of basic topologies is allowed according to A.4.3.1.5 A.4.3.1.5 Specific requirements for CPs Addition: Slave devices with more than two ports shall be used to combine basic active topologies BS EN 61784-5-12:2012+A1:2015 IEC 61784-5-12:2012+A1:2015 – 10 – BS EN 61784-5-12:2012 61784-5-12 © IEC:2010(E) – 10 – A.4.3.1.6 A.4.3.2 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Network characteristics A.4.3.2.1 General A.4.3.2.2 Network characteristics for balanced cabling not based on Ethernet Not applicable A.4.3.2.3 Network characteristics for balanced cabling based on Ethernet Replacement: Table A.1 A.1provides providesvalues valuesbased basedonon the template given in IEC Table 2 Table the template given in IEC 61918:2010, 61918:2013 , Table Table A.1 – Network characteristics for balanced cabling based on Ethernet Characteristic CP 12/1, CP12/2 (EtherCAT) Supported data rates (Mbit/s) 100 Supported channel length (m) b 100 Number of connections in the channel (max.) a b Patch cord length (m) a 100 (AWG22) Channel class per ISO/IEC 24702 (min.) b D Cable category per ISO/IEC 24702 (min.) c Connecting HW category per ISO/IEC 24702 (min.) Cable types No specific requirement; up to manufacturer's differentiation a See See 4.4.3.2 A.4.4.3.2. b For the purpose of this table, the channel definitions of ISO/IEC 24702 are applicable c For additional information see IEC 61156 series A.4.3.2.4 Network characteristics for optical fibre cabling Replacement: Table the template given in IEC 61918:2013 , Table Table A.2 A.2provides providesvalues valuesbased basedonon the template given in IEC61918:2010, Table 3 BS EN 61784-5-12:2012+A1:2015 IEC 61784-5-12:2012+A1:2015 – 11 – –4– IEC 61784-5-12:2010/AMD1:2015 IEC 2015 Table A.2 – Network characteristics for optical fibre cabling CP 12/1 and CP12/2 Optical fibre type Single mode silica Description Bandwidth (MHz) or equivalent at λ (nm) 300 at 310 Minimum length (m) Maximum length a (m) 14 000 Maximum channel insertion loss/optical power budget (dB) see IEEE 802.3 Clause 58 10 km specified Multimode silica POF Hard clad silica a A.4.4.1.4 Connecting hardware See A.4.4.2.5 Modal bandwidth (MHz × km) at λ (nm) 600 at 310 Minimum length (m) Maximum length a (m) 000 Maximum channel insertion loss/optical power budget (dB) 4,5 Connecting hardware See A.4.4.2.5 Modal bandwidth (MHz × 100 m) at λ (nm) 35 at 650 Minimum length (m) 0,055 Maximum length a (m) 50 Maximum channel insertion loss/optical power budget (dB) 4,2 Connecting hardware See A.4.4.2.5 Modal bandwidth (MHz × km) at λ (nm) 70 at 650 Minimum length (m) Maximum length a (m) 100 Maximum channel insertion loss/optical power budget (dB) Connecting hardware See A.4.4.2.5 This value is reduced by connections, splices and bends in accordance with formula (1) in 4.4.3.4.1 of IEC 61918:2013 Optical fibre cables Replace the existing Table A.6 with the following Table A.6: BS EN 61784-5-12:2012+A1:2015 IEC 61784-5-12:2012+A1:2015 Cladding diameter (μm) 230 NA 0,37 ± 0,04 – 12 –(m) Minimum length Maximum length (m) 100 A.4.3.2.5 Specific network characteristics A.4.3.2.6 Specific requirements for generic cabling in accordance with ISO/IEC 24702 A.4.4 Selection and use of cabling components A.4.4.1 Cable selection A.4.4.1.1 Common description A.4.4.1.2 Copper cables A.4.4.1.2.1 Balanced cables for Ethernet based CPs Replacement: Table A.4A.4 andand Table A.5 provide values for different cable types the template Table A.3, A.3,Table Table Table A.5 provide values for different cablebased typesonbased on the given in IEC in 61918:2013 , TableTable 4 template given IEC 61918:2010, Table A.3 –Information relevant to copper cable: CP12/1, CP12/2 fixed cables Characteristic CP 12/1, CP12/2 (EtherCAT) Type A cable Nominal impedance of cable (tolerance) 100 Ω ± 15 Ω (IEC 61156-5) Balanced or unbalanced Balanced DCR of conductors ≤ 115 Ω/km DCR of shield Tbd Number of conductors Shielding S/FTP, S/FTQ, S/STP Colour code for conductor WH, BU / YE, OG Jacket colour requirements - Jacket material - BS EN 61784-5-12:2012 Resistance to harsh environment (e.g UV, oil resist, LS0H) 61784-5-12 © IEC:2010(E) – 13 – Application dependent Transfer Impedance < 50 mΩ/m at 10 MHz Installation Type Characteristic CP 12/1, (EtherCAT) Stationary, noCP12/2 movement after installation Type A cable Outer cable diameter 5,5 mm – mm Wire cross section AWG 22/1 Wire diameter 1,5 mm ± 0,1 mm Delay scew a ≤ 20 ns/100 m a Relevant only for networks with time based synchronization Table A.4 – Information relevant to copper cable: CP12/1, CP12/2 flexible cables Characteristic CP 12/1, CP12/2 (EtherCAT) Type B cable Nominal impedance of cable (tolerance) 100 Ω ± 15 Ω (IEC 61156-5) Balanced or unbalanced Balanced DCR of conductors ≤ 115 Ω/km DCR of shield Tbd Number of conductors Shielding S/FTP, S/FTQ, S/STP Colour code for conductor WH, BU / YE, OG Wire cross section AWG 22/1 Wire diameter 1,5 mm ± 0,1 mm – 13 – Delay scew a BS EN 61784-5-12:2012+A1:2015 61784-5-12:2012+A1:2015 ≤ 20 ns/100 m IEC a Relevant only for networks with time based synchronization Table A.4 – Information relevant to copper cable: CP12/1, CP12/2 flexible cables Characteristic CP 12/1, CP12/2 (EtherCAT) Type B cable Nominal impedance of cable (tolerance) 100 Ω ± 15 Ω (IEC 61156-5) Balanced or unbalanced Balanced DCR of conductors ≤ 115 Ω/km DCR of shield Tbd Number of conductors Shielding S/FTP, S/FTQ, S/STP Colour code for conductor WH, BU / YE, OG Jacket colour requirements - Jacket material - Resistance to harsh environment (e.g UV, oil resist, LS0H) Application dependent Transfer Impedance < 50 mΩ/m at 10 MHz Installation Type Flexible, occasional movement or vibration Outer cable diameter 5,5 mm – mm Wire cross section AWG 22/7 Wire diameter 1,5 mm ± 0,1 mm Delay scew a ≤ 20 ns/100 m a Relevant only for networks with time based synchronization Table A.5 –Information relevant to copper cable: CP12/1, CP12/2 special cables Characteristic CP 12/1, CP12/2 (EtherCAT) Type C cable Nominal impedance of cable (tolerance) 100 Ω ± 15 Ω (IEC 61156-5) Balanced or unbalanced Balanced DCR of conductors ≤ 115 Ω/km DCR of shield Tbd Number of conductors Shielding S/FTP, S/FTQ, S/STP Colour code for conductor – 14 – BS EN 61784-5-12:2012 61784-5-12 © IEC:2010(E) WH, BU / YE, OG Jacket colour requirements Characteristic Jacket material - Resistance to harsh environment (e.g UV, oil resist, LS0H) Application dependent Transfer Impedance < 50 mΩ/m at 10 MHz Installation Type Special applications (e.g permanent movement as in drag chains) Outer cable diameter Application dependent Wire cross section AWG 22/x (x: e.g / 19) Wire diameter 1,5 mm ± 0,1 mm Delay scew a ≤ 20 ns/100 m - CP 12/1, CP12/2 (EtherCAT) Type C cable a Relevant only for networks with time based synchronization Outer cable diameter Application dependent Wire diameter 1,5 mm ± 0,1 mm Wire cross section AWG 22/x (x: e.g / 19) BS EN 61784-5-12:2012+A1:2015 ≤ 20 ns/100 m Delay scew a Wire diameter 1,5 mm ± 0,1 mm – 14 – IEC 61784-5-12:2012+A1:2015 a Relevant only for networks with time based synchronization ≤ 20 ns/100 m Delay scew a a Relevant only for networks with time based synchronization A.4.4.1.2.2 Copper cables for non Ethernet based CPs Not applicable Copper cables for non Ethernet based CPs A.4.4.1.2.2 Not applicable.Cables for wireless installation A.4.4.1.3 A.4.4.1.4 A.4.4.1.3 Optical fibre cables installation Cables for wireless TableA.6 A.6 provides values based on template the template 61918:2010, Replacement: Replacement: Table provides values based givengiven in in IECIEC 61918:2013 , A.4.4.1.4 Optical fibre cables IEC 61784-5-12:2010/AMD1:2015 – 5on– the Table Table IEC 2015 Replacement: Table A.6 provides values based on the template given in IEC 61918:2010, Table Table A.6 – Information relevant to optical fibre cables Characteristic CharacteristicsTable9 10/125 µm μm 50/125 µmμm 62,5/125 µmμmfibre 980/1 000 50/125 980/1 000 µm μm 10/125 A.6 – Information relevant to62,5/125 optical cables CP 12/1, CP 12/2 single mode multimode step single mode multimode multimode multimode step index index (EtherCAT) silica silica silica POF silica silica silica POF Characteristics 10/125 μm 50/125 μm 62,5/125 μm 980/1 000 μm Standard IEC 60793-2 60793-2 CP 12/1, Attenuation per CP km 12/2 (650 nm) –single mode IEC – 60793-2 multimode IEC–60793-2 multimode IEC index ≤ step 160 dB/km (EtherCAT) silica silica silica POF Attenuation per km – – – Attenuation per km (820 nm) – – – – ≤ 160 dB (650 nm) Attenuation per km (650 nm) – – – ≤ 160 dB/km Attenuation per km (1 310 ≤ 0,5 dB/km ≤ 1,5 dB/km ≤ 1,5 dB/km Attenuation per km km (820 nm) – – – – nm) Attenuation per – – – – (820 nm) Number of optical 0,5 dB/km 1,5 dB/km 1,5 dB/km Attenuation per kmfibres (1 310 ≤ ≤ ≤ Attenuation per km – ≤ 0,5 dB ≤ 1,5 dB ≤ 1,5 dB nm) Connector SC-RJ, SC-RJ, SC-RJ, SC-RJ, (1 310 nm) type (duplex SC SC SC SC Number or of simplex) optical fibres Duplex Duplex Duplex Duplex Number of optical fibres 2 2 Jacket colour requirements -SC-RJ, Connector type SC-RJ, SC-RJ, SC-RJ, Jacket – – – (duplexcolour or simplex) SC –Duplex SC Duplex SC Duplex SC Duplex Jacket material requirements Jacket colour requirements Application dependent Resistance to harsh Jacket material – – – – environment (e.g UV, oil Jacket material Application Application Application Application Resistance to harsh resist, LS0H) dependent dependent dependent dependent environment UV, oil Application dependent Resistance to(e.g harsh Breakout Yes Yes Yes Yes resist, LS0H)(e.g UV, oil environment resist, LS0H) Connector type SC-RJ, SC-RJ, SC-RJ, SC-RJ, (duplex SC Duplex SC SC SC Duplex Breakoutor simplex) Yes YesDuplex YesDuplex Yes A.4.4.1.5 A.4.4.1.6 A.4.4.2.2 A.4.4.1.5 Special purpose balanced and optical fibre cables µm step 200/230 μm index hard clad silica 200/230 μm step index hard clad ≤IEC 10 60793-2 dB/km silica ≤ 10 dB – ≤ 10 dB/km – – – SC-RJ, SC Duplex SC-RJ, – SC Duplex – Application dependent Yes SC-RJ, Yes SC Duplex Specificpurpose requirements CPs Connecting hardware for for balanced cabling CPscables based on Ethernet Special balanced and optical fibre Not applicable Replace the existing Table A.7 with thefor following Table A.7: A.4.4.1.6 Specific requirements CPs Not applicable A.4.4.1.7 Specific requirements for generic cabling cabling CPs in accordance with Table A.7 – Connectors for balanced based on Ethernet ISO/IEC 24702 b A.4.4.1.7 Specific requirements for generic cabling in accordance with IEC 61076-3-117 IEC 61076IEC 61076A.4.4.2 Connecting hardware selection a 2-101 2-109 IEC 60603-724702 series IEC 61076-3-106 b ISO/IEC BS EN 61784-5-12:2012 shielded unshielded Var Var Var 14 M12-4 with M12-8 with 61784-5-12 Connecting © IEC:2010(E) A.4.4.2 hardware selection– 15 – D-coding X-coding CP 12/1, IEC 60603CP 12/2 7-3 A.4.4.2.1 Common No description No No No Yes Yes a For IEC 60603-7 series, the connector selection is based on cabling the desiredCPs channel performance A.4.4.2.2 Connecting hardware for balanced based on Ethernet b Housings to protect connectors Replacement: Table the template given in IEC 61918:2010, 61918:2013 , Table Table A.7 A.7provides providesvalues valuesbased basedonon the template given in IEC Table 7 A.4.4.2.5 Connecting hardware for optical fibre cabling Table A.7 Connectors Add the following text–and Table A.9:for balanced cabling CPs based on Ethernet Addition: IEC 60603-7-x a IEC 61076-3-106 b IEC 61076-3-117 b IEC 61076-2-101 M12-4 with Table A.9 provides values based on the template given in IEC 61918:2013, Table 10 CP 12/1, CP 12/2 (EtherCAT) a (shielded) (unshielded) Variant IEC 606037-3 No No Variant No Variant 14 No D-coding Yes Connector type (duplex or simplex) SC-RJ, SC-RJ, fibre cables SC-RJ, SC-RJ, Table A.6SC-RJ, – Information relevant to optical SC Duplex SC Duplex SC Duplex SC Duplex SC Duplex A.4.4.2.2 Connecting hardware for balanced cabling CPs based on Ethernet EN 61784-5-12:2012+A1:2015 Characteristic 10/125 µm 50/125 µm 62,5/125 µm BS 980/1 000 µm 200/230 µm step single mode multimode multimode step index index hard clad – 15 – IEC 61784-5-12:2012+A1:2015 Replacement: A.4.4.2.2 Connecting hardware for balanced cabling on Ethernet silica silica silica silicaCPs basedPOF Standard IEC 60793-2 IEC 60793-2 IEC 60793-2 IEC 60793-2 IEC 60793-2 ≤ 160 dB ≤ 10 dB Table A.7 provides values based on the IEC 61918:2010, Table Replace the existing Table A.7 with thetemplate followinggiven TableinA.7: Attenuation per km (650 nm) – Attenuation per km (820 nm) – – – Table TableA.7 A.7– –Connectors Connectorsfor forbalanced balancedcabling cablingCPs CPsbased basedon onEthernet Ethernet – – – – b IEC 61076-3-106IEC 61076-3-117 IEC 61076-3-117 IEC 61076IEC 61076IEC 61076-2-101 b 2-109 IEC≤61076-3-106 b – 2-101 – 1,5 dB b ≤ 1,5 dB IEC 60603-7-x a IEC 60603-7a series Attenuation per km ≤ 0,5 dB (1 310 nm) shielded unshielded Var Var Var 14 M12-4 with M12-8 M12-4 with with X-coding (shielded) (unshielded) Variant Variant Variant 14 D-coding D-coding Number of optical fibres 2 CP No NoNo No Yes CP12/1, 12/1, IEC6060360603No No Yes Jacket colour IEC – – – No – –Yes CP CP12/2 12/2 7-37-3 requirements (EtherCAT) a Formaterial Jacket – – – – IEC 60603-7 series, the connector selection–is based on the desired channel performance a For IEC 60603-7-x, the connector selection is based on the desired channel performance Application Application Application Application Application Resistance to harsh b Housings to protect connectors dependent dependent dependent dependent dependent environment UV, oil b Housings to(e.g protect connectors resist, LS0H) Connector type SC-RJ, A.4.4.2.5 ConnectingSC hardware (duplex or simplex) Duplex SC-RJ, SC-RJ, SC-RJ, SC-RJ, forSC optical cabling Duplex fibre SC Duplex SC Duplex SC Duplex A.4.4.2.3 Connecting hardware for copper cabling CPs not based on Ethernet Add the following text and Table A.9: Not applicable A.4.4.2.2 Connecting hardware for balanced cabling CPs based on Ethernet Addition: A.4.4.2.4the existing Connecting forfollowing wirelessTable installation Replace Table hardware A.7 with the A.7: Table A.9 provides valueshardware based on for the optical template given in IEC 61918:2013, Table 10 Connecting fibre cabling A.4.4.2.5 Table A.7 – Connectors for balanced cabling CPs based on Ethernet Replacement: IEC 60603-7 series a IEC 61076-3-106 b IEC 61076-3-117 b IEC 610762-101 IEC 610762-109 M12-4 with D-coding M12-8 with X-coding Table A.8 A.8provides providesvalues valuesbased basedonon the template given in IEC Table 9 Table the template given in IEC 61918:2010, 61918:2013 , Table shielded b Var Var Var 14 Table A.8 – Optical fibre connecting hardware CP 12/1, CP 12/2 a unshielded IEC 60603No No No No Yes 7-3 IEC 61754-2 IEC 61754-4 IEC 61754-24 IEC 61754-20 IEC 61754-22 For IEC 60603-7 series, the connector selection is based on the desired channel performance BFOC/2,5 Housings to protect connectors CP 12/1, No Yes CP 12/2 (EtherCAT) A.4.4.2.5 SC SC-RJ Yes LC No Yes Others F-SMA No No Connecting hardware for optical fibre cabling NOTE IEC 61754 series defines the optical fibre connector mechanical interfaces; performance specifications for optical fibre connectors terminated to specific fibre types are standardised in the IEC 61753 series Add the following text and Table A.9: Addition: A.4.4.2.6 Specific requirements for CPs –6– IEC 61784-5-12:2010/AMD1:2015 Table A.9 provides values based on the template given in IEC 61918:2013, Table 10 Not applicable IEC 2015 Table A.9 – Relationship between FOC and fibre types (CP 12/1 and A.4.4.2.7 Specific requirements for generic cabling in accordance withCP 12/2) ISO/IEC 24702 A.4.4.3 Fibre type Connections within a channel/permanent link000 µm 10/125 62,5/125 µm 980/1 50/125 µm µm single Terminators mode silica multimode silica multimode silica step index POF 200/230 µm step index hard clad silica Others – – – – – – Yes Yes Yes Yes Yes – Yes Yes Yes Yes Yes – LC – – – – – – F-SMA – – – – – – FOC A.4.4.4 Not applicable BFOC/2,5 SC A.4.4.5 SC-RJ Device location and connection _ CP 12/1, No Yes CP EN 12/261784-5-12:2012+A1:2015 BS (EtherCAT) IEC 61784-5-12:2012+A1:2015 Yes No No No – 16 – NOTE IEC 61754 series defines the optical fibre connector mechanical interfaces; performance specifications for optical fibre connectors terminated to specific fibre types are standardised in the IEC 61753 series A.4.4.2.6 Specific requirements for CPs Not applicable A.4.4.2.7 Specific requirements for generic cabling in accordance with ISO/IEC 24702 A.4.4.3 Connections within a channel/permanent link A.4.4.4 Terminators Not applicable – 16 – Device location and connection A.4.4.5 A.4.4.5.1 Common description A.4.4.5.2 Specific requirements for CPs BS EN 61784-5-12:2012 61784-5-12 © IEC:2010(E) Not applicable A.4.4.5.3 Specific requirements for wireless installation A.4.4.5.4 Specific requirements for generic cabling in accordance with ISO/IEC 24702 A.4.4.6 Coding and labelling A.4.4.7 Earthing and bonding of equipment and devices and shield cabling A.4.4.8 Storage and transportation of cables A.4.4.9 Routing of cables A.4.4.10 Separation of circuit Addition: This subclause principle ThisThis means that CP12/1 and CP12/2 networksnetworks work properly subclauseapplies appliesin in principle means that CP12/1 and CP12/2 work while ensuring distances of Table 16ofprovided in provided IEC 61918:2013 properly while the ensuring the distances Table 16 in IEC 61918:2010 A.4.4.11 Mechanical protection of cabling components A.4.4.11.1 Common description A.4.4.11.2 Specific requirements for CPs Not applicable A.4.4.11.3 A.4.4.12 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Installation in special areas A.4.4.12.1 Common description A.4.4.12.2 Specific requirements for CPs Not applicable A.4.4.12.3 Specific requirements for generic cabling in accordance with ISO/IEC 24702 A.4.5 Cabling planning documentation A.4.6 Verification of cabling planning specification A.4.4.12 Installation in special areas A.4.4.12.1 A.4.4.12.2 Common description – 17 – Specific requirements for CPs BS EN 61784-5-12:2012+A1:2015 IEC 61784-5-12:2012+A1:2015 Not applicable A.4.4.12.3 Specific requirements for generic cabling in accordance with ISO/IEC 24702 A.4.5 Cabling planning documentation A.4.6 Verification of cabling planning specification A.5 Installation implementation A.5.1 General requirements A.5.2 Cable installation A.5.2.1 General requirements for all cabling types BS EN 61784-5-12:2012 61784-5-12 © IEC:2010(E) – 17 – A.5.2.2 Installation and routing A.5.2.3 Specific cable installation requirements for CPs Not applicable A.5.2.4 Specific requirements for wireless installation A.5.2.5 Specific requirements for generic cabling in accordance with ISO/IEC 24702 A.5.3 Connector installation A.5.3.1 Common description A.5.3.2 Shielded connectors A.5.3.3 Unshielded connectors A.5.3.4 Specific requirements for CPs Not applicable A.5.3.5 A.5.4 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Terminator installation Not applicable A.5.5 Device installation A.5.5.1 Common description A.5.5.2 Specific requirements for CPs Not applicable A.5.6 Coding and labelling A.5.6.1 Common description A.5.6.2 Specific requirements for CPs Not applicable A.5.7 Earthing and bonding of equipment and devices and shield cabling Subclause 5.7.5 is not applicable A.5.8 As-implemented cabling documentation Not applicable BS EN 61784-5-12:2012+A1:2015 – 18 – IEC 61784-5-12:2012+A1:2015 A.5.7 Earthing and bonding of equipment and devices and shield cabling Subclause 5.7.5 is not applicable A.5.8 A.6 As-implemented cabling documentation Installation verification and installation acceptance test A.6.1 Introduction A.6.2 Installation verification A.6.2.1 General A.6.2.2 Verification according to cabling planning documentation BS EN 61784-5-12:2012 – 18 – 61784-5-12 © IEC:2010(E) Verification of earthing and bonding A.6.2.3 A.6.2.3.1 General A.6.2.3.2 Specific requirements for earthing and bonding Not applicable A.6.2.4 Verification of shield termination A.6.2.5 Verification of cabling system A.6.2.6 Cable selection verification A.6.2.6.1 Common description A.6.2.6.2 Specific requirements for CPs Not applicable A.6.2.6.3 Specific requirements for wireless installation A.6.2.7 Connector verification A.6.2.7.1 Common description A.6.2.7.2 Specific requirements for CPs Not applicable A.6.2.7.3 Specific requirements for wireless installation A.6.2.8 Connection verification A.6.2.8.1 Common description A.6.2.8.2 Number of connections and connectors A.6.2.8.3 Wire mapping A.6.2.9 Terminators verification Not applicable A.6.2.10 Coding and labelling verification A.6.2.10.1 Common description A.6.2.10.2 Specific coding and labelling verification requirements Not applicable A.6.2.11 A.6.3 Verification report Installation acceptance test A.6.2.10 Coding and labelling verification A.6.2.10.1 A.6.2.10.2 Common description BS EN 61784-5-12:2012+A1:2015 – 19 – IEC 61784-5-12:2012+A1:2015 Specific coding and labelling verification requirements Not applicable A.6.2.11 A.6.3 Verification report Installation acceptance test A.6.3.1 General BS EN 61784-5-12:2012 61784-5-12 © IEC:2010(E) – 19 –cabling A.6.3.2 Acceptance test of Ethernet based A.6.3.2.1 Validation of balanced cabling for CPs based on Ethernet A.6.3.2.1.1 Common description A.6.3.2.1.2 Transmission performance test parameters A.6.3.2.1.3 Specific requirements for CPs based on Ethernet Not applicable A.6.3.2.2 Validation of optical fibre cabling for CPs based on Ethernet A.6.3.2.2.1 Common description A.6.3.2.2.2 Specific requirements for optical fibre cabling CPs Not applicable A.6.3.2.3 A.6.3.3 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Acceptance test of non Ethernet based cabling Not applicable A.6.3.4 Specific requirements for wireless installation A.6.3.5 Acceptance test report A.7 Installation administration Subclause 7.8 is not applicable A.8 Installation maintenance and installation troubleshooting Subclause 8.4 is not applicable _ This page deliberately left blank This page deliberately left blank NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards Institution (BSI) BSI is the national body responsible for preparing British Standards and other standards-related publications, information and services BSI is incorporated by Royal Charter British Standards and other standardization products are published by BSI Standards Limited About us Revisions We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions Our British Standards and other publications are updated by amendment or revision The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process Organizations of all sizes and across all sectors choose standards to help them achieve their goals Information on standards We can provide you with the knowledge that your organization needs to succeed Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop, where hard copies can also be purchased If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team Subscriptions Our range of subscription services are designed to make using standards easier for you For further information on our subscription products go to bsigroup.com/subscriptions With British Standards Online (BSOL) you’ll have instant access to over 55,000 British and adopted European and international standards from your desktop It’s available 24/7 and is refreshed daily so you’ll always be up to date You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member PLUS is an updating service exclusive to BSI Subscribing Members You will automatically receive the latest hard copy of your standards when they’re revised or replaced To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit bsigroup.com/shop With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet Licences can cover as few or as many users as you wish With updates supplied as soon as they’re available, you can be sure your documentation is current For further information, email bsmusales@bsigroup.com BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK We continually improve the quality of our products and services to benefit your business If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI Details and advice can be obtained from the Copyright & Licensing Department Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): orders@bsigroup.com Email (enquiries): cservices@bsigroup.com Subscriptions Tel: +44 845 086 9001 Email: subscriptions@bsigroup.com Knowledge Centre Tel: +44 20 8996 7004 Email: knowledgecentre@bsigroup.com Copyright & Licensing Tel: +44 20 8996 7070 Email: copyright@bsigroup.com