BS EN 4165-003:2016 BSI Standards Publication Aerospace series — Connectors, electrical, rectangular, modular — Operating temperature 175 °C continuous Part 003: Modules series and series — Product standard BS EN 4165-003:2016 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 4165-003:2016 It supersedes BS EN 4165-003:2008 which is withdrawn The UK participation in its preparation was entrusted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology A list of organizations represented on this committee can be obtained on request to its secretary This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application © The British Standards Institution 2016 Published by BSI Standards Limited 2016 ISBN 978 580 89125 ICS 49.060 Compliance with a British Standard cannot confer immunity from legal obligations This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2016 Amendments/corrigenda issued since publication Date Text affected BS EN 4165-003:2016 EN 4165-003 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM March 2016 ICS 49.060 Supersedes EN 4165-003:2008 English Version Aerospace series - Connectors, electrical, rectangular, modular - Operating temperature 175 °C continuous - Part 003: Modules series and series - Product standard Série aérospatiale - Connecteurs électriques rectangulaires modulaires - Température d'utilisation 175 °C continu - Partie 003 : Modules série et série - Norme de produit Luft- und Raumfahrt - Elektrischer Rechtecksteckverbinder in modularer Bauweise Betriebstemperatur 175 °C konstant - Teil 003: Modul Serie und Serie - Produktnorm This European Standard was approved by CEN on March 2015 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels © 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref No EN 4165-003:2016 E BS EN 4165-003:2016 EN 4165-003:2016 (E) Contents Page European foreword Scope Normative references Terms and definitions 4 Required characteristics 5 Male and female module coding Main general characteristics 10 Designation 11 Marking 13 Technical specification 13 BS EN 4165-003:2016 EN 4165-003:2016 (E) European foreword This document (EN 4165-003:2016) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN) After enquiries and votes carried out in accordance with the rules of this Association, this European Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2016, and conflicting national standards shall be withdrawn at the latest by September 2016 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights This document supersedes EN 4165-003:2008 According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom BS EN 4165-003:2016 EN 4165-003:2016 (E) Scope This European Standard specifies the characteristics of module in the family of modular connector coupled by central threaded coupling, or rack and panel or push-pull latching mechanism For contacts and fillers plug associated see EN 4165-002 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies EN 3155-002, Aerospace series — Electrical contacts used in elements of connection — Part 002: List and utilization of contacts EN 3155-070, Aerospace series — Electrical contacts used in elements of connection — Part 070: Contacts, electrical, male, type A, crimp, class S — Product standard EN 3155-071, Aerospace series — Electrical contacts used in elements of connection — Part 071: Contacts, electrical, female, type A, crimp, class S — Product standard EN 4165-001, Aerospace series — Connectors, electrical, rectangular, modular — Operating temperature 175 °C continuous — Part 001: Technical specification EN 4165-002, Aerospace series — Connectors, electrical, rectangular, modular — Operating temperature 175 °C continuous — Part 002: Specification of performance and contact arrangements Terms and definitions For the purposes of this document, the terms and definitions given in EN 4165-001 apply BS EN 4165-003:2016 EN 4165-003:2016 (E) Required characteristics 4.1 Male module interface dimensions – Series and series See Figure and Table Dimensions are in millimetres Key a Zone of contact (module grounded) Grommet Polarizing keys, see Figure b c Optional design for sealed version Interfacial seal, see 4.5 Figure — Male module series and BS EN 4165-003:2016 EN 4165-003:2016 (E) Table — Male module series and dimensions Size 22-20-16-12 A C max 16,46 18,70 max 13,35 11,65 Mass without contacts g max 3,0 2,3 4.2 Female module interface dimensions – Series and series See Figure and Table Dimensions are in millimetres Key a Zone of contact (module grounded) Grommet Polarizing keys, see Figure b c Optional design for sealed version Socket contact cavity, see 4.5 Figure — Female series and series module BS EN 4165-003:2016 EN 4165-003:2016 (E) Table — Female module series and series dimensions Size 22-20-16-12 series 22,40 A max 33,20 series 30,96 series 17,16 to 17,40 B series 25,72 to 25,96 4.3 Male and female module size 08 contact – Grommet design For series and series C max 13,35 11,65 Male module Female module Key Module grommet Sealing sleeve Figure — Male and female module size 08 BS EN 4165-003:2016 EN 4165-003:2016 (E) 4.4 Blank module series and series Instead of male or female modules: Normal version: g max.; or Lightweight version: 1,5 g max Figure — Blank module 4.5 Module interface dimensions See EN 4165-001, detail on contact and module interface BS EN 4165-003:2016 EN 4165-003:2016 (E) Male and female module coding See Figure and Figure Standard position N Position A Position B Position C Position D Figure — Male and female module polarization BS EN 4165-003:2016 EN 4165-003:2016 (E) Position E NOTE Modules polarized E and F have no shell corresponding Figure — Male and female module polarization Main general characteristics See EN 4165-002 10 Position F BS EN 4165-003:2016 EN 4165-003:2016 (E) Designation 7.1 Electrical modules EXAMPLE Description block ELECTRICAL MODULES Identity block EN4165 A 04G16 N A Number of the basic standard Module series (see EN 4165-002) Series = A Series = B (not for blank module) Module arrangements and grounding module device (see EN 4165-002) Dash = No grounding G = Grounding L = No grounding, quadrax contact Q = Grounding, quadrax contact A = No grounding, grey grommet for EN 3155-070 / EN 3155-071 contacts Y = Blue grommet, shunted, female contacts Z = Brown grommet, shunted, male contacts Peripherical sealing and resistance to fuel Type = Without peripherical sealing and standard resistance to fuel Type = With peripherical sealing and standard resistance to fuel Type = Without peripherical sealing and reinforced resistance to fuel Type = With peripherical sealing and reinforced resistance to fuel Polarization (see Figure 5) N = Normal, or A, B, C, D, E, F Module and contact delivery (see Table 3) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block NOTE The previously used designation (e.g EN4165-04G16A1NA) is inactive for new design and should not be used as designation anymore 11 BS EN 4165-003:2016 EN 4165-003:2016 (E) Table — Types of contacts and delivery modules Modules type Contact code delivery A B G A Male module Delivered without contact Z b c d e 12 See EN 3155-002 Female module Delivered without contact Female module Delivered with contacts with standard barrels a EN3155-003F2222 EN3155-003F2020 EN3155-003F1616 EN3155-003F1212 EN3155-066F0808A Male module Female module N/A C Male module Delivered with contacts with reduced / enlarged barrel a EN3155-xxxx2018 b EN3155-xxxx1614 c EN3155-xxxx1210 d,e EN3155-065M0810A N/A D Female module Delivered with contacts with reduced / enlarged barrel a EN3155-xxxx2018 b EN3155-xxxx1614 c EN3155-xxxx1210 d,e EN3155-066F0810A N/A Delivered with quadrax contacts a Delivered with quadrax contacts a N/A N/A Male module Female module Male module Female module EN3155-074xx e Delivered with following contacts a EN3155-070xx e N/A Shunted, male module Delivered with following contacts a EN3155-008M2222 e without selective gold plating Only affects arrangements with size 20 contacts Only affects arrangements with size 16 contacts Only affects arrangements with size 12 contacts Under standardization F EN3155-008M2222 EN3155-008M2020 EN3155-008M1616 EN3155-008M1212 EN3155-065M0808A N/A Y a Male module Delivered with contacts with standard barrels a – L-Q M EN3155-075xx e Delivered with following contacts a Delivered with following contacts a Delivered with following contacts a Delivered with following contacts a N/A N/A N/A N/A N/A EN3155-071xx e Shunted, female module EN3155-082xx e EN3155-070xx e EN3155-071xx e BS EN 4165-003:2016 EN 4165-003:2016 (E) 7.2 Blank module Blank module is available for all shells (receptacles and plugs) instead of male and female standard modules, in series and series EXAMPLE Description block Identity block BLANK MODULE EN4165-1NL Number of the basic standard Peripherical sealing unsealed = sealed =2 Polarization N = Normal only Version Blank = Normal version L = Lightweight version Marking Marking shall be applied to the module This marking shall include: The identity block as defined in suitable product standard; The date of manufacture (year–week); The manufacturer’s name or trademark Technical specification See EN 4165-001 13 This page deliberately left blank This page deliberately left blank NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards Institution (BSI) BSI is the national body responsible for preparing British Standards and other standards-related publications, information and services BSI is incorporated by Royal Charter British Standards and other standardization products are published by BSI Standards Limited About us Revisions We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions Our British Standards and other publications are updated by amendment or revision The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process Organizations of all sizes and across all sectors choose standards to help them achieve their goals Information on standards We can provide you with the knowledge that your organization needs to succeed Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop, where hard copies can also be purchased If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team Subscriptions Our range of subscription services are designed to make using standards easier for you For further information on our subscription products go to bsigroup.com/subscriptions With British Standards Online (BSOL) you’ll have instant access to over 55,000 British and adopted European and international standards from your desktop It’s available 24/7 and is refreshed daily so you’ll always be up to date You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member PLUS is an updating service exclusive to BSI Subscribing Members You will automatically receive the latest hard copy of your standards when they’re revised or replaced To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit bsigroup.com/shop With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet Licences can cover as few or as many users as you wish With updates supplied as soon as they’re available, you can be sure your documentation is current For further information, email bsmusales@bsigroup.com BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK We continually improve the quality of our products and services to benefit your business If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI Details and advice can be obtained from the Copyright & Licensing Department Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): orders@bsigroup.com Email (enquiries): cservices@bsigroup.com Subscriptions Tel: +44 845 086 9001 Email: subscriptions@bsigroup.com Knowledge Centre Tel: +44 20 8996 7004 Email: knowledgecentre@bsigroup.com Copyright & Licensing Tel: +44 20 8996 7070 Email: copyright@bsigroup.com