www bzfxw com | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |[.]
BRITISH STANDARD Aluminium and aluminium alloys Ð Drawn wire Part Mechanical properties The European Standard EN 1301-2 : 1997 has the status of a British Standard ICS 77.150.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BS EN 1301-2 : 1997 BS EN 1301-2 : 1997 National foreword This British Standard is the English language version of EN 1301-2 : 1997 Together with Parts and of BS EN 1301, it supersedes BS 1475 : 1972 The UK participation in its preparation was entrusted to Technical Committee NFE/35/5, Wrought aluminium and aluminium alloys, which has the responsibility to: ± aid enquirers to understand the text; ± present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; ± monitor related international and European developments and promulgate them in the UK A list of organizations represented on this committee can be obtained on request to its secretary Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled `International Standards Correspondence Index', or by using the `Find' facility of the BSI Standards Electronic Catalogue Compliance with a British Standard does not of itself confer immunity from legal obligations Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages to 8, an inside back cover and a back cover This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 November 1997 BSI 1997 ISBN 580 28637 Amendments issued since publication Amd No Date Text affected EN 1301-2 EUROPEAN STANDARD NORME EUROPEÂENNE EUROPAÈISCHE NORM July 1997 ICS 77.150.10 Descriptors: Aluminium, aluminium alloys, wires, drawn products, extruded products, designation, mechanical properties English version Aluminium and aluminium alloys Ð Drawn wire Ð Part 2: Mechanical properties Aluminium et alliages d'aluminium Ð Fil eÂtire РPartie : CaracteÂristiques meÂcaniques Aluminium und Aluminiumlegierungen Gezogene DraÈhte Ð Teil : Mechanische Eigenschaften This European Standard was approved by CEN on 1997-07-03 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom CEN European Committee for Standardization Comite EuropeÂen de Normalisation EuropaÈisches Komitee fuÈr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref No 1301-2 : 1997 E Page EN 1301-2 : 1997 Foreword This European Standard has been prepared by Technical Committee CEN/TC 132, Aluminium and aluminium alloys, the Secretariat of which is held by AFNOR This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 1998, and conflicting national standards shall be withdrawn at the latest by January 1998 Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 4, Wires and drawing stock to prepare the following standard: Contents Foreword Scope Normative references Tensile test Annex A (normative) Rules for rounding Page 3 EN 1301-2 Aluminium and aluminium alloys Ð Drawn wire Ð Part : Mechanical properties This standard is a part of a set of three standards The other standards deal with: EN 1301-1 Aluminium and aluminium alloys Ð Drawn wire Ð Part : Technical conditions for inspection and delivery EN 1301-3 Aluminium and aluminium alloys Ð Drawn wire Ð Part : Tolerances on dimensions According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom BSI 1997 Page EN 1301-2 : 1997 Scope Tensile test This Part of EN 1301 specifies the mechanical properties of aluminium and aluminium alloy drawn wire for general engineering applications, including rivet manufacture (except aeronautical rivets) It applies to drawn wires, except for electrical or welding purposes It does not apply to drawing stock The designation of aluminium and aluminium alloys, their chemical composition and the temper designations used in this standard are in accordance with EN 573-3 and EN 515 respectively These aluminium and aluminium alloys correspond to the alloys produced in large quantities in Europe (class A as defined in 573-4) The conditions for the sampling shall be in accordance with EN 1301-1 The testing conditions specified in EN 10002-1 shall apply together with the following additional conditions: ± the full section test pieces shall be used; ± the elongation shall be measured on a reference length of 100 mm Tensile strength shall conform to tables to Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications These normative references are cited at the appropriate places in the text and the publications are listed hereafter For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision For undated references the latest edition of the publication referred to applies NOTE Typical values for proof stress and elongation are given for information only Tensile strength values shall be rounded in accordance with annex A For rivet wire in non heat-treatable alloys delivered in H13 temper, the mechanical properties shall be determined in the temper of delivery For rivet wire in heat-treatable alloys delivered in H13 temper, the mechanical properties shall be determined: ± in the delivered temper H13; ± and also in tempers: a) T42 for EN AW-2017A, EN AW-2117 and EN AW-2024 alloys; b) T62 for EN AW-2014A, EN AW-6061 and EN AW-6082 and EN AW-7075 alloys In these cases the mechanical properties limits are those given for the corresponding T4 and T6 tempers ｗｗｗ．ｂｚｆｘｗ．ｃｏｍ EN 515 EN 573-3 EN 573-4 EN 10002-1 EN 1301-1 BSI 1997 Aluminium and aluminium alloys Ð Wrought products Ð Temper designations Aluminium and aluminium alloys Ð Chemical composition and forms of wrought products Ð Part 3: Chemical composition Aluminium and aluminium alloys Ð Chemical composition and forms of wrought products Ð Part 4: Forms of products Metallic materials Ð Tensile testing Ð Part 1: Method of test (at ambient temperature) Aluminium and aluminium alloys Ð Drawn wire Ð Part 1: Technical conditions for inspection and delivery Page EN 1301-2 : 1997 Table Series 000 (Al) Material designation Temper Diameter Rp0,21) Rm d Elongation1) A100 mm up to and including MPa % mm MPa max typical typical EN AW-1098 [Al 99,98] O H14 H18 20 18 10 Ð 85 115 70 Ð Ð Ð 80 110 25 EN AW-1080A [Al 99,8 (A)] O H14 H18 20 18 10 Ð 90 120 80 Ð Ð Ð 85 115 35 EN AW-1070A [Al 99,7] O H14 H18 20 18 10 Ð 95 125 85 Ð Ð Ð 90 120 35 O H14 H16 H18 20 18 15 10 Ð 100 120 140 95 Ð Ð Ð Ð 95 115 135 35 3 EN AW-1050A [Al 99,5] ｗｗｗ．ｂｚｆｘｗ．ｃｏｍ 1) These typical proof stress and elongation values quoted are for information only and will be influenced by the wire diameter and, particularly for the H1X tempers, the method of drawing Table Series 000 (Al Cu) Material designation Temper Diameter Rp0,21) Rm d Elongation1) A100 mm up to and including MPa MPa % mm max typical typical T3 T8 18 18 310 370 Ð 295 310 H132) T4 T6 18 18 18 210 380 440 300 Ð Ð 190 255 415 18 EN AW-2017A [Al Cu4MgSi(A)] H132) T4 18 18 210 380 300 Ð 190 255 18 EN AW-2117 [Al Cu2,5Mg] H132) T4 18 18 170 260 240 Ð 110 160 20 EN AW-2024 [Al Cu4Mg1] H132) T4 18 18 230 420 300 Ð 200 315 18 EN AW-2011 [Al Cu6BiPb] EN AW-2014A [Al Cu4SiMg(A)] 1) These typical proof stress and elongation values quoted are for information only and will be influenced by the wire diameter and, particularly for the H1X tempers, the method of drawing 2) Mechanical properties shall be also tested in T42 temper (EN AW-2017A, EN AW-2117 and EN AW-2024 alloys) or T62 temper (EN AW-2014A alloy), and those given for T4 or T6 temper as above shall apply BSI 1997 Page EN 1301-2 : 1997 Table Series 000 (Al Mn) Material designation Temper Diameter Rp0,21) Rm d Elongation1) A100 mm up to and including MPa MPa % mm max typical typical EN AW-3003 [Al Mn1Cu] O H14 H18 20 18 10 Ð 135 180 130 180 Ð 60 120 175 35 EN AW-3103 [Al Mn1] O H14 H18 20 18 10 Ð 135 170 130 180 Ð 60 120 165 35 1) These typical proof stress and elongation values quoted are information only and will be influenced by the wire diameter and, particularly for the H1X tempers, the method of drawing Table Series 000 (Al Mg) Material designation Temper Diameter Rp0,21) Rm d Elongation1) A100 mm up to and including ｗｗｗ．ｂｚｆｘｗ．ｃｏｍ MPa EN AW-5051A [Al Mg2(B)] EN AW-5251 [Al Mg2] EN AW-5052 [Al Mg2,5] EN AW-5154A [Al Mg3,5(A)] BSI 1997 MPa % mm max typical typical 20 18 18 10 Ð 170 195 245 195 220 245 Ð 85 155 200 200 15 O H14 H18 20 18 10 Ð 215 265 215 265 Ð 95 220 270 15 O H14 H18 H32 H34 H38 20 18 10 18 15 10 Ð 225 275 190 215 260 225 275 Ð 240 265 Ð 100 225 275 145 195 245 15 11 O H14 H18 H32 H34 H36 H38 20 18 10 18 15 10 10 Ð 280 330 235 265 290 310 275 330 Ð 285 315 340 Ð 125 270 320 170 230 250 280 16 11 O H12 H14 H18 Page EN 1301-2 : 1997 Table Series 000 (Al Mg) (continued) Material designation Temper Diameter Rp0,21) Rm d Elongation1) A100 mm up to an including MPa MPa % mm max typical typical EN AW-5754 [Al Mg3] O H12 H14 H18 H32 H34 H38 20 18 18 10 18 15 10 Ð 230 255 305 220 245 290 250 280 305 Ð 270 295 Ð 110 200 250 300 160 210 260 16 11 EN AW-5019 [Al Mg5] O H12 H14 H18 H32 H34 H38 20 18 18 18 18 15 10 Ð 295 325 370 280 310 360 320 355 385 Ð 340 370 Ð 150 255 315 360 205 265 320 17 11 ｗｗｗ．ｂｚｆｘｗ．ｃｏｍ 1) These typical proof stress and elongation values quoted are information only and will be strongly influenced by the wire diameter and, particularly for the H1X tempers, the method of drawing Table Series 000 (Al Mg Si) Material designation Temper Diameter Rm Rp0,21) MPa MPa % d EN AW-6060 [Al MgSi] EN AW-6061 [Al Mg1SiCu] EN AW-6063 [Al Mg0,7Si] Elongation1) A100 mm mm max typical typical T393) T393) T4 T6 T893) $6