30166778 pdf BSI Standards Publication Fibre optic interconnecting devices and passive components — Fibre optic connector interfaces — Part 24 11 Type SC RJ connectors with protective housings based o[.]
BS EN 61754-24-11:2009 BSI Standards Publication Fibre optic interconnecting devices and passive components — Fibre optic connector interfaces — Part 24-11: Type SC-RJ connectors with protective housings based on IEC 61076-3-117 BRITISH STANDARD BS EN 61754-24-11:2009 National foreword This British Standard is the UK implementation of EN 61754-24-11:2009 It is identical to IEC 61754-24-11:2009 The UK participation in its preparation was entrusted by Technical Committee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre optic interconnecting devices and passive components A list of organizations represented on this committee can be obtained on request to its secretary This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application © BSI 2009 ISBN 978 580 52978 ICS 33.180.20 Compliance with a British Standard cannot confer immunity from legal obligations This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2009 Amendments issued since publication Amd No Date Text affected BS EN 61754-24-11:2009 EN 61754-24-11 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM September 2009 ICS 33.180.20 English version Fibre optic interconnecting devices and passive components Fibre optic connector interfaces Part 24-11: Type SC-RJ connectors with protective housings based on IEC 61076-3-117 (IEC 61754-24-11:2009) Dispositifs d’interconnexion et composants passifs fibres optiques Interfaces de connecteurs pour fibres optiques Partie 24-11: Connecteurs de type SC-RJ munis de capots de protection, basés sur la CEI 61076-3-117 (CEI 61754-24-11:2009) Lichtwellenleiter Verbindungselemente und passive Bauteile Steckgesichter von Lichtwellenleiter-Steckverbindern Teil 24-11: Steckverbinderfamilie der Bauart SC-RJ mit Schutzgehäuse nach IEC 61076-3-117 (IEC 61754-24-11:2009) This European Standard was approved by CENELEC on 2009-07-01 CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung Central Secretariat: Avenue Marnix 17, B - 1000 Brussels © 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members Ref No EN 61754-24-11:2009 E BS EN 61754-24-11:2009 -2- EN 61754-24-11:2009 Foreword The text of document 86B/2836/FDIS, future edition of IEC 61754-24-11, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61754-24-11 on 2009-07-01 The following dates were fixed: – latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2010-04-01 – latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2012-07-01 Annex ZA has been added by CENELEC Endorsement notice The text of the International Standard IEC 61754-24-11:2009 was approved by CENELEC as a European Standard without any modification In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60603-7 NOTE Harmonized in EN 60603-7 series (not modified) IEC 61076-3-106 NOTE Harmonized as EN 61076-3-106:2006 (not modified) IEC 61754-1 NOTE Harmonized as EN 61754-1:1997 (not modified) IEC 61755-1 NOTE Harmonized as EN 61755-1:2006 (not modified) ISO 5456-2 NOTE Harmonized as EN ISO 5456-2:1999 (not modified) BS EN 61754-24-11:2009 EN 61754-24-11:2009 -3- Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies Publication Year Title EN/HD Year Degrees of protection provided by enclosures (IP Code) EN 60529 + corr May 1991 1993 2) EN 61076-3-117 2009 2) IEC 60529 - 1) IEC 61076-3-117 - 1) Connectors for electronic equipment Product requirements Part 3-117: Rectangular connectors - Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface - Variant 14 related to IEC 61076-3-106 - Push pull coupling IEC 61753-1 - 1) Fibre optic interconnecting devices and EN 61753-1 passive components performance standard Part 1: General and guidance for performance standards 2007 2) IEC 61754-4 - 1) Fibre optic connector interfaces Part 4: Type SC connector family EN 61754-4 1997 2) IEC 61754-24 - 3) Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces Part 24: Type SC-RJ connector family EN 61754-24 200X IEC 61755 Series Fibre optic connector optical interfaces EN 61755 Series 1) 2) 3) Undated reference Valid edition at date of issue At draft stage 3) –2– BS EN 61754-24-11:2009 61754-24-11 IEC:2009(E) CONTENTS FOREWORD Scope .5 Normative references Description .5 3.1 General 3.2 Functional requirements 3.3 Environmental, optical and mechanical requirements .6 Interface 4.1 Free connector part 4.2 Active device receptacle part 4.3 Mounting information for the active device receptacle .9 Bibliography 11 Figure – Free connector part (male) .7 Figure – Active device receptacle Figure – Mounting information of the active device receptacle .9 Table – Intermateability between plugs, adaptors and receptacles Table – Dimensions of the free connector .8 Table – Dimensions of the active device receptacle Table – Dimensions for mounting the active device receptacle 10 BS EN 61754-24-11:2009 61754-24-11 IEC:2009(E) –3– INTERNATIONAL ELECTROTECHNICAL COMMISSION FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS – FIBRE OPTIC CONNECTOR INTERFACES – Part 24-11: Type SC-RJ connectors with protective housings based on IEC 61076-3-117 FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees) The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”) Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication 6) All users should ensure that they have the latest edition of this publication 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications 8) Attention is drawn to the Normative references cited in this publication Use of the referenced publications is indispensable for the correct application of this publication 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights IEC shall not be held responsible for identifying any or all such patent rights International Standard IEC 61754-24-11 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics The text of this standard is based on the following documents: FDIS Report on voting 86B/2836/FDIS 86B/2877/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table This publication has been drafted in accordance with the ISO/IEC Directives, Part –4– BS EN 61754-24-11:2009 61754-24-11 IEC:2009(E) A list of all the parts in the IEC 61754 series, under the general title Fibre optic interconnecting devices and passive components – Fibre optic connector interfaces, can be found on the IEC website Future standards in this series will carry the new general title as cited above Titles of existing standards in this series will be updated at the time of the next edition The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication At this date, the publication will be • • • • reconfirmed, withdrawn, replaced by a revised edition, or amended A bilingual version of this publication may be issued at a later date BS EN 61754-24-11:2009 61754-24-11 IEC:2009(E) –5– FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS – FIBRE OPTIC CONNECTOR INTERFACES – Part 24-11: Type SC-RJ connectors with protective housings based on IEC 61076-3-117 Scope This part of IEC 61754 serves as an interface standard and describes an SC-RJ fibre optic connector equipped with a protective housing for upgrading the existing interface described in IEC 61754-24 to IP65 and IP67 ratings according to IEC 60529, for use in harsh industrial environments Normative references The following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of thereferenced document (including any amendments) applies IEC 60529, Degrees of protection provided by enclosures (IP Code) IEC 61076-3-117, Connectors for electronic equipment – Product requirements – Part 3-117: Rectangular connectors – Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface – Variant 14 related to IEC 61076-3-106 – Push-pull coupling IEC 61753-1, Fibre optic interconnecting devices and passive components performance standard – Part 1: General and guidance for performance standards IEC 61754-4, Fibre optic connector interfaces – Part 4: Type SC connector family IEC 61754-24, Fibre optic interconnecting devices and passive components – Fibre optic connector interfaces – Part 24: Type SC-RJ connector family IEC 61755 (all parts), Fibre optical connector optical interfaces Description 3.1 General IEC 61754-24-11, which is an interface standard, based on IEC 61754-24 describes protective housing for fibre optic connectors for use in harsh industrial environments The fully assembled connector incorporates fixed and free connectors which are fully compliant with IEC 61754-24 The mechanical design of the interior allows the mounting of connectors according to IEC 61754-24 _ To be published BS EN 61754-24-11:2009 61754-24-11 IEC:2009(E) –6– This standard is applied the same optical fibres listed in IEC 61754-24 with their various fibre capacities, types and designs The intermateability between plugs, adaptors and receptacles are given below in Table Table – Intermateability between plugs, adaptors and receptacles Adaptors/active device receptacles interfaces Plugs 61754-24-11 61754-24 (duplex) 61754-4 (simplex) 61754-24-11 Mate (with sealing) Not mate Not mate 61754-24 (duplex) Mate (without sealing) Mate Not mate 61754-4 (simplex) Mate (without sealing) Mate Mate 3.2 Functional requirements The general function of the protective housing according to this standard is to provide: a) a ruggedised housing for fibre optic connectors; b) a cable management system for the external input and output cables; c) a mateable connection between two or more optical fibres, where an optical connector is enclosed by a protective housing; d) to ensure the correct functioning of the fibre optic connection under the specified environmental and mechanical conditions 3.3 Environmental, optical and mechanical requirements The optical performance requirements are given in the IEC 61755 series Performance tests according to IEC 61753-1 shall be carried out for the chosen performance category If not covered in the chosen performance category, a test according to IEC 60529 for an IP67 grade shall additionally be performed Interface 4.1 Free connector part Figure and Table specify the outline and dimensions of the free connector NOTE Figure uses scheme from ISO 5456-2 BS EN 61754-24-11:2009 61754-24-11 IEC:2009(E) –7– BA BB B BO BD BP B BE BF BG BH BL Detail BK :1 Detail B-B BN BC BJ BI IEC 978/09 Figure – Free connector part (male) BS EN 61754-24-11:2009 61754-24-11 IEC:2009(E) –8– Table – Dimensions of the free connector Reference Maximum Minimum Nominal BA 22,8 mm BB 18,09 mm 18,03 mm 18,06 mm BC 21,9 mm 21,7 mm 21,8 mm BD 20,55 mm 20,45 mm 20,5 mm BE 5,75 mm 5,45 mm 5,6 mm BF 15,35 mm 15,05 mm 15,2 mm BG 17,8 mm 17,4 mm 17,6 mm BH 20,6 mm 20,4 mm 20,5 mm BI 2,73 mm 2,67 mm BJ 1,47 mm 1,37 mm BK R 2,7 mm 1,42 mm 1,2 mm BL 18,5 mm BN 27,4 mm BO 18,09 mm 18,4 mm 18,45 mm 18,03 mm 18,06 mm BP 4.2 30° Active device receptacle part Figure and Table specify the outline and dimensions of the active device receptacle NOTE Figure uses scheme from ISO 5456-2 AA AB AC AV AU Mechanical reference plane A X AJ AK AW AD X AI A-A AE AF AR AX AS AT AM AO AN Flat seal A AP AQ AG AH IEC 979/09 Figure – Active device receptacle BS EN 61754-24-11:2009 61754-24-11 IEC:2009(E) –9– Table – Dimensions of the active device receptacle Maximum Minimum Nominal AA 14,85 mm 14,75 mm 14,8 mm AB 6,05 mm 5,95 mm mm AC 1,7 mm 1,3 mm 1,5 mm Reference AD 31° 29° 30° AE 2,1 mm 1,9 mm R mm AF 2,83 mm 2,77 mm R 2,8 mm AG 18,23 mm 18,17 mm 18,2 mm AH 20,3 mm 20,1 mm 20,2 mm AI 0,7 mm 0,6 mm 0,65 mm AJ 1,95 mm 1,85 mm 1,9 mm AK 0,65 mm 0,55 mm 0,6 mm AN 5,1 mm 4,9 mm R mm AO 2,1 mm 1,9 mm mm AM R 0,4 mm AP mm AQ 8,35 mm 8,3 mm AR 21,7 mm 21,45 mm 21,5 mm AS 18,23 mm 18,17 mm 18,2 mm AT 1,47 mm 1,37 mm AU 13 mm AV AW 7,1 mm 16 mm AX 4.3 8,25 mm 12,8 mm 12,8 mm 6,9 mm mm 14 mm 8,2 mm 1,42 mm 15° 8,1 mm 8,15 mm Mounting information for the active device receptacle Following Figure and Table specify the outline and dimensions of the cutout for the active device receptacle CC CB CA CE CD IEC 980/09 Figure – Mounting information of the active device receptacle BS EN 61754-24-11:2009 61754-24-11 IEC:2009(E) – 10 – Table – Dimensions for mounting the active device receptacle Reference Maximum mm Minimum mm CA 33,1 32,9 33 CB 22,9 22,5 22,7 CC Nominal mm M3 CD 19,3 CE R 1,25 19,1 19,2 BS EN 61754-24-11:2009 61754-24-11 IEC:2009(E) – 11 – Bibliography IEC 60603-7(all parts), Connectors for electronic equipment IEC 61076-3-106, Connectors for electronic equipment – Product requirements – Part 3-106: Rectangular connectors – Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface IEC 61754-1, Fibre optic connector interfaces – Part 1: General and guidance IEC 61755-1, Fibre optic connector optical interfaces – Part 1: Optical interfaces for single mode non - dispersion shifted fibres – General and guidance ISO 5456-2: Technical drawings – Projection methods – Part 2: Orthographic representations _ This page deliberately left blank This page deliberately left blank NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards Institution (BSI) BSI is the national body responsible for preparing British Standards and other standards-related publications, information and services BSI is incorporated by Royal Charter British Standards and other standardization products are published by BSI Standards Limited About us Revisions We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions Our British Standards and other publications are updated by amendment or revision The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process Organizations of all sizes and across all sectors choose standards to help them achieve their goals Information on standards We can provide you with the knowledge that your organization needs to succeed Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop, where hard copies can also be purchased If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team Subscriptions Our range of subscription services are designed to make using standards easier for you For further information on our subscription products go to bsigroup.com/subscriptions With British Standards Online (BSOL) you’ll have instant access to over 55,000 British and adopted European and international standards from your desktop It’s available 24/7 and is refreshed daily so you’ll always be up to date You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member PLUS is an updating service exclusive to BSI Subscribing Members You will automatically receive the latest hard copy of your standards when they’re revised or replaced To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit bsigroup.com/shop With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet Licences can cover as few or as many users as you wish With updates supplied as soon as they’re available, you can be sure your documentation is current For further information, email bsmusales@bsigroup.com BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK We continually improve the quality of our products and services to benefit your business If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI Details and advice can be obtained from the Copyright & Licensing Department Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): orders@bsigroup.com Email (enquiries): cservices@bsigroup.com Subscriptions Tel: +44 845 086 9001 Email: subscriptions@bsigroup.com Knowledge Centre Tel: +44 20 8996 7004 Email: knowledgecentre@bsigroup.com Copyright & Licensing Tel: +44 20 8996 7070 Email: copyright@bsigroup.com