000405U001 SUMMARY OF CHANGES The 2007 Edition of this Code contains revisions in addition to the 2004 Edition with 2005 and 2006 Addenda The revisions are identified with the designation 07 in the ma[.]
SUMMARY OF CHANGES The 2007 Edition of this Code contains revisions in addition to the 2004 Edition with 2005 and 2006 Addenda The revisions are identified with the designation 07 in the margin and, as described in the Foreword, become mandatory six months after the publication date of the 2007 Edition To invoke these revisions before their mandatory date, use the designation “2007 Edition” in documentation required by this Code If you choose not to invoke these revisions before their mandatory date, use the designation “2004 Edition through the 2006 Addenda” in documentation required by this Code The BC numbers listed below are explained in more detail in ”List of Changes in BC Order” following this Summary of Changes Changes given below are identified on the pages by a margin note, 07, placed next to the affected area Location Page Change Guideline on the Approval of New Materials xliii–xlvi Revised (BC02-3773) Acceptable ASTM Editions xlvii /lvi Revised in its entirety (BC05-1651) Acceptable Non-ASTM Editions lvii Added (BC02-3773, BC04-1559, BC05-1651) SA-204/SA-204M 319/321 Revised in its entirety (BC04-379) SA-225/SA-225M 357/360 Revised in its entirety (BC04-380) SA-266/SA-266M 433/437 Revised in its entirety (BC05-1285) SA-268/SA-268M 439/447 Revised in its entirety (BC04-977) SA-370 643/700 Revised in its entirety (BC05-1287) SA-376/SA-376M 707/716 Revised in its entirety (BC04-1576) SA-387/SA-387M 717/723 Revised in its entirety (BC05-1456) SA-455/SA-455M 841/843 Revised in its entirety (BC04-386) SA-479/SA-479M 851/861 Revised in its entirety (BC04-1377) SA-508/SA-508M 917/926 Revised in its entirety (BC05-1288) SA-515/SA-515M 953/956 Revised in its entirety (BC04-387) SA-516/SA-516M 957/962 Revised in its entirety (BC04-916) SA-563 1055/1065 Revised in its entirety (BC04-220) SA-649/SA-649M 1173/1177 Revised in its entirety (BC05-1289) SA-666 1191/1200 Revised in its entirety (BC04-1378) SA-736/SA-736M 1311/1315 Revised in its entirety (BC04-389) SA-737/SA-737M 1317/1319 Revised in its entirety (BC04-390) SA-788/SA-788M 1397/1411 Revised in its entirety (BC05-1290) SA-965/SA-965M 1545/1551 Revised in its entirety (BC00-433) SA/AS 1548 1649 Revised in its entirety (BC06-268) SA/CSA-G40.21 1651 Revised in its entirety (BC04-1559, BC06-2681) SA/EN 10020-2 1653 Revised in its entirety (BC06-268) SA/EN 10020-3 1655 Revised in its entirety (BC06-268) SA/JIS G3118 1657 Revised in its entirety (BC06-268) NOTE: Volume 57 of the Interpretations to Section II, Part A of the ASME Boiler and Pressure Vessel Code follows the last page of the Edition to Section II, Part A lxi Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corporate Wide/1000001100 Not for Resale, 08/27/2008 14:20:00 MDT ``,,````,,,,,,`````,```,,,`,``-`-`,,`,,`,`,,` - LIST OF CHANGES IN BC ORDER BC Number Change BC00-433 BC02-3773 Change references to SA-336 for stainless steel forgings to SA-965 Added new paragraph “CEN Specifications” in the Guidelines on the Approval of New Materials Added new General Note in the Guideline on Acceptable Non-ASTM Editions Adopted ASTM A268/A268M-03 edition of A268 as SA-268 ASME SA-479/SA-479M specification updated to later 2004 version of the corresponding ASTM Editorial corrections were made Tensile Strength of 201-1 decreased from 95 to 75 ksi Adopted 2004 version of the CSA G40.21-04 material specification ASME SA-376/SA-376M specification updated to later 2004 version of the corresponding ASTM Editorial corrections were made SA-563 Revised — Later version of ASTM specification adopted Adopted 2003 version of the ASTM A 204 specification Adopted 2003 version of the ASTM Specification A 225/A 225M Adopted 2003 version of ASTM A 455/A 455M Adopted 2003 version of ASTM A 515/A 515M Adopted 2003 version of ASTM A 736/A 736M Adopted 1999 version of ASTM A 737/A 737M ASME SA-516/SA-516M updated to 2006 version of the ASTM A 516/A 516M specification Includes changes through the -06 revision This latest revision reinstates a lost footnote c in Table dealing with manganese levels permitted in thinner Grade 60 material Adopted 2004 version of the ASTM A 268/A 268M specification Adopted 2003a version of the ASTM A 266/A 266M specification Adopted 2005 version of the ASTM A 370 specification Adopted 2005b version of the ASTM A 508/A 508M specification Adopted 2004 version of the ASTM A 649/A 649M specification Adopted 2005c version of the ASTM A 788/A 788M specification ASME SA-376/SA-376M specification updated to later 2006 version of ASTM A 387/A 387M Added new table “Acceptable Non-ASTM Editions.” Revise cover sheets for foreign material specifications to refer to Appendix A on Sources of Standards for organization contact information BC03-1765 BC04-1377 BC04-1378 BC04-1559 BC04-1576 BC04-220 BC04-379 BC04-380 BC04-386 BC04-387 BC04-389 BC04-390 BC04-916 BC04-977 BC05-1285 BC05-1287 BC05-1288 BC05-1289 BC05-1290 BC05-1456 BC05-1651 BC06-268 lxii Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corporate Wide/1000001100 Not for Resale, 08/27/2008 14:20:00 MDT