/home/gencode/cen/s12545/125 1 794 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |[.]
BRITISH STANDARD Footwear, leather and imitation leather goods manufacturing machines Ð Noise test code Ð Common requirements ICS 17.140.20; 59.140.40; 61.080 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BS EN 12545:2000 +A1:2009 BS EN 12545:2000+A1:2009 National foreword This British Standard is the UK implementation of EN 12545:2000+A1:2009 It supersedes BS EN 12545:2000 which is withdrawn The start and finish of text introduced or altered by amendment is indicated in the text by tags Tags indicating changes to CEN text carry the number of the CEN amendment For example, text altered by CEN amendment A1 is indicated by !" The UK participation in its preparation was entrusted by Technical Committee MCE/3, Safeguarding of machinery, to Subcommittee MCE/3/12, Leather products machinery — Safety A list of organizations represented on this subcommittee can be obtained on request to its secretary This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application Compliance with a British Standard cannot confer immunity from legal obligations This British Standard, having been prepared under the direction of the Sector Committee for Engineering, was published under the authority of the Standards Committee and comes into effect on 15 July 2000 Amendments/corrigenda issued since publication © BSI 2009 31 December 2009 Implementation of CEN amendment A1:2009 ISBN 978 580 62512 Date Comments EUROPEAN STANDARD EN 12545:2000+A1 NORME EUROPÉENNE EUROPÄISCHE NORM May 2009 ICS 17.140.20; 59.140.40; 61.060 Supersedes EN 12545:2000 English Version Footwear, leather and imitation leather goods manufacturing machines - Noise test code - Common requirements Machines de fabrication de chaussures et d'articles en cuir et en matériaux similaires - Code d'essai acoustique Exigences générales Maschinen zur Herstellung von Leder- und Kunstlederwaren und Schuhwerk - Geräuschmessung Allgemeine Anforderungen This European Standard was approved by CEN on 18 February 2000 and includes Amendment approved by CEN on 17 April 2009 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref No EN 12545:2000+A1:2009: E BS EN 12545:2000+A1:2009 EN 12545:2000+A1:2009 (E) Contents Page Foreword Introduction 4 1 Scope 2 Normative references 3 !Terms and definitions" " 5 4 Description of machinery families .6 5 Sound power level determination 6 6 Emission sound pressure level determination 6 7 Installation and mounting conditions 7 8 Operating conditions .7 9 Measurement uncertainties 10 Information to be recorded 8 11 Information to be reported 8 12 Declaration and verification of noise emission values 8 Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC" " 10 Annex ZB (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC" " 11 Bibliography 12 BS EN 12545:2000+A1:2009 EN 12545:2000+A1:2009 (E) Foreword This document (EN 12545:2000+A1:2009) has been prepared by Technical Committee CEN/TC 201 "Leather and imitation leather goods and footwear manufacturing machinery - Safety", the secretariat of which is held by UNI This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2009, and conflicting national standards shall be withdrawn at the latest by December 2009 This document includes Amendment 1, approved by CEN on 2009-04-17 This document supersedes EN 12545:2000 The start and finish of text introduced or altered by amendment is indicated in the text by tags ! " This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s) !For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document." According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom BS EN 12545:2000+A1:2009 EN 12545:2000+A1:2009 (E) Introduction !This document is a type C standard as stated in EN ISO 12100 The machinery concerned and the extent to which hazards, hazardous situations and hazardous events are covered are indicated in the scope of this document When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard." Scope 1.1 This noise test code specifies common requirements necessary to carry out efficiently and under standardised conditions the determination, declaration and verification of the noise emission characteristics of the following leather and imitation leather goods and footwear manufacturing machinery: !- Cutting and punching machines (EN 12044); - Roughing, scouring, polishing and trimming machines (EN 930); - Footwear moulding machines (EN 1845); - Lasting machines (EN 931); - Nailing machines (EN 12653); - Modular shoe repair equipment (EN 12387); - Shoe and leather presses (EN 12203); Splitting, skiving, cutting, cementing and cement drying machines (EN 13457)." Common requirements given in this standard are complemented by specific requirements on noise given in the above mentioned C-type standards 1.2 Noise emission characteristics include emission sound pressure levels at workstations and the sound power level The determination of these quantities is necessary e.g for: manufacturers to declare the noise emitted; comparing the noise emitted by machines in the family concerned; purposes of noise control at source at the design stage BS EN 12545:2000+A1:2009 EN 12545:2000+A1:2009 (E) 1.3 The use of this noise test code and of the specific requirements on noise given in the relevant C-type standard ensures the reproducibility of the determination of the noise emission characteristics within specified limits determined by the grade of accuracy of the basic noise measurement standards used Preferred noise measurement standards are those of engineering grade of accuracy (grade 2): Normative references !The following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies EN ISO 3743-1, Acoustics – Determination of sound power levels of noise sources – Engineering methods for small movable sources in reverberant fields – Part 1: Comparison method for hard-walled test rooms (ISO 3743-1:1994) EN ISO 3744, Acoustics – Determination of sound power levels of noise sources using sound pressure – Engineering method in an essentially free field over a reflecting plane (ISO 3744:1994) EN ISO 3746, Acoustics – Determination of sound power levels of noise sources using sound pressure – Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:1995) EN ISO 3747, Acoustics – Determination of sound power levels of noise sources using sound pressure – Comparison method for use in situ (ISO 3747:2000)" EN ISO 4871:1996, Acoustics – Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) !EN ISO 9614-1, Acoustics – Determination of sound power levels of noise sources using sound intensity – Part 1: Measurement at discrete points (ISO 9614-1:1993) EN ISO 9614-2, Acoustics – Determination of sound power levels of noise sources using sound intensity – Part 2: Measurement by scanning (ISO 9614-2:1996) EN ISO 11201, Acoustics – Noise emitted by machinery and equipment – Measurement of emission sound pressure levels at a work station and at other specified positions – Engineering method in an essentially free field over a reflecting plane (ISO 11201:1995) EN ISO 11202, Acoustics – Noise emitted by machinery and equipment – Measurement of emission sound pressure levels at a work station and at other specified positions – Survey method in situ (ISO 11202:1995) EN ISO 11204", Acoustics – Noise emitted by machinery and equipment – Measurement of emission sound pressure levels at a work station and at other specified positions – Method requiring environmental corrections (ISO 11204:1995) !Terms and definitions" " !For the purposes of this document the terms and definitions contained in the reference ISO standards apply." The definitions of machine types are contained in the Standards mentioned in the scope Definitions specific to the testing of particular machine sub-families are contained in the relevant noise test code annexes (see clause 4) BS EN 12545:2000+A1:2009 EN 12545:2000+A1:2009 (E) Description of machinery families Leather products machinery as defined in the scope is subdivided into the following families: Cutting and punching machines (!EN 12044"), which include manual swing arms and travelling head cutting presses, powered swing arm cutting presses, beam cutting presses, punching and perforating cutting presses, C – frame presses and automatic presses !Roughing, scouring, polishing and trimming machines (EN 930)" !Footwear moulding machines" " (!EN 1845"), which include direct-on-sole, unit sole and footwear component, full shoe and boot moulding machines !deleted text" !Lasting machines (EN 931), which include tack / staple side lasting machines Nailing machines (EN 12653) which include heel attaching, heel nailing and gang nailing machines Modular shoe repair equipment (EN 12387) which include finishing machines, orthopaedic finishing machines and combined heel and sole presses Shoe and leather presses (EN 12203) which include sole attaching presses, sole and insole moulding machines, back part moulding machines, backer, lining and toe puff attaching presses, ironing presses, marking, stamping labelling and embossing machines, stitch marking machines, upper preforming machines, premoulding machines for thermoplastic counter, counter forming machines, folding presses, activating presses, relasting and last slipping machines, top piece attaching presses, leather button covering machines, automatic presses and integrated shoe and leather pressing manufacturing systems Splitting, skiving cutting, cementing and cement drying machines (EN 13457)" Sound power level determination 5.1 A-weighted time-averaged sound power levels (LWA values) for a particular family of machines shall be determined in accordance with one of the basic noise emission measurement standards listed in clause (!EN ISO 3743-1, EN ISO 3744, EN ISO 3746, EN ISO 3747, EN ISO 9614-1, EN ISO 9614-2, EN ISO 11201, EN ISO 11202 and EN ISO 11204") and the relevant noise test code annex for the machinery family or sub-family This will normally be EN ISO 3744 NOTE Only if none of the grade (engineering) methods is applicable should grade (survey) methods be used 5.2 The standard deviation of reproducibility of measured values is that specified in the basic standard used, unless otherwise stated in the appropriate noise test code annexed to the relevant standard Emission sound pressure level determination 6.1 Quantities to be measured at the workstation(s) specified in the relevant noise test code annexes for each machinery family or sub-family are A-weighted time-averaged emission sound pressure levels LpA and C-weighted peak emission sound pressure levels LpC,peak BS EN 12545:2000+A1:2009 EN 12545:2000+A1:2009 (E) 6.2 The emission sound pressure levels referred to in 6.1 shall be determined using Grade (engineering) methods in accordance with one of the basic noise emission measurement standards listed in clause and in the relevant noise test code annex for the machinery family or sub-family This will normally be EN ISO 11204 NOTE Only if this is not practicable Grade (survey) methods should be used 6.3 The workstations where emission sound pressure levels are to be measured are specified in the noise test code annexed to the Standard appropriate to each particular machine sub-family 6.4 Measurement uncertainty depends on the machine sub-family Unless otherwise stated in the noise test code annexed to the relevant Standard, the standard deviation of reproducibility for A-weighted levels determined using a grade method shall be taken as equal to 1,5 dB Installation and mounting conditions 7.1 The installation and mounting conditions shall be strictly the same for determination of both sound power levels and emission sound pressure levels at workstations, and for declaration purposes 7.2 The machine under test shall be placed on a reflecting (acoustically hard) floor e.g sealed asphalt or concrete 7.3 The installation and mounting arrangements for the measurements shall be the same as those indicated by the manufacturer in the Instruction Handbook (see 7.1) Additional installation and mounting arrangements may be specified in relevant noise test code annexes Any noise reduction features, which are part of the machine under test, shall be in place during the measurement 7.4 Care shall be taken to ensure that any electrical conduits, piping or air ducts which are connected to the machinery not radiate significant amounts of sound energy To achieve this, flexible electric cables and pneumatic hoses shall be used for the machinery under test Operating conditions 8.1 These shall be those specified in the noise test code annexed to the relevant Standard If there is no relevant part, the operating conditions shall be reproducible and representative of the noisiest operation in typical usage of the machine Details of these conditions shall be reported 8.2 The operating conditions shall be strictly the same for the determination of both sound power levels and emission sound pressure levels at workstations and for declaration purposes 8.3 The noise emission values shall be determined for a complete work cycle as defined in the noise test code annexed to the relevant Standard Measurement uncertainties Measurements uncertainties will occur during noise testing The method set down in the noise test code annexed to the relevant Standard is designed to keep them to an acceptable minimum See 5.2 and 6.4 If no value of uncertainty K is specified in the annex to the relevant standard, recommended values of K (see annex A of EN ISO 4871:1996), for the emission sound pressure level and the sound power level, are K = 2,5 dB for engineering methods (grade 2) and K = dB for survey methods (grade 3) BS EN 12545:2000+A1:2009 EN 12545:2000+A1:2009 (E) 10 Information to be recorded Information to be recorded is that required by the basic standards used NOTE The information should be recorded using the model data sheet given in the relevant noise test code annex for the machinery family or sub-family 11 Information to be reported 11.1 The information to be included in the test report shall enable the manufacturer to prepare a noise emission declaration and a third party to verify the declared values The test report shall be included in the manufacturer’s file It is recommended to report the information using the model data sheet given in the relevant noise test code annex for the machinery family or sub-family which includes reference to the basic noise emission standards used, description of mounting and operating conditions used, location of workstation(s) and the noise emission values obtained These are: the A-weighted time averaged emission sound pressure level; the C-weighted peak emission sound pressure level, if necessary; the A-weighted sound power level, if required 11.2 The Data Sheet shall be used to confirm that all requirements of this noise test code have been fulfilled or alternatively identify any deviations and list the justification for those necessary deviations 12 Declaration and verification of noise emission values 12.1 Dual-number noise emission values shall be declared in accordance with the procedures in EN ISO 4871 The declaration shall list values reported under clause 11, presented as required by Annex B.2 of EN ISO 4871:1996 for declared dual-number noise emission values 12.2 The noise declaration shall explicitly state that the noise emission values have been obtained according to this noise test code and the relevant noise test code annex for the machinery family or sub-family If this statement is not true, the noise declaration shall clearly indicate the differences 12.3 The verification shall be performed in accordance with 6.2 of EN ISO 4871:1996 and shall be conducted using the same mounting , installation and operating conditions as those used for the initial determination of those noise emission values as in this noise test code and the noise test code annex in the relevant standard 12.4 The following values shall be declared: 1) A weighted time averaged emission sound pressure level LpA at the workstation, together with uncertainty K (see 9) in decibels; 2) When applicable, C-weighted peak emission sound pressure level LpC peak at the workstation together with uncertainty K (see 9) in decibels; 3) When applicable, A-weighted sound power level LWA together with uncertainty K (see 9) in decibels; The reference of the relevant standards applied shall be given in the declaration BS EN 12545:2000+A1:2009 EN 12545:2000+A1:2009 (E) 12.5 The declared noise emission values of the machine (see Annex B.2 of EN ISO 4871:1996 !deleted text") and reference to both this noise test code and the noise test code annex in the relevant standard, including operating conditions shall be given in the instruction handbook and technical file or other documentation BS EN 12545:2000+A1:2009 EN 12545:2000+A1:2009 (E) Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive Machinery 98/37/EC, amended by 98/79/EC Once this standard is cited in the Official Journal of the European Communities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the relevant Essential Requirements of that Directive and associated EFTA regulations WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard." 10 BS EN 12545:2000+A1:2009 EN 12545:2000+A1:2009 (E) Annex ZB (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 2006/42/EC on machinery Once this standard is cited in the Official Journal of the European Communities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the relevant Essential Requirements of that Directive and associated EFTA regulations WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard." 11 BS EN 12545:2000+A1:2009 EN 12545:2000+A1:2009 (E) Bibliography [1] !EN 12044, Footwear, leather and imitation leather goods manufacturing machines – Cutting and punching machines – Safety requirements [2] EN 930, Footwear, leather and imitation leather goods manufacturing machines – Roughing scouring, polishing and trimming machines – Safety requirements [3] EN 1845, Footwear manufacturing machines – Footwear moulding machines – Safety requirements [4] EN 931, Footwear manufacturing machines – Lasting machines – Safety requirements [5] EN 12653, Footwear, leather and imitation leather manufacturing machines – Nailing machines – Safety requirements [6] EN 12387, Footwear, leather and imitation leather goods manufacturing machines – Modular shoe repair equipment – Safety requirements [7] EN 12203, Footwear, leather and imitation leather goods manufacturing machines – Shoe and leather presses - Safety requirements [8] EN 13457, Footwear, leather and imitation leather goods manufacturing machines – Splitting, skiving, cutting, cementing and cement drying machines – Safety requirements." 12 This page deliberately set blank BS EN 12545:2000 +A1:2009 BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards It presents the UK view on standards in Europe and at the international level It is incorporated by Royal Charter Revisions British Standards are updated by amendment or revision Users of British Standards should make sure that they possess the latest amendments or editions It is the constant aim of BSI to improve the quality of our products and services We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400 BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: orders@bsigroup.com You may also buy directly using a debit/credit card from the BSI Shop on the Website http://www.bsigroup.com/shop In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service Various BSI electronic information services are also available which give details on all its products and services Contact Information Centre Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: info@bsigroup.com Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards For details of these and other benefits contact Membership Administration Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: membership@bsigroup.com Information regarding online access to British Standards via British Standards Online can be found at http://www.bsigroup.com/BSOL Further information about BSI is available on the BSI website at http:// www.bsigroup.com Copyright BSI Group Headquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 www.bsigroup.com/ standards Copyright subsists in all BSI publications BSI also holds the copyright, in the UK, of the publications of the international standardization bodies Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained Details and advice can be obtained from the Copyright and Licensing Manager Tel: +44 (0)20 8996 7070 Email: copyright@bsigroup.com