``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Job #69236 Job #69236 ASME Covers 1&4 Colors 702 Red Black Side Marks Ray Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT A N I N T E R N AT I O N A L CO D E 2007 ASME Boiler & Pressure Vessel Code 2008a Addenda July 1, 2008 II ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - Part A Ferrous Material Specifications (Beginning to SA-450) MATERIALS ASME Boiler and Pressure Vessel Committee Subcommittee on Materials U02AW8 Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT Date of Issuance: July 1, 2008 This international code or standard was developed under procedures accredited as meeting the criteria for American National Standards and it is an American National Standard The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assume any such liability Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals The footnotes in this document are part of this American National Standard The Specifications published and copyrighted by the American Society for Testing and Materials are reproduced with the Society’s permission No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher Library of Congress Catalog Card Number: 56-3934 Printed in the United States of America The American Society of Mechanical Engineers Three Park Avenue, New York, NY 10016-5990 Copyright © 2008 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All rights reserved ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT A N I N T E R N AT I O N A L CO D E 2007 ASME Boiler & Pressure Vessel Code 2007 Edition July 1, 2007 II Part A Ferrous Material Specifications (Beginning to SA-450) MATERIALS ASME Boiler and Pressure Vessel Committee Subcommittee on Materials ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT Date of Issuance: July 1, 2007 (Includes all Addenda dated July 2006 and earlier) This international code or standard was developed under procedures accredited as meeting the criteria for American National Standards and it is an American National Standard The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assume any such liability Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals The footnotes in this document are part of this American National Standard ASME collective membership mark The above ASME symbols are registered in the U.S Patent Office “ASME” is the trademark of the American Society of Mechanical Engineers ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - The Specifications published and copyrighted by the American Society for Testing and Materials are reproduced with the Society’s permission No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher Library of Congress Catalog Card Number: 56-3934 Printed in the United States of America Adopted by the Council of the American Society of Mechanical Engineers, 1914 Revised 1940, 1941, 1943, 1946, 1949, 1952, 1953, 1956, 1959, 1962, 1965, 1968, 1971, 1974, 1977, 1980, 1983, 1986, 1989, 1992, 1995, 1998, 2001, 2004, 2007 The American Society of Mechanical Engineers Three Park Avenue, New York, NY 10016-5990 Copyright © 2007 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT 2007 ASME BOILER AND PRESSURE VESSEL CODE SECTIONS I Rules for Construction of Power Boilers II Materials Part A — Ferrous Material Specifications Part B — Nonferrous Material Specifications Part C — Specifications for Welding Rods, Electrodes, and Filler Metals Part D — Properties (Customary) Part D — Properties (Metric) III Rules for Construction of Nuclear Facility Components Subsection NCA — General Requirements for Division and Division Division Subsection NB — Class Components Subsection NC — Class Components Subsection ND — Class Components Subsection NE — Class MC Components Subsection NF — Supports Subsection NG — Core Support Structures Subsection NH — Class Components in Elevated Temperature Service Appendices Division — Code for Concrete Containments Division — Containments for Transportation and Storage of Spent Nuclear Fuel and High Level Radioactive Material and Waste IV Rules for Construction of Heating Boilers V Nondestructive Examination VI Recommended Rules for the Care and Operation of Heating Boilers VII Recommended Guidelines for the Care of Power Boilers VIII Rules for Construction of Pressure Vessels Division Division — Alternative Rules Division — Alternative Rules for Construction of High Pressure Vessels IX Welding and Brazing Qualifications X Fiber-Reinforced Plastic Pressure Vessels XI Rules for Inservice Inspection of Nuclear Power Plant Components XII Rules for Construction and Continued Service of Transport Tanks iii ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT Interpretations of the Code are distributed annually in July with the issuance of the edition and subsequent addenda Interpretations posted in January at www.cstools.asme.org/interpretations are included in the July distribution ADDENDA Colored-sheet Addenda, which include additions and revisions to individual Sections of the Code, are published annually and will be sent automatically to purchasers of the applicable Sections up to the publication of the 2010 Code The 2007 Code is available only in the loose-leaf format; accordingly, the Addenda will be issued in the loose-leaf, replacement-page format CODE CASES The Boiler and Pressure Vessel Committee meets regularly to consider proposed additions and revisions to the Code and to formulate Cases to clarify the intent of existing requirements or provide, when the need is urgent, rules for materials or constructions not covered by existing Code rules Those Cases that have been adopted will appear in the appropriate 2007 Code Cases book: “Boilers and Pressure Vessels” and “Nuclear Components.” Supplements will be sent automatically to the purchasers of the Code Cases books up to the publication of the 2010 Code INTERPRETATIONS ASME issues written replies to inquiries concerning interpretation of technical aspects of the Code The Interpretations for each individual Section will be published separately and will be included as part of the update service to that Section Interpretations of Section III, Divisions and 2, will be included with the update service to Subsection NCA ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - iv Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT CONTENTS Foreword Statements of Policy Personnel ASTM Personnel Preface Specifications Listed by Materials Specification Removal Guidelines on Submittal of Technical Inquiries to the Boiler and Pressure Vessel Committee Guideline on the Approval of New Materials Under the ASME Boiler and Pressure Vessel Code Guideline on Acceptable ASTM Editions Guideline on Acceptable Non-ASTM Editions Guidelines on Multiple Marking of Materials Summary of Changes List of Changes in BC Order Specifications SA-6/SA-6M SA-20/SA-20M SA-29/SA-29M SA-31 SA-36/SA-36M SA-47/SA-47M SA-53/SA-53M SA-105/SA-105M SA-106 SA-134 SA-135 SA-178/SA-178M SA-179/SA-179M SA-181/SA-181M SA-182/SA-182M SA-192/SA-192M SA-193/SA-193M SA-194/SA-194M SA-202/SA-202M SA-203/SA-203M SA-204/SA-204M General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling General Requirements for Steel Plates for Pressure Vessels General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought and Cold-Finished Steel Rivets and Bars for Rivets, Pressure Vessels Carbon Structural Steel Ferritic Malleable Iron Castings Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless Carbon Steel Forgings for Piping Applications Seamless Carbon Steel Pipe for High-Temperature Service Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over) Electric-Resistance-Welded Steel Pipe Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater Tubes Seamless Cold-Drawn Low-Carbon Steel Heat Exchanger and Condenser Tubes Carbon Steel Forgings, for General-Purpose Piping Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service Seamless Carbon Steel Boiler Tubes for High-Pressure Service Alloy Steel and Stainless Steel Bolting Materials for High-Temperature Service Carbon and Alloy Steel Nuts for Bolts for High-Pressure or HighTemperature Service, or Both Pressure Vessel Plates, Alloy Steel, Chromium-Manganese-Silicon Pressure Vessel Plates, Alloy Steel, Nickel Pressure Vessel Plates, Alloy Steel, Molybdenum ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS v Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT ix xiii xv xxvii xxix xxxi xxxix xli xliii xlvii lvii lix lxi lxii 83 127 153 157 163 171 199 205 221 227 237 243 247 251 271 275 293 311 315 319 SA-209/SA-209M SA-210/SA-210M SA-213/SA-213M SA-214/SA-214M SA-216/SA-216M SA-217/SA-217M SA-225/SA-225M SA-231/ SA-231M SA-232/ SA-232M SA-234/SA-234M SA-240/SA-240M SA-249/SA-249M SA-250/SA-250M SA-263 SA-264 SA-265 SA-266/SA-266M SA-268/SA-268M SA-275/SA-275M SA-276 SA-278 SA-283/SA-283M SA-285/SA-285M SA-299/SA-299M SA-302/SA-302M SA-307 SA-311/SA-311M SA-312/SA-312M SA-320/SA-320M SA-325 SA-333/SA-333M SA-334/SA-334M SA-335/SA-335M SA-336/SA-336M SA-350/SA-350M SA-351/SA-351M Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes Seamless Medium-Carbon Steel Boiler and Superheater Tubes Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and HeatExchanger Tubes Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes Steel Castings, Carbon, Suitable for Fusion Welding for High-Temperature Service Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts Suitable for High-Temperature Service Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-Nickel Chromium-Vanadium Alloy Steel Spring Wire Chromium-Vanadium Alloy Steel Valve Spring Quality Wire Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High-Temperature Service Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater Tubes Stainless Chromium Steel-Clad Plate Stainless Chromium-Nickel Steel-Clad Plate Nickel and Nickel-Base Alloy-Clad Steel Plate Carbon Steel Forgings, for Pressure Vessel Components Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service Magnetic Particle Examination of Steel Forgings Stainless Steel Bars and Shapes Gray Iron Castings for Pressure-Containing Parts for Temperature Up to 650°F Low- and Intermediate Tensile Strength Carbon Steel Plates Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength Pressure Vessel Plates, Carbon Steel, Manganese-Silicon Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-Nickel Carbon Steel Bolts and Studs, 60 000 psi Tensile Strength Cold-Drawn, Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements Seamless and Welded Austenitic Stainless Steel Pipes Alloy Steel Bolting Materials for Low-Temperature Service Structural Bolts, Steel, Heat Treated, 120 /105 ksi Minimum Tensile Strength Seamless and Welded Steel Pipe for Low-Temperature Service Seamless and Welded Carbon and Alloy Steel Tubes for Low-Temperature Service Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service Alloy Steel Forgings for Pressure and High-Temperature Parts Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts vi Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT 323 329 333 345 347 351 357 361 367 371 381 393 403 409 417 425 433 439 449 457 467 473 477 481 485 489 497 503 515 527 539 551 561 575 585 597 SA-352/SA-352M SA-353/SA-353M SA-354 SA-358/SA-358M SA-369/SA-369M SA-370 SA-372/SA-372M SA-376/SA-376M SA-387/SA-387M SA-388/SA-388M SA-395 ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - SA-403/SA-403M SA-409/SA-409M SA-414/SA-414M SA-420/SA-420M SA-423/SA-423M SA-426 SA-435/SA-435M SA-437/SA-437M SA-449 SA-450/SA-450M SA-451 SA-453/SA-453M SA-455/SA-455M SA-476/SA-476M SA-479/SA-479M SA-480/SA-480M SA-484/SA-484M SA-487/SA-487M SA-494/SA-494M SA-508/SA-508M SA-513 SA-515/SA-515M SA-516/SA-516M SA-517/SA-517M Steel Castings, Ferritic and Martensitic, for Pressure Containing Parts, Suitable for Low Temperature Service Pressure Vessel Plates, Alloy Steel, Percent Nickel, Double-Normalized and Tempered Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners Electric-Fusion-Welded Austenitic Chromium-Nickel Alloy Steel Pipe for High-Temperature Service Carbon and Ferritic Alloy Steel Forged and Bored Pipe for HighTemperature Service Test Methods and Definitions for Mechanical Testing of Steel Products Carbon and Alloy Steel Forgings for Thin-Walled Pressure Vessels Seamless Austenitic Steel Pipe for High-Temperature Central-Station Service Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum Ultrasonic Examination of Heavy Steel Forgings Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures Wrought Austenitic Stainless Steel Piping Fittings Welded Large Diameter Austenitic Steel Pipe for Corrosive or HighTemperature Service Steel, Sheet, Carbon, for Pressure Vessels Piping Fittings of Wrought Carbon Steel and Alloy Steel for LowTemperature Service Seamless and Electric-Welded Low-Alloy Steel Tubes Centrifugally Cast Ferritic Alloy Steel Pipe for High-Temperature Service Straight-Beam Ultrasonic Examination of Steel Plates Alloy Steel Turbine-Type Bolting Material Specially Heat Treated for High-Temperature Service Quenched and Tempered Steel Bolts and Studs General Requirements for Carbon, Ferritic Alloy, and Austenitic Alloy Steel Tubes Centrifugally Cast Austenitic Steel Pipe for High-Temperature Service High-Temperature Bolting Materials, With Expansion Coefficients Comparable to Austenitic Steels Pressure Vessel Plates, Carbon Steel, High-Strength Manganese Ductile Iron Castings for Paper Mill Dryer Rolls Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip General Requirements for Stainless Steel Bars, Billets, and Forgings Steel Castings Suitable for Pressure Service Castings, Nickel and Nickel Alloy Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure Vessels Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing Pressure Vessel Plates, Carbon Steel, for Intermediate- and HigherTemperature Service Pressure Vessel Plates, Carbon Steel, for Moderate- and LowerTemperature Service Pressure Vessel Plates, Alloy Steel, High Strength, Quenched and Tempered vii Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT 605 613 619 627 637 643 701 707 717 725 735 747 759 769 773 783 789 795 799 805 813 825 831 841 845 851 863 891 907 915 917 927 953 957 963 GUIDELINE ON ACCEPTABLE ASTM EDITIONS ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - All materials, originating from an ASTM specification, allowed by the various Code Sections and used for construction within the scope of their rules shall be furnished in accordance with the Material Specifications contained within Section II and this guideline except where otherwise provided in Code Cases or in the applicable Section of the Code Materials covered by these Specifications are acceptable for use in items covered by the Code Sections only to the degree indicated in the applicable Section Materials for Code use should preferably be ordered, produced, and documented on this basis; however, material produced under an ASTM Specification listed in Table 07 ED-1 may be used in lieu of the corresponding ASME Specification as listed in this guideline Material produced to an ASME or ASTM Specification with requirements different from the requirements of the corresponding Specification may also be used in accordance with the above, provided the material manufacturer or vessel manufacturer certifies with evidence acceptable to the Authorized Inspector that the corresponding Specification requirements have been met This guideline lists the Specifications, originating from ASTM, and their acceptable dates of issue as well as the Book sections of the ASME Boiler Code in which the specification is approved for use TABLE ED-1 Book Section Specifications I III IV VIII-1 VIII-2 SA-6/SA-6M Identical -General Requirements, Rolled Products SA-20/SA-20M Identical -General Requirements, Plates ⴛ SA-29/SA-29M Identical -General Requirements, Bars Non Nuc Code Case VIII-3 XII Nuc Code Case ⴛ 07 88c through 07 A08 ⴛ 06 88 through 06 A08 ⴛ 05 88 through 05 A08 ⴛ Latest Adopted ASTM Other Acceptable ASTM Editions SA-31 ⴛ 04⑀1 00 through 04⑀1 Identical except that certification is mandatory in 3.1.7, 14, and an editorial change to 3.1.1 of the ordering requirements SA-36/SA-36M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 05 88 through 05 SA-47/SA-47M ⴛ Identical except for the deletion of welded repair references in 11.2 and 11.3 and mandatory certification in 14.1 99(R04) SA-53/SA-53M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ Identical except for the insertion of test practices in 11.1, and editorial corrections to Table X4.1 01 88a through 01 ⴛ 05 87a through 05 SA-106 ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ Identical except for editorial differences in 8.1, 13.4, and 24.1 and deletion of ASTM caveat 1.5 95 88a through 95 SA-105/SA-105M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ SA-134 ⴛ Identical except for additional requirement as shown in the specification ⴛ ⴛ 96(R05) xlvii Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT A08 A08 84 through 99(R04) 85 through 96(R05) A08 TABLE ED-1 (Cont’d) Book Section Non Nuc Code Case I III IV VIII-1 VIII-2 VIII-3 XII Nuc Code Case SA-135 Identical ⴛ ⴛ ⴛ 01 88 through 01 SA-178/SA-178M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 95 89 through 95 SA-179/SA-179M Identical ⴛ ⴛ 90a(R05) A08 SA-181/SA-181M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 06 A08 SA-182/SA-182M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 07 Identical except for the inclusion of Grade F316Ti in 6.3.1 For ASTM editions prior to -07, for Grades F45 and F56, direct or in-process heat treatment is prohibited For Grades F91 and F911, other acceptable ASTM editions are limited to -05 and later Specifications A08 Other Acceptable ASTM Editions 88a through 90a(R05) 87 through 06 87a through 07 ⴛ ⴛ ⴛ ⴛ 91 88 through 91 SA-193/SA-193M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 07 05 through 07 SA-194/SA-194M ⴛ Identical except for the addition of 6.7 ⴛ ⴛ 01a 87 through 01a 82 through 93 ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - SA-192/SA-192M Identical SA-202/SA-202M Identical ⴛ ⴛ 93 SA-203/SA-203M Identical ⴛ ⴛ ⴛ ⴛ ⴛ 97(R03) SA-204/SA-204M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 03 SA-209/SA-209M Identical ⴛ ⴛ ⴛ ⴛ 03(R07) ⴛ ⴛ ⴛ ⴛ ⴛ 95 SA-210/SA-210M ⴛ ⴛ ⴛ Identical except for editorial differences in Table A08 Latest Adopted ASTM SA-213/SA-213M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 07 Identical except for the additional H Grade heat treatment requirements in 6.2 and Grades T23, T24, T91, T911, T92, and T122 are limited to -06a and later 88 through 03 88 through 03(R07) 88 through 95 01a through 07 ⴛ 90a 88 through 90a A08 SA-216/SA-216M ⴛ ⴛ ⴛ ⴛ ⴛ Identical except for addition of 2.3 and editorial differences in 2.1 and 10.1 ⴛ ⴛ ⴛ 07 84b through 07 A08 SA-217/SA-217M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 07 93 through 07 SA-225/SA-225M Identical ⴛ ⴛ ⴛ ⴛ 03 86 through 03 ⴛ 96 SA-214/SA-214M Identical ⴛ 82 through 97(R03) SA-231/SA-231M Identical except that certification requirements in 13.1 are mandatory xlviii Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT TABLE ED-1 (Cont’d) Book Section Non Nuc Code Case 91 SA-234/SA-234M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ Identical except for Grades WP91 and WP911, other acceptable ASTM editions are limited to -05 and later 07 82a through 07 04 88c through 04 Specifications SA-232/SA-232M Identical SA-240/SA-240M Identical I III IV VIII-1 VIII-2 VIII-3 XII Nuc Code Case ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ Latest Adopted ASTM ⴛ Other Acceptable ASTM Editions A08 ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - SA-249/SA-249M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 04a 88b through 04a Identical except for the deletion of S5, which addresses unstraightened tubes, and S9 is mandatory when 100% joint efficiency is required A08 SA-250/SA-250M ⴛ ⴛ ⴛ ⴛ 05 Identical except that Supplementary Requirement S1 is mandatory when 100% weld joint efficiency is required 88a through 05 A08 SA-263 Identical 03 88 through 03 SA-264 Identical 03 88 through 03 SA-265 Identical 03 88 through 03 SA-266/SA-266M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 03a 87 through 03a SA-268/SA-268M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 05a 88b through 05a A08 SA-275/SA-275M - Magnetic Particle Examination of Forgings Identical except battery powered yokes not permitted prior to -06 06 86 through 06 A08 SA-276 Identical ⴛ 97 SA-278/SA-278M ⴛ Identical except for an editorial change to 5.1.1 and a change to 16.1 making certification mandatory ⴛ 01(R06) 85 through 01(R06) A08 SA-283/SA-283M Identical ⴛ ⴛ ⴛ ⴛ ⴛ 03(R07) 88 through 03(R07) SA-285/SA-285M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 03 82(R87) through 03 SA-299/SA-299M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 04 82(R87) through 04 SA-302/SA-302M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 03 82 through 03 04⑀1 00 through 04⑀1 A08 90b through 04 A08 SA-307 ⴛ ⴛ ⴛ ⴛ ⴛ Identical except for the addition of 5.2 providing chemical requirements for Grade C anchor bolts SA-311/SA-311M ⴛ ⴛ 04 Identical except for the deletion of 5.1.11, revision of Table footnote A, and editorial change to 5.1.9, and 11.1 revised to make certification mandatory xlix Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT TABLE ED-1 (Cont’d) Book Section Specifications I III IV VIII-1 VIII-2 VIII-3 XII Nuc Code Case Non Nuc Code Case SA-312/SA-312M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ Identical except for the deletion of 5.2, revision to 6.2 to add “H” Grade heat treatment requirements, and editorial differences in 7.1 and Table and an editorial correction to the Cr and Ni percent chemical composition for UNS S31002 in Table 85 through 99 SA-325 ⴛ ⴛ ⴛ ⴛ Identical except for the deletion of the term “private label distributor” in 16.1 and 16.5 ⴛ 00 86a through 00 SA-333/SA-333M ⴛ ⴛ Identical except for the deletion of 12.3 that conflicts with 15 ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 04a 94 through 04a ⴛ ⴛ 04a 88⑀1 through 04a 06 88a through 06 07 06a through 07 02b 87 through 02b A08 SA-335/SA-335M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ Identical except for the addition of hardness requirements for P23 and P911 in 9.3 and 14.2.1, and the correction of UNS numbers for P9 and P91 A08 SA-336/SA-336M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ SA-350/SA-350M1 Identical except for the deletion of 6.1.2 and 14.1, revision to 14.2.5, and test reports have been made mandatory ⴛ ⴛ ⴛ ⴛ ⴛ 00 86 through 00 SA-352/SA-352M ⴛ ⴛ Identical except for editorial differences in 2.3 and 9.1 ⴛ ⴛ ⴛ 93⑀1 88 through 93⑀1 ⴛ ⴛ ⴛ 04 87 through 04 SA-354 ⴛ ⴛ ⴛ ⴛ ⴛ Identical except for the deletion of the term “private label distributor” in 15.1 and 15.3.5 00a 86 through 00a SA-351/SA-351M Identical A08 88a through 01a 99 SA-334/SA-334M Identical ⴛ 01a ⴛ Other Acceptable ASTM Editions ⴛ SA-320/SA-320M Identical ⴛ Latest Adopted ASTM SA-353/SA-353M Identical ⴛ ⴛ ⴛ ⴛ ⴛ SA-358/SA-358M ⴛ ⴛ ⴛ ⴛ ⴛ 01 88 through 01 Identical except for clarified heat treatment requirements in 6.3.1, the deletion of 6.3.2.2 for HT-O pipe and 6.3.2.3 for HT-SO pipe, an editorial difference in 1.2, and the following additional requirements apply as shown in the specification A08 SA-369/SA-369M Identical SA-370 Identical ⴛ ⴛ ⴛ ⴛ - Mechanical Testing of Steel Products ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 06 88 through 06 ⴛ ⴛ 05 77 through 05 ⴛ ⴛ ⴛ 03 02 through 03 A08 SA-372/SA-372M Identical A08 SA-376/SA-376M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 06 88 through 06 Identical except for the deletion of HT-O option from 6.2 and 14.1 and clarification of heat treatment requirements in 6.2 A08 SA-387/SA-387M ⴛ ⴛ ⴛ ⴛ ⴛ Identical For Grade 91, acceptable ASTM editions are limited to -06 and later ⴛ ⴛ ⴛ 06a l ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT 88 through 06a TABLE ED-1 (Cont’d) Book Section Specifications SA-388/SA-388M Identical I III IV VIII-1 VIII-2 - Ultrasonic Testing of Forgings SA-395/SA-395M Identical ⴛ Non Nuc Code Case VIII-3 XII Nuc Code Case Latest Adopted ASTM ⴛ 07 ⴛ ⴛ ⴛ 99(R04) SA-403/SA-403M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 07 Identical except for the correction of Table Ni minimum for Grade WP S38815, clarified heat treatment requirements in 6.1 and 6.4, the deletion of 304/304L/304N in 14.5, and the deletion of 5.14 and 5.15 For H Grades, other acceptable ASTM editions are limited to -02 and later Other Acceptable ASTM Editions 04 through 07 80 through 99(R04) 86 through 07 A08 A08 A08 88 through 95a⑀1 SA-409/SA-409M ⴛ ⴛ ⴛ ⴛ 95a⑀1 Identical except for clarified heat treatment requirements for H grade stainless steels and S30815 editorial corrections in 5.3.1 and Tables 1, 2, and 3, deletion of 5.3.2.2 and 5.3.2.3 for the non-heat treated pipe provisions, and the inclusion of a grain size requirement in 5.1.1 for H grade stainless steels A requirement for ASME Stamping has been added and editorial requirements apply as shown in the subtitle of the specification SA-414/SA-414M ⴛ ⴛ ⴛ ⴛ ⴛ 01 Identical except for the deletion of Note A under para 1.3 and the addition of para 6.2 on thickness tolerances 88 through 01 SA-420/SA-420M Identical ⴛ ⴛ ⴛ ⴛ 04 SA-423/SA-423M Identical ⴛ ⴛ ⴛ 95(R04) ⴛ 07 90(R07) 82(R87) through 90(R07) 01a 84b through 01a SA-449 ⴛ ⴛ ⴛ ⴛ Identical except for requiring all mating fastener components to be coated by the same zinc-coating process in 5.1.4 and the deletion of private label distributor in 15.1 and 15.4 00 87 through 00 SA-426/SA-426M ⴛ Identical except for a correction to the molybdenum content for Grade CP91 in Table ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - SA-435/SA-435M Identical - Straight Beam Ultrasonic of Plates SA-437/SA-437M Identical SA-450/SA-450M Identical ⴛ - General Requirements for Tubes SA-451 ⴛ Identical except for editorial differences in 15.1 ⴛ 85a through 04 89 through 95(R04) 80 through 07 ⴛ 96 88a through 96 93 80(R85) through 93 SA-453/SA-453M ⴛ ⴛ ⴛ ⴛ ⴛ 99 86 through 99 Identical except for addition of Table 10 on threading and the editorial revision of 5.2.2 on threading Editorial revision of 13 Certification Section to clarify that the bolting Grade, Class, and Type must be included ⴛ 03 82(R87) through 03 SA-476 ⴛ Identical except for editorial changes in 4.1.6 and 13.1 to make certification mandatory 00(R05) 82 through 00(R05) SA-479/SA-479M ⴛ ⴛ ⴛ ⴛ Identical except for editorial changes to Tables and ⴛ 04 SA-455/SA-455M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ li Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT 87b through 04 A08 TABLE ED-1 (Cont’d) Book Section Specifications I III IV VIII-1 VIII-2 VIII-3 XII Nuc Code Case Non Nuc Code Case Latest Adopted ASTM Other Acceptable ASTM Editions SA-480/SA-480M Identical - General Requirements - Flat Products 03c 88 through 03c SA-484/SA-484M Identical - General Requirements Wrought SS Products 98 87 through 98 ⴛ ⴛ ⴛ 93(R07) SA-487/SA-487M Identical SA-494/SA-494M ⴛ ⴛ ⴛ 88 through 93(R07) - See Section II, Part B SA-508/SA-508M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ Identical except for revision prior to -05b For these A 966/A 966M added to 2.1, 3.1, and 7.2.1 revised to allow A 966 in revisions prior to -05⑀1 reference to Notes and in 6.1.2.2 should be and respectively 05b 87 through 05b SA-513 ⴛ 00 Identical except that Supplementary Requirements S6 and either S7 or S8 at the manufacturer’s option are mandatory ⴛ 03 82 through 03 SA-516/SA-516M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ Identical The reference to Footnote B in Table shall apply to the -04, -05, and -05e editions ⴛ 06 86 through 06 A08 SA-517/SA-517M ⴛ ⴛ ⴛ ⴛ Identical except for Grades A, B, E, F, J, P, and deletion of fusion in 1.1 A08 SA-522/SA-522M Identical ⴛ ⴛ ⴛ SA-524 Identical ⴛ ⴛ ⴛ SA-515/SA-515M Identical SA-530/SA-530M Identical A08 A08 ⴛ ⴛ ⴛ ⴛ ⴛ - General Requirements for Pipe ⴛ ⴛ ⴛ ⴛ 06 87a⑀1 through 06 ⴛ 07 87 through 07 ⴛ ⴛ 93 88 through 93 99 88a through 99 SA-533/SA-533M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 93 87 through 93 SA-537/SA-537M Identical ⴛ ⴛ ⴛ ⴛ ⴛ 06 86 through 06 SA-540/SA-540M ⴛ ⴛ Identical except for correction to the title in section ⴛ ⴛ ⴛ 00 84a through 00 SA-541/SA-541M Identical ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ 05 SA-542/SA-542M Identical ⴛ ⴛ ⴛ ⴛ 99 88 through 99 SA-543/SA-543M Identical ⴛ ⴛ ⴛ 93 87 through 93 lii Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT TABLE ED-1 (Cont’d) Book Section Non Nuc Code Case Latest Adopted ASTM 95(R00) I III IV VIII-1 VIII-2 VIII-3 XII Nuc Code Case SA-553/SA-553M Identical ⴛ ⴛ ⴛ ⴛ ⴛ SA-556/SA-556M Identical ⴛ ⴛ SA-557/SA-557M Identical ⴛ ⴛ 90a 88 through 90a SA-562/SA-562M Identical ⴛ ⴛ 06 82(R87) through 06 SA-563 Identical ⴛ ⴛ ⴛ 04 84 through 04 SA-564/SA-564M Identical ⴛ ⴛ ⴛ ⴛ ⴛ 02 87b through 02 02 ⴛ 06 01 through 06 Specifications SA-568/SA-568M Identical - General Requirements for Steel Sheet SA-572/SA-572M Identical Other Acceptable ASTM Editions 87b through 95(R00) 90a(R95)⑀1 88 through 90a(R95)⑀1 SA-574 ⴛ ⴛ ⴛ ⴛ 04⑀1 97a through 04⑀1 Identical except that Table on chemical requirements has been deleted and Supplementary Requirement S1 is now mandatory Paragraphs 6.1 and 6.2 have been revised to refer to Table S1.1 and 6.3 has been deleted SA-577/SA-577M Identical - Ultrasonic Angle Beam of Plates 90(R07) 86 through 90(R07) SA-578/SA-578M Identical - Ultrasonic Straight Beam of Plates 96(R01) 85 through 96(R01) SA-587 ⴛ Identical except for deletion of 1.5 ⴛ ⴛ 93 ⴛ ⴛ ⴛ ⴛ ⴛ 04 91(R07) SA-592/SA-592M Identical SA-609/SA-609M Identical - Ultrasonic Longitudinal Beam - Castings ⴛ 85 through 04 ⴛ 03 SA-638/SA-638M ⴛ Identical except for an editorial correction in 6.2 ⴛ ⴛ ⴛ 00(R04) 87 through 00(R04) SA-645/SA-645M Identical ⴛ ⴛ ⴛ ⴛ 99a 87(R91) through 99a SA-649/SA-649M Identical ⴛ 04 91a through 04 SA-656/SA-656M Identical ⴛ 00a liii Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT A08 A08 83 through 91(R07) A08 88 through 93 ⴛ SA-612/SA-612M Identical A08 87 through 03 A08 TABLE ED-1 (Cont’d) Book Section Latest Adopted ASTM Other Acceptable ASTM Editions 88 through 96(R05) I III IV VIII-1 VIII-2 VIII-3 XII SA-660 Identical ⴛ ⴛ 96(R05) SA-662/SA-662M Identical ⴛ ⴛ ⴛ 03 86 through 03 SA-666 Identical ⴛ 03 90 through 03 SA-667/SA-667M Identical ⴛ 87(R03) ⴛ 94 Specifications A08 Non Nuc Code Case Nuc Code Case ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - SA-671 ⴛ Identical except for additional requirements that apply as shown in Specification SA-672 ⴛ 94 Identical except for the deletion of pipe Grade K The additional requirements apply as shown in the Specification 03⑀1 85 through 94 81 through 94 A08 SA-675/SA-675M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ Identical except that Supplementary S7 is mandatory and Grades 65 [450] and 70 [485] have been added to S7 Certification is mandatory A08 SA-688/SA-688M ⴛ ⴛ ⴛ ⴛ 04 88a through 04 Identical except that in the case of the -96 and -98 ASTM revisions, solution treatment of Grade UNS N08367 is mandatory SA-691 ⴛ Identical except that the additional requirements apply as shown in the Specification ⴛ SA-693 ⴛ Identical except for aligning the elongation requirements for Gr XM-16 and correction of the max hardness for Gr XM-12 and 630 in Table Also a revision to Note B of Table 98(R02) 85a through 98(R02) 02⑀1 88 through 02⑀1 84 through 90b SA-695 Identical for Type B only ⴛ ⴛ ⴛ 90b SA-696 Identical ⴛ 90a(R06) 07 ⴛ ⴛ ⴛ 95(R04) A08 SA-723/SA-723M ⴛ ⴛ ⴛ Identical except that for Class 2a the minimum elongation shall be 13.5% 02 A08 SA-724/SA-724M ⴛ ⴛ Identical except for an editorial correction to Note B in Table ⴛ ⴛ 06 88 through 06 A08 SA-727/SA-727M Identical A08 SA-703/SA-703M Identical SA-705/SA-705M Identical - General Requirements for Castings ⴛ 87b through 07 87a through 95(R04) ⴛ ⴛ ⴛ 02(R07) SA-731/SA-731M ⴛ Identical except for an editorial correction in Table ⴛ 91 88 through 91 SA-736/SA-736M Identical 03 88 through 03 ⴛ 85 through 90a(R06) liv Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT TABLE ED-1 (Cont’d) Book Section Specifications SA-737/SA-737M Identical I III IV VIII-1 VIII-2 VIII-3 XII Nuc Code Case ⴛ ⴛ ⴛ ⴛ Non Nuc Code Case Latest Adopted ASTM 99(R04) ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - SA-738/SA-738M ⴛ ⴛ ⴛ ⴛ ⴛ ⴛ Identical except for a revision to 1.3 to include a maximum thickness for Grades D and E, an editorial revision to Table and editorially correcting the SI temperatures in Appendix XI SA-739 Identical ⴛ ⴛ ⴛ SA-745/SA-745M - Ultrasonic of Stainless Steel Forgings Identical except for deletion of 1.5 03a SA-749/SA-749M Identical ⴛ - General Requirements for Steel Strip ⴛ ⴛ 87a through 03a 90a(R06) 81a through 90a(R06) 94(R03) 99 86 through 99 87(R03) 97(R02) 01(R06) 89a through 01(R06) SA-751 - Chemical Analysis Test Methods for Steel Identical except for editorial corrections to an element designation in Tables and SA-765/SA-765M Identical 87(R91) thru 99(R04) SA-747/SA-747M ⴛ Identical except for the revision of the mandatory ordering requirements of 4.1.6 and the mandatory use of Supplementary Requirement S15 of SA-781/SA-781M SA-748/SA-748M Identical Other Acceptable ASTM Editions ⴛ 01 94 through 01 SA-770/SA-770M Identical - Tension Testing of Steel Plates ⴛ 86 86(R90)e1 SA-781/SA-781M Identical - Common Requirements for Castings 06 87a through 06 A08 SA-788 Identical - General Requirements for Forgings 06 05c through 06 A08 SA-789/SA-789M ⴛ ⴛ Identical except that the sulfur content for S32808 in Table is corrected to 0.010 ⴛ 05b 88a through 05b A08 SA-790/SA-790M ⴛ ⴛ Identical except that the sulfur content for S32808 in Table is corrected to 0.010 ⴛ 05b 88 through 05b A08 03 96 through 03 SA-803/SA-803M Identical ⴛ ⴛ ⴛ SA-813/SA-813M ⴛ ⴛ ⴛ ⴛ 01(R05) 88a through 01(R05) Identical except for the addition of grain size requirements for H grades and S30815, the deletion of heat treat omitted options, and adding a minimum heat treat temperature for S30815 SA-814/SA-814M Identical ⴛ ⴛ ⴛ ⴛ 05 88a through 05 SA-815/SA-815M Identical ⴛ 99 86 through 99 SA-832/SA-832M Identical ⴛ ⴛ ⴛ 06 84(R89) through 06 lv Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT A08 A08 A08 TABLE ED-1 (Cont’d) Book Section Specifications SA-834 Identical I III IV VIII-1 VIII-2 - Common Requirements for Iron Castings Non Nuc Code Case Latest Adopted ASTM Other Acceptable ASTM Editions VIII-3 XII Nuc Code Case 95(R06) 84 through 95(R06) SA-836/SA-836M Identical ⴛ ⴛ ⴛ 02(R07) SA-841/SA-841M Identical 03a 88 through 03a SA-905 Identical ⴛ 93 91 through 93 A08 SA-941 Identical 06a 99b through 06a A08 SA-960/SA-960M Identical 07 99b through 07 A08 SA-961/SA-961M Identical except for the deletion of the time requirement for purchaser rejection of material in para 18.1 07 99 through 07 A08 SA-962/SA-962M Identical 07 99 through 07 A08 SA-965/SA-965M Identical x x x x x x x 06a A08 SA-985/SA-985M Identical - General Requirements, castings 04a 03 through 04a ⴛ ⴛ 98(R07) A08 SA-995 Identical A08 SA-999/SA-999M - General Requirements, Pipes Identical except for the editions prior to 04a, para 6.2.1 on grade substitution of the 04a edition applies 04a 01 through 04a SA-1008/SA-1008M ⴛ ⴛ Identical except for the addition of 8.1.1.1 on mechanical properties for pressure vessel design 01a 00 through 01a SA-1010/SA-1010M Identical except for an editorial correction to a column heading in Table 01⑀1 SA-1011/SA-1011M Identical 06b 01a through 06b 04a 01 through 04a ⴛ 07 01 through 07 98 93a through 98 SA-1016/SA-1016M Identical A08 - General Requirements, Tubes SA-1017/SA-1017M Identical For Grade 122, acceptable editions 07 and later SF-568M Identical - Threaded Metric Fasteners NOTE: (1) SA-350/SA-350M Grade LF2 forgings, made to revisions earlier than the 2001 ASME Boiler and Pressure Vessel Code, or to ASTM Specification A 350/A 350M with year dates from 1987 through 1997 are acceptable for either Class or Class applications, unless Supplementary Requirement S4 was used to test forgings at a higher test temperature lvi ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT GUIDELINE ON ACCEPTABLE NON-ASTM EDITIONS ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - All materials originating from a non-ASTM Specification allowed by the various Code Sections and used for construction within the scope of their rules shall be furnished in accordance with the Material Specifications contained within Section II and this guideline except where otherwise provided in Code Cases or in the applicable Section of the Code Materials covered by these Specifications are acceptable for use in items covered by the Code Sections only to the degree indicated in the applicable Section Materials for Code use should preferably be ordered, produced, and documented on this basis; however, material produced under a non-ASTM Specification listed in Table ED-2 may be used in lieu of the corresponding 07 ASME Specification as listed in this Appendix Material produced to an ASME or a non-ASTM Specification with requirements different from the requirements of the corresponding Specification may also be used in accordance with the above, provided the material manufacturer or vessel manufacturer certifies with evidence acceptable to the Authorized Inspector that the corresponding Specification requirements have been met This guideline lists the nonASTM Specifications, originating not from ASTM and their acceptable dates of issue as well as the Book sections of the ASME Boiler Code in which the specification is approved for use TABLE ED-2 Book Section Non Nuc Code Case Latest Adopted Other Acceptable Editions VIII-2 VIII-3 XII Nuc Code Case SA/AS-1548 ⴛ ⴛ Identical except for marking as shown in the specification 1995 1995 SA/CSA-G40.21 ⴛ Identical except for marking as shown in the specification ⴛ 2004 Only 1992 and 2004 SA/EN 10028-2 ⴛ ⴛ ⴛ Identical except for marking, tension test and quality as shown in the specification 2003 2003 SA/EN 10028-3 ⴛ ⴛ Identical except for marking and mechanical properties of product thickness over 150 mm as shown in the specification 1992 1992 SA/EN 10028-7 ⴛ Identical except for marking as shown in the specification 2000 2000 A08 SA/GB 6654 ⴛ Identical except for marking as shown in the specification 1996 1996 A08 SA/JIS G3118 ⴛ Identical except for marking, mechanical properties and welding repairs as shown in the specification Annex, supplementary quality requirements, does not apply 2000 2000 SA/JIS G4303 ⴛ Identical except for marking, mechanical properties and welding repairs as shown in the specification Annex, supplementary quality requirements, does not apply 1998 1998 Specifications I III IV VIII-1 GENERAL NOTE: The date of publication of the European standards considered in this Guideline is the year of approval of the standard by CEN This date appears in the body of the standard on the page starting with EN; dates appearing on the front page of an XX EN standard (e.g., XX p BS or NF or DIN) correspond only to the date of adoption by each member country lvii Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT A08 A08 INTENTIONALLY LEFT BLANK lviii Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT GUIDELINES ON MULTIPLE MARKING OF MATERIALS one specification, grade, class, or type Examples are SA-53 and SA-106 (some grades and classes); SA-213 TP304L and TP304; SA-213 TP304 and 304H; and SA-106 B and SA-106 C BACKGROUND A common inquiry topic is the permissibility of using material that is identified with two or more specifications (or grades, classes, or types), even if they have different strengths, or even if one of them is not permitted for use in the construction code of application The Committee has addressed variants of these questions in several interpretations: I-89-11, IIA-92-08, VIII-1-89-269, and VIII-189-197 PROHIBITION ON MULTIPLE MARKING Dual or multiple marking is not acceptable if two or more specifications to which the material is marked have mutually exclusive requirements This prohibition includes more than just chemistry and property requirements Examples are SA-515 and SA-516; the former requires melting to coarse grain practice while the latter requires melting to fine grain practice Another example is SA-213 TP304L and TP304H; the carbon content ranges of these grades have no overlap GUIDELINES ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - The construction codes individually define what materials may be used in boilers, vessels, and components constructed in compliance to their rules If a material meets all of the requirements for a specification for which it is marked, including documentation, if any, and if it meets all requirements for use imposed by the construction code, it may be used The construction codes, in general, not address the case of materials marked with more than one specification, grade, class, or type, so these guidelines are offered for clarification GRADE SUBSTITUTION Grade substitution is not permitted Grade substitution occurs when: (1) the material contains an element (other than nitrogen) that is unspecified for one of the grades marked; and (2) the amount of that element present in the material meets the minimum and maximum composition limits for that element in another grade of a specification contained in Section II, Part A or Part B, whether or not it is also so marked For example, a material meets all of the composition limits for SA-240 304, contains 0.06C and 0.02N, but also contains 0.45% Ti This material cannot be marked or provided as meeting SA-240 304 because the Ti content meets the requirements of SA-240 321 [which is, Ti greater than ⴛ (C + N) but less than 0.7.] Another material, with identical composition, except 0.35% Ti, may be marked SA-240 304 because the Ti content does not meet the minimum requirement for 321 The Ti content is just a residual ACCEPTABILITY OF MULTIPLE MARKING Dual or multiple marking is acceptable, as long as the material so marked meets all of the requirements of all the specifications, grades, classes, and types with which it is marked All of the measured and controlled attributes of the multiply-marked grades or specifications must overlap (e.g., chemistry, mechanical properties, dimensions, and tolerances) and the material so marked must exhibit values that fall within the overlaps Further, the controlled but unmeasured attributes of the specifications or grades must overlap (e.g., melting practices, heat treatments, and inspection.) Many specifications or grades have significant overlap of chemistry ranges or properties It is common for material manufacturers to produce materials that satisfy more than MARKING SELECTION If a material is marked with specifications, grades, classes, or types, it may be used with the allowable stresses, lix Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT design stress intensities, or ratings appropriate for any of the markings on the material, as long as the material specification, grade, class, and type is permitted by the code of construction governing the boiler, vessel, or component in which the material is to be used However, once the designer has selected which marking applies (specification, grade, class types, etc.), the designer must use all the design values appropriate for that selection and may not mix and match values from any other specifications, grades, classes, types, etc., with which the material may be marked OTHER MARKINGS Any other markings, such as marking of non-ASME or non-ASTM material specifications, have no relevance, even if those markings are for materials explicitly prohibited by the construction code being used That is, as long as the one marking, and the documentation required by the material and by the construction code, shows that it meets all the requirements for use of that material in that construction code, any additional markings are irrelevant lx Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT ``,,````,,```,```,,``,,`,,`,,`-`-`,,`,,`,`,,` - Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Chevron Corp/5912388100 Not for Resale, 08/27/2008 14:36:44 MDT