BSI Standards Publication BS EN 15518 3 2011 Winter maintenance equipment — Road weather information systems Part 3 Requirements on measured values of stationary equipments BS EN 15518 3 2011 BRITISH[.]
BS EN 15518-3:2011 BSI Standards Publication Winter maintenance equipment — Road weather information systems Part 3: Requirements on measured values of stationary equipments BS EN 15518-3:2011 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 15518-3:2011 The UK participation in its preparation was entrusted to Technical Committee B/513, Construction equipment and plant and site safety A list of organizations represented on this committee can be obtained on request to its secretary This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application © BSI 2011 ISBN 978 580 65403 ICS 07.060; 13.030.40; 35.240.99 Compliance with a British Standard cannot confer immunity from legal obligations This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2011 Amendments issued since publication Date Text affected BS EN 15518-3:2011 EN 15518-3 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM February 2011 ICS 07.060; 13.030.40; 35.240.99 English Version Winter maintenance equipment - Road weather information systems - Part 3: Requirements on measured values of stationary equipments Matériels de viabilité hivernale - Systèmes d'information météorologique routière - Partie 3: Exigences relatives aux valeurs mesurées par des matériels fixes Winterdienstausrüstung - Straßenzustands- und Wetterinformationssysteme - Teil 3: Anforderungen an gemessene Werte der stationären Anlagen This European Standard was approved by CEN on January 2011 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref No EN 15518-3:2011: E BS EN 15518-3:2011 EN 15518-3:2011 (E) Contents Page Foreword 3 Introduction 4 Scope 5 Normative references 5 Terms and definitions 5 Requirements 7 Tables Table — Measurement requirements 8 BS EN 15518-3:2011 EN 15518-3:2011 (E) Foreword This document (EN 15518-3:2011) has been prepared by Technical Committee CEN/TC 337 “Winter maintenance and road service area maintenance equipment”, the secretariat of which is held by AFNOR This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2011, and conflicting national standards shall be withdrawn at the latest by August 2011 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights EN 15518, Winter maintenance equipment — Road weather information systems, comprises of the following parts: Part 1: Global definitions and components Part 2: Road weather — Recommended observation and forecast Part 3: Requirements on measured values of stationary equipments According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom BS EN 15518-3:2011 EN 15518-3:2011 (E) Introduction Road Weather Information Systems (RWIS) are complex structures used for road maintenance decision support, which feature as a rule the following components: meteorological sensors and instruments, transmission technology, computer systems for processing, representation and storing of information, road weather forecasts and alarms, in relation to traffic control and traffic information systems and more Stationary equipment performs the acquisition of road and meteorological information at a fixed location This part of EN 15518 lays down the requirements for the recommended components of a stationary equipment of a RWIS In the description of requirements a distinction is made between the components forming a basis stationary equipment for winter use and the recommended complementary components The aim is to ensure extensive combination and interchangeability within the systems With a set terminology for the components and the meteorological expressions an attempt is made to counteract a diversity of terms and designations for identical phenomena BS EN 15518-3:2011 EN 15518-3:2011 (E) Scope This European Standard specifies the terminology and performance requirements for all components of stationary equipment within a Road Weather Information Systems (RWIS) Normative references The following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies EN 15144:2007, Winter maintenance equipment — Terminology — Terms for winter maintenance Terms and definitions For the purposes of this document, the terms and definitions given in EN 15144:2007 and the following apply NOTE The following definitions have been established specifically for the RWIS domain 3.1 surface 3.1.1 pavement surface temperature effective radiation temperature of a pavement surface 3.1.2 road surface condition qualification of the status of road surface affected by road weather phenomenon 3.1.3 water film thickness mean thickness of the film of water present on a flat surface 3.2 aerial 3.2.1 relative humidity filling rate of the mass of air with water vapour NOTE It is determined in relation to water, in liquid phase, and recorded under a screen at a height between 1,5 m and 4,0 m from the ground 3.2.2 precipitation exclusion of falling water from the atmosphere in liquid and/or solid form which can be observed and measured on ground 3.2.3 rain precipitation in liquid form BS EN 15518-3:2011 EN 15518-3:2011 (E) 3.2.4 depth of precipitation thickness of the layer of water obtained by precipitation or deposit on a horizontal surface if the precipitations falling in solid form were to melt 3.2.5 depth of snow raw thickness of snow deposited on the ground 3.2.6 intensity of precipitation depth of precipitations collected per unit of time 3.2.7 wind speed (instantaneous and mean wind) ratio of the distance travelled by the air, per unit of time 3.2.8 gust of wind brief, sudden increase in the speed of the wind in relation to its mean value 3.2.9 wind direction (instantaneous and mean wind) direction from where the wind is blowing with respect to the magnetic north 3.2.10 visibility distance defined by the meteorological optical range 3.2.11 total radiation solar radiation received by a horizontal surface from the galactic centre, directed towards the ground, within a spectral range from 0,3 µm to µm 3.2.12 atmospheric radiation high wavelength infrared radiation emitted by the atmosphere, within a spectral range from µm to 100 µm 3.2.13 total cloud cover fraction of the galactic centre hidden by all of the visible clouds NOTE It is defined by the International Meteorological Code 700 It is expressed in octa corresponding to the eighth of the galactic centre occupied by the clouds 3.3 general 3.3.1 screen shelter built in such a manner that it protects its contents against solar radiation, precipitations and condensation and contributes at the same time to ventilation 3.3.2 sampling interval time between two readings meant for the elaboration of a value BS EN 15518-3:2011 EN 15518-3:2011 (E) 3.3.3 measurement interval time between two elaborated values 3.3.4 polling interval time between two transmissions of elaborated values Requirements The requirements hereafter apply to sensors in road conditions However, the accuracy requirements are meant for laboratory testing Sensor set-up, calibration and special handling shall be specified by the manufacturer The first column of Table hereafter states “B” for parameters recommended in a basic configuration, and “O” for parameters considered as optional according to specific applications a) b) Thermal resistance 1) sensors embedded in the pavement need to survive surface temperatures from – 40 °C to + 70 °C; 2) equipment placed in the air need to survive air temperatures from – 40 °C to + 60 °C Chemical resistance All components of the road and weather information system installed on the pavement shall be resistant to the thawing agents and fuels to which roads are normally exposed c) Mechanical resistance Sensors and other components embedded in the pavement shall withstand regular mechanical loads exerted by traffic, including rollovers by snow-clearing machines d) Electro-magnetic resistance All components of the road and weather information system shall not be affected by conventional environing electro-magnetic conditions The equipment defined under this standard shall be considered as “Industrial equipment” BS EN 15518-3:2011 EN 15518-3:2011 (E) Table — Measurement requirements Parameters B Pavement surface temperature Requirements Measuring range: – 30 °C to + 60 °C Resolution: 0,1 °C Accuracy: – 15 °C to 10 °C, (± 0,2 °C) – 30 °C to – 15 °C, (± 0,8 °C) and + 10 °C to 60 °C , (± 0,8 °C) B O Road surface condition Water film thickness Dry: no humidity over the sensor Moist: from (0,01 mm) water film thickness over the sensor Wet: from (0,2 mm) water film thickness over the sensor Streaming water: from (2 mm) water film thickness over the sensor Slippery: detection at least of the presence of partly or wholly solidified aqueous solution over the sensor Measuring range: 0,2 mm to mm Resolution: 0,01 mm Accuracy: 0,2 mm to mm, (± 30 %) Specific averaging can be required by the customer BS EN 15518-3:2011 EN 15518-3:2011 (E) Table (continued) Parameters B Freezing point temperature Requirements Measured: Measuring range: – 30 °C to °C Resolution: 0,1 °C Accuracy: °C to – 15 °C, (± 0,5 °C) – 15 °C to – 30 °C, (± 1,5 °C) This requirement is independent of the de-icing agent being used These accuracies are obtained under the following conditions: - Aqueous solution film thickness: 0,05 mm to 0,5 mm; - Measured from ≤ °C pavement surface temperature Calculated Measuring range : – 30 °C to °C Resolution : 0,1 °C Accuracy : °C to – 2,5 °C, (± 0,5 °C) – 2,5 °C to – 30 °C, (± 20 %) This requirement depends on the de-icing agent being used These accuracies are obtained under the following conditions: O B Road body temperature Air temperature - Aqueous solution film thickness: 0,05 mm to 0,5 mm; - Under defined and constant de-icing agent; - Measured from ≤ °C pavement surface temperature Measuring range: between – 25 °C and + 60 °C Resolution: 0,1 °C Accuracy: ± °C Measuring range: between – 40 °C and + 60 °C Resolution: 0,1 °C Accuracy: ± 0,1°C between – 10°C and + 10°C ± 0,5 °C otherwise B Relative humidity Measuring range: at least between 30 % and 100 % Resolution: 1% Accuracy: ± % between 85 % and 100 % ± % otherwise BS EN 15518-3:2011 EN 15518-3:2011 (E) Table (continued) Parameters B Dew-point temperature Requirements Measured Measuring range: between – 10 °C and + 10 °C Resolution: 0,1 °C Accuracy: ± 0,3 °C Calculated B Precipitation detection time Measuring range: between – 10 °C and + 10 °C and relative humidity > 85 % Resolution: 0,1 °C Accuracy: ± 1,5 °C The following precipitation have to be detected in the following time: min: ≥ 1,2 mm/h min: ≥ 0,4 mm/h 10 min: ≥ 0,1 mm/h B Precipitation type Distinction between solid and liquid precipitation with 80 % confidence within the above precipitation detection time O Precipitation intensity Measuring range: between 0,1 mm/h and 200 mm/h Resolution: 0,1 mm/h Accuracy: ± 30 % of measured value between 0,1 mm/h and 0,5 mm/h ± 20 % of measured value between 0,5 mm/h and mm/h ± 40 % of measured value above mm/h The accuracy is given for liquid precipitation, when measured in a 10 period Solid precipitation shall be expressed in terms of the rainfall equivalent O O Snow depth (measured at the RWIS site) Snow depth (measured on the road surface) Measuring range : cm to 50 cm Resolution : cm Accuracy : ± cm Measuring range : cm to 50 cm Resolution : cm Accuracy : ± cm These requirements shall be adapted to the equipment able to perform this type of measurement This information shall be representative of a given area 10 BS EN 15518-3:2011 EN 15518-3:2011 (E) Table (continued) Parameters O Wind speed Requirements Measuring range: at least between m/s and 35 m/s Resolution: 0,1 m/s Accuracy: ± m/s between m/s and 10 m/s ± 10 % of measured value otherwise Starting value: < m/s The wind speed shall be specified as an average vector over a sliding time interval of 10 O Gust of wind Measuring range : between m/s and 50 m/s Resolution : 0,1 m/s Accuracy : ± m/s between m/s and 10 m/s ± 10 % of measured value otherwise Starting value: < m/s The gust of wind is measured over a period of ≤ s, s being recommended O Wind direction Measuring range : 0° to 359° Resolution: 1° Accuracy: < ± 10° Starting value: < m/s at an initial deflection of 90° The wind direction shall be specified as an average vector over a sliding time interval of 10 O Visibility Measuring range : 10 m to 500 m Resolution : 10 m Accuracy : ± 10 m or ± 20 % of measured value, whichever is greater 11 This page deliberately left blank This page deliberately left blank NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards Institution (BSI) BSI is the national body responsible for preparing British Standards and other standards-related publications, information and services BSI is incorporated by Royal Charter British Standards and other standardization products are published by BSI Standards Limited About us Revisions We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions Our British Standards and other publications are updated by amendment or revision The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process Organizations of all sizes and across all sectors choose standards to help them achieve their goals Information on standards We can provide you with the knowledge that your organization needs to succeed Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop, where hard copies can also be purchased If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team Subscriptions Our range of subscription services are designed to make using standards easier for you For further information on our subscription products go to bsigroup.com/subscriptions With British Standards Online (BSOL) you’ll have instant access to over 55,000 British and adopted European and international standards from your desktop It’s available 24/7 and is refreshed daily so you’ll always be up to date You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member PLUS is an updating service exclusive to BSI Subscribing Members You will automatically receive the latest hard copy of your standards when they’re revised or replaced To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit bsigroup.com/shop With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet Licences can cover as few or as many users as you wish With updates supplied as soon as they’re available, you can be sure your documentation is current For further information, email bsmusales@bsigroup.com BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK We continually improve the quality of our products and services to benefit your business If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI Details and advice can be obtained from the Copyright & Licensing Department Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): orders@bsigroup.com Email (enquiries): cservices@bsigroup.com Subscriptions Tel: +44 845 086 9001 Email: subscriptions@bsigroup.com Knowledge Centre Tel: +44 20 8996 7004 Email: knowledgecentre@bsigroup.com Copyright & Licensing Tel: +44 20 8996 7070 Email: copyright@bsigroup.com