BRITISH STANDARD Pressure sensitive adhesive tapes for electrical purposes Part 3 Specifications for individual materials Sheet 5 Cellulosic paper, non creped, with rubber thermosetting adhesive The E[.]
BS EN 604543-5:1998 IEC 60454-3-5:1998 BRITISH STANDARD Pressure-sensitive adhesive tapes for electrical purposes Part 3: Specifications for individual materials - Sheet 5: Cellulosic paper, non-creped, with rubber thermosetting adhesive The European Standard EN 60454551998 has the status of a British Standard ICs 29.036.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW ``````-`-`,,`,,`,`,,` - Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELEC No reproduction or networking permitted without license from IHS Not for Resale BS EN 604543-5~1998 National foreword This British Standard is the English language version of EN 60454351998 It is identical with IEC W 9 The UK participation in its preparation was entrusted by Technical Committee GELJ15, Insulating materials, to Subcommittee GELJl5A3, Materiai specifications, which has the responsibfity to: - aid enquirem to understand the text; - present to the responsible internationaH3mpean committee any enquiries on the interpretation, or proposals for change, and keep the UK inkrests informed - monitor related international and European developments and promuigate them in the UK A list of organhations represented on this subcommittee can be obtained on request to its secretary From 1January 1997, ail IEC publications have the number 60000 added to the old number For instance, IEC 27-1 has been renumbered as IEC 60027-1 For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems NOTE BS 3924 1978, Specification for pressure-sensitive adhesive tapes for electrical insulating purposes, will be withdrawn after Sheets to 19 (inclusive) of BS EN 60454-3 have been published Cross-references ``````-`-`,,`,,`,`,,` - Attention is drawn to the fact that CEN and CENELEC standards normally include an annex which lists normative references to i n t e d o n a l publications with their corresponding European publications The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled ?International Standards Correspondence Index?, or by using the ?Find?facility of the BSI Standards Electronic Catalogue A British Standard does not purport to include all the necessary provisions of a contract Users of British Standards are responsible for their correct application Compliance with a British Standard does not of itself confer immunity from legal obligations Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages to and a back cover This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 October 1998 Amd No Date Text affected O BSI 1998 ISBN O 680 30063 Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELEC No reproduction or networking permitted without license from IHS Not for Resale EN 60454-3-5 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHENORM April 1998 ICs 29.035.10 Descriptors: Solid electrical insulating materials, adhesoda tapes paper cellulose, thermosetting resins, rubber, designation, characteristics, tests, marking English version Pressure-sensitive adhesive tapes for electrical purposes Part 3: Specifications for individual materials Sheet 5: Cellulosic paper, non-creped, with rubber thermosetting adhesive (IEC 60454-3-5:1998) Rubans adhésifs sensibles la pression usages électriques Partie 3: Spécifications pour matériaux particuliers Feuille 5: Papier cellulosique non crêpé avec un adhésif en caoutchouc thermodurcissable (CE1 - - : 9 ) Selbstklebende Bänder für elektrotechnische Anwendungen Teil 3: Bestimmungen für einzelne Materialien Blatt 5: Anforderungen für Bänder aus nicht-gekrepptem Zellulosepapier mit wärmehärtendem Kautschuk-Klebestoff (IEC 60454-3-5: 9 ) This European Standard was approved by CENELEC on 1998-04-01 CENELEC members are bound t o comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application t o the Central Secretariat or t o any CENELEC member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CENELEC member into its o w n language and notified t o the Central Secretariat has the same status as the official versions CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom CENELEC European C o m m i t t e e f o r Electrotechnical Standardization C o m i t é Européen de Normalisation Electrotechnique Europäisches Komitee f ü r Elektrotechnische N o r m u n g Central Secretariat: rue de Stassarỵ 35, B - 1050 Brussels 1998 CENELEC - Ali rights of exploitation in any form and by any means reserved worldwide for CENELEC members R e f No EN 60453-3-5:1998 E ``````-`-`,,`,,`,`,,` - Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELEC No reproduction or networking permitted without license from IHS Not for Resale ~~ ~ STD.BSI = lb24bbỵ ~~ 1998 BS EN bUq59-3-5-ENGL 0725b33 bbq Page EN 60454-3-5:1998 Foreword The text of document 15C/855/FDIS, future edition of IEC 60454-3-5, prepared by SC 15C, Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60454-3-5 on 1998-04-01 The following dates were fixed: - latest date by which the EN has t o be implemented - at national level by publication of an identical national standard or by endorsement (dop) 1999-01-01 latest date by which the national standards conflicting with the EN have t o be withdrawn (dow) 200 1-01-01 Annexes designated "normative" are part of the body of the standard In this standard, annex ZA is normative Annex ZA has been added by CENELEC Endorsement notice The t e x t of the International Standard IEC 60454-3-5:1998 was approved by CENELEC as a European Standard without any modification ``````-`-`,,`,,`,`,,` - Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELEC No reproduction or networking permitted without license from IHS Not for Resale ~ = lb24bb7 ~ STD.BS1 BS E N b045Ll-3-5-ENGL 1778 ~~ 0725b34 T m Page EN 60454-3-5:1998 INTRODUCTION This International Standard is one of a series which deals with pressure-sensitive adhesive tapes, intended primarily for electrical purposes The series consists of three parts: - Part 1: General requirements (IEC 60454-1); - Part 2: Methods of test (IEC 60454-2); - Part 3: Specifications for individual materials (IEC 60454-3) This standard contains one of the sheets comprising part as follows: ``````-`-`,,`,,`,`,,` - Sheet 5: Cellulosic paper, non-creped, with rubber thermosetting adhesive Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELEC No reproduction or networking permitted without license from IHS Not for Resale ~ ~ STD.BSI B S E N b - - - E N G L L b b b ï 0725b35 43L m ``````-`-`,,`,,`,`,,` - Page 1998 EN 60454-3-5:1998 PRESSURE SENSITIVE ADHESIVE TAPES FOR ELECTRICAL PURPOSES - - Part 3: Specifications for individual materials Sheet 5: Cellulosic paper, non-creped, with rubber thermosetting adhesive General 1.1 Scope This sheet of IEC 60454-3 contains the requirements for pressure-sensitive adhesive tapes made with cellulosic paper, non-creped, with rubber thermosetting adhesive Materials which conform to this specification meet established levels of performance However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application, and not based on this specification alone 1.2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this sheet of IEC 60454-3 At the time of publication, the editions indicated were valid All normative documents are subject to revision and parties to agreements based on this sheet of IEC 60454-3 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated belowl) Members of IEC and I S maintain registers of currently valid International Standards IEC 60426:1973, Test methods for determining electrolytic corrosion with insulating materials IEC 60454-1:1992, Specifications for pressure-sensitive adhesive tapes for electrical purposes Pari 1: General requirements - IEC 60454-2: 1994, Specification for pressure-sensitive adhesive tapes for electrical purposes Pari 2: Methods of test - 1.3 Definitions Refer to IEC 60454-1 for definitions applicable to these materials Classification and designation The products shall be designated for ordering purposes as follows: IEC 60454-3-5/P-C/105/R-T~ In case of dispute, the reference edition is applicable Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELEC No reproduction or networking permitted without license from IHS Not for Resale STD.BS1 B S E N b q - - - E N G L 1778 Lb24bbỵ 0725b3b 378 Page EN 60454-3-5:1998 Requirements 3.1 All applicable requirements of IEC 60454-1 shall apply to material furnished under this specif ¡cation 3.2 The physical and electrical properties of products supplied according to this specification shall be within the limits listed in table when tested in accordance with the test methods listed the rein 3.3 Thermal endurance When required by the purchaser, the manufacturer shall provide evidence that when tested in accordance with clause 21 of IEC 60454-2, the product has a temperature index of not less than 105 The exposure temperatures are 120 OC,140 OC,and 160 OC The end-point criteria used shall be: - for breakdown voltage: 0,5 kV (metal foil electrode), and - for loss of mass: 20 % Test methods All tests shall be conducted in accordance with the appropriate clauses and subclauses of IEC 60454-2 Marking, labelling and packaging Unless otherwise specified, all marking, labelling and packaging shall be in accordance with the requirements of IEC 60454-1 ``````-`-`,,`,,`,`,,` - Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELEC No reproduction or networking permitted without license from IHS Not for Resale S T D - B S I B S EN b0454-3-5-ENGL Lb24bb7 0725b37 204 1778 Page = EN 60454-3-5:1998 Table - Requirements for all types Clause or subclause of IEC 60454-2 Units Requlremento Thickness mm Nominal value per manufacturer 10,025 mm or 115 % whichever is greater Width mm 7.2.1 of IEC 60454-1 Lenath m of IEC 60454-1 Propertles Electrolytic corrosion: - insulation resistance 7.5 i2125 mm width x 10' minimum after 24 h at (23 i 2) "C and (93 f 2) % relative humidity or - visual method Tensile strength Adhesion to steel Bond separation after thermal treatment I 7.6 None Grade shall be at least as good as B (see table I of IEC 60426) N / mm width 50 minimum N A mm width 3.0 minimum passes mm Flagging test: - at curing temperature Condition per 15.5.2 - 12 mm rod - at room temperature Condition per 15.5.1 - 12 mm rod - at room temperature 17 Thermal endurance 21 maximum ``````-`-`,,`,,`,`,,` - Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELEC No reproduction or networking permitted without license from IHS Not for Resale Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications These normative references are cited a t the appropriate places in the text and the publications are listed hereafter For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision For undated references the latest edition of the publication referred t o applies (including amendments) NOTE: When an international publication has been modified by common modifications, indicated by (mod), the relevant ENIHD applies EN/HD Year Specifications for pressure-sensitive adhesive tapes for electrical purposes Part 1: General requirements EN 60454-1 1994 Part 2: Methods of test EN 60454-2 1995 Publication Year - Title IEC 60426 1973 Test methods for determining electrolytic corrosion with insulating materials IEC 60454-1 1992 1994 * m * ``````-`-`,,`,,`,`,,` - Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELEC No reproduction or networking permitted without license from IHS Not for Resale BS EN 60454-3-5:1998 IEC 60454-3-5:1998 BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards It presents the UK view on standards in Europe and at the international level It is incorporated by Royal Charter Revisions British Standards are updated by amendment or revision Users of British Standards should make sure that they possess the latest amendments or editions It is the constant aim of BSI to improve the quahty of our products and services We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover Tel 0181 996 9000 Fax: 0181 996 7400 BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services Tel: 0181 996 7000 Fax: 0181 996 7001 In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service Various BSI electronic information services are also available which give details on all its products and services Contact the Information Centre Tel: 0181 996 7111 Fax: 0181 996 7048 Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards For details of these and other benefits contact Membeiship Administration Tel 0181 996 7002 Fax: 0181 996 7001 Copyright ``````-`-`,,`,,`,`,,` - Copyright subsists in all BSI publications BSI also holds the copyright, in the UK, of the publications of the international standardizationbodies Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI T ~ Ldoes S not preclude the free use, in the c o m e of implementing the standard, of necessary details such as symbols, and size, type or grade designations If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained If permission is granted, the terms may include royalty payments or a licensing agreement Details and advice can be obtained from the Copyright Manager Tel 0181 996 7070 BSI 389 Chiswick High Road London w4 4AL Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELEC No reproduction or networking permitted without license from IHS Not for Resale