Bsi bs en 00558 2017

BS EN 558:2017 BSI Standards Publication Industrial valves — Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems — PN and Class designated valves BS EN 558:2017 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 558:2017 It supersedes BS EN 26554:1991 and BS EN 558:2008+A1:2011 which are withdrawn The UK participation in its preparation was entrusted to Technical Committee PSE/18/1, Industrial valves, steam traps, actuators and safety devices against excessive pressure - Valves - Basic standards A list of organizations represented on this committee can be obtained on request to its secretary This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application © The British Standards Institution 2017 Published by BSI Standards Limited 2017 ISBN 978 580 90217 ICS 23.040.99; 23.060.01 Compliance with a British Standard cannot confer immunity from legal obligations This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2017 Amendments/corrigenda issued since publication Date Text affected BS EN 558:2017 EN 558 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM February 2017 ICS 23.040.99; 23.060.10 Supersedes EN 26554:1991, EN 558:2008+A1:2011 English Version Industrial valves - Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems - PN and Class designated valves Robinetterie industrielle - Dimensions face-à-face et face-à-axe de la robinetterie métallique utilisée dans les systèmes de canalisations brides - Appareils de robinetterie désignés PN et Class Industriearmaturen - Baulängen von Armaturen aus Metall zum Einbau in Rohrleitungen mit Flanschen Nach PN und Class bezeichnete Armaturen This European Standard was approved by CEN on 25 December 2016 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels © 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref No EN 558:2017 E BS EN EN 558:2017 558:2017 BS EN 558:2017 EN 558:2017(E) (E) Contents Page European foreword Introduction Scope Normative references Terms and definitions 4.1 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.3 Dimensions and tolerances Basic series Face-to-face and centre-to-face dimensions General Class designated valves with ring joint flanges Valves with lining Raised face flanges 10 Tolerances 10 Annex A (informative) Origin of basic series 29 Annex B (informative) Relationship between DN and NPS 32 Bibliography 33 BS EN EN 558:2017 558:2017 BS EN558:2017 558:2017 (E) (E) EN European foreword This document (EN 558:2017) has been prepared by Technical Committee CEN/TC 69 “Industrial valves”, the secretariat of which is held by AFNOR This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2017, and conflicting national standards shall be withdrawn at the latest by August 2017 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CEN shall not be held responsible for identifying any or all such patent rights This document supersedes EN 558:2008+A1:2011 and EN 26554:1991 The main changes to the previous edition are the following: — PN 500 has been deleted from the scope; — Figure has been updated; — 4.2.4 for raised face flanges has been simplified and Figure has been deleted; — DN 1050 has been added in the scope, Table and Table B.1; — Basic series 111 to 124 have been added in Table and in Table A.1; — FTF series 117 to 121, Class 250 and Class 600 have been added in Table 12; — FTF series 111 and 112 have been added in Table 13; — A new Table 16 was added for steam traps According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom BS EN EN 558:2017 558:2017 BS EN 558:2017 EN 558:2017(E) (E) Introduction The basic series given in this document are taken from the original series shown in Annex A Changes made to the original series will not be automatically incorporated into this document The numbers of the existing ISO basic series are maintained as in ISO 5752:1982 BS EN EN 558:2017 558:2017 BS EN558:2017 558:2017 (E) (E) EN Scope This European Standard specifies the “face–to-face” (FTF) and “centre-to-face” (CTF) dimensions for PN and Class designated metal valves used in flanged pipe systems This European Standard covers valves with the following PN, Class and DN values: — PN 2,5; PN 6; PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; PN 160; PN 250; PN 320; PN 400; — Class 125; Class 150; Class 250; Class 300; Class 600; Class 900; Class 500; Class 500; — DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400; DN 450; DN 500; DN 600; DN 700; DN 750; DN 800; DN 900; DN 000; DN 1050; DN 200; DN 400; DN 600; DN 800; DN 000 For valves in other shell materials than metal the same FTF and CTF dimensions may be used For relationship between DN and NPS see Annex B Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies EN 736-1, Valves - Terminology - Part 1: Definition of types of valves Terms and definitions For the purposes of this document, the terms and definitions given in EN 736-1 and the following apply 3.1 face-to-face dimensions (FTF) [straight pattern valves] distance between the two planes perpendicular to the valve axis located at the extremities of the body end ports or as specified in the relevant valve product standard Note to entry: See Figures to Note to entry: In millimetres 3.2 centre-to-face dimensions (CTF) [angle pattern valves] distance, between the plane located at the extremity of either body end port and perpendicular to its axis and the axis of the other body end port Note to entry: See Figures to Note to entry: In millimetres BS EN EN 558:2017 558:2017 BS EN 558:2017 EN 558:2017(E) (E) Key a b face-to-face (FTF) centre-to-face (CTF) Figure — Face to face and centre to face dimensions Type A Type B Key a face-to-face (FTF) Figure — Flanged valves PN and Class designated (flat and raised faces) Type C Type D Type E Type F Type G Type H Key a face-to-face (FTF) Figure — Flanged valves PN designated (spigot and recess) BS EN EN 558:2017 558:2017 BS EN558:2017 558:2017 (E) (E) EN Class 150 and Class 300 Class 600 and above Large or small male face Large or small female face Large or small tongue Large or small groove NOTE Key For elevation e, see appropriate flange standard a for dimensions see Table c centre-to-face (CTF) b e face-to-face (FTF) elevation Figure — Flanged valves Class designated BS EN EN 558:2017 558:2017 BS EN 558:2017 EN 558:2017(E) (E) Dimensions and tolerances 4.1 Basic series The basic series of FTF and CTF dimensions shall be as given in Table 4.2 Face-to-face and centre-to-face dimensions 4.2.1 General The FTF and CTF dimensions shall be in accordance with Figures to and Table For each type of valve, the basic series to be taken into consideration are given in Table to Table 16 NOTE Table gives complete series In Table to Table 16, the columns of series may be incomplete NOTE The origin of the basic series is shown in Annex A (informative) NOTE For certain sizes/types of valves, alternative dimensions are permitted and these are specified in Table to Table 16 as appropriate 4.2.2 Class designated valves with ring joint flanges For Class designated valves with ring joint flanges, the FTF or CTF dimensions given in Table shall be increased by x as defined in Table and Figure a) b) Key a b FTF = Dimension of Table + x CTF = Dimension of Table + 0,5 x Figure — FTF and CTF dimensions for Class designated valves with ring joint flanges BS EN EN 558:2017 558:2017 BS EN 558:2017 EN 558:2017(E) (E) Table — Ball and plug valves FTF series PN / Class PN — PN 10 — PN 16 X PN 63 — PN 100 X PN 25 — PN 40 PN 160 X Class 125 — Class 150 X Class 300 X Class 250 Class 600 X Xa Xa 12 27 X X Xb X X Class 900 X 28 43c 54 X X 55 56 98 X X X X X X X 100 h 107 g 101 X X Xe Class 500 Class 500 Xf X X X X X Xd X X X a Above DN 40, this series does not apply to top entry full bore ball valves Above DN 300, this series does not apply to full bore all and plug valves b Alternative FTF dimensions for ball valves are 502 (DN 200); 568 (DN 250); 648 (DN 300) c This series applies only to PN 10 ball valves d DN 25; DN 32 are for plug valves, regular pattern only — DN 450; DN 500; DN 600 are for plug valves, venturi pattern only e DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100 are for plug valves, regular pattern only f DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100 are for plug valves, regular pattern only — DN 400 are for plug valves, venturi pattern only g Series only for wafer type; alternative dimension is 183 (DN 125) h Series only for wafer type Table — Diaphragm valves PN / Class PN PN 10 — PN 16 X Class 125 — Class 150 X PN 25 — PN 40 22 FTF series X X X X X X X X X X X X X X 7d Xa, b Xa, b 10 X X 14 X X X X 18d Xc Xc 21 X 54 FTF series X 55 e For flanged and wafer types X 56 c For PN 25, PN 40, Class 300 valves in steel, use: 203 (DN 25); 216 (DN 32); 229 (DN 40); 559 (DN 200) d This series applies to copper alloy valves only; not to be used for cast iron or steel valves a For PN 10, PN 16, Class 150 valves in steel, use: 356 (DN 125); 406 (DN 150) b For PN 10, PN 16, Class 150 valves in cast iron, use: 965 (DN 450) Class 500 Class 500 Class 900 Class 600 Class 250 — Class 300 Class 125 — Class 150 PN 400 PN 250 — PN 320 PN 63 — PN 100 — PN 160 PN 25 — PN 40 PN — PN 10 — PN 16 PN / Class Table — Globe valves — Straight and oblique pattern X 69 X 70 X 71 X X 92 23 X X 94e EN 558:2017 (E) BS EN 558:2017 EN 558:2017 (E) 23 BS EN EN 558:2017 558:2017 BS EN 558:2017 EN 558:2017(E) (E) Table 10 — Globe valves and lift check valves — Angle pattern PN / Class PN PN 10 — PN 16 PN 25 — PN 40 PN 63 — PN 100 — PN 160 CTF series X X PN 250 — PN 320 Class 250 —Class 300 Class 600 Class 900 Class 500 Class 500 X 22a 23a Xb X X X PN 400 Class 125 — Class 150 11 X X 32 57 58 82 93 X X X X X X X X X X a This series applies to copper alloy valves only; not to be used for cast iron or steel valves b For valves in cast iron use: 165 (DN 125); 178 (DN 150) 24 59 X X X X 24 X X X X X X X X X X X X 7b Xc, e, f Xc, e, f 10 X X 14 X X X X 18b Xd Xd 21 X 26 X 54 e For PN 16 valves in cast iron, use: 965 (DN 450) f For PN 16 swing check valves in steel, use: 864 (DN 400) c For PN 16, Class 150 lift check valves in steel, use: 356 (DN 125); 406 (DN 150) d For PN 40, Class 300 lift check valves in steel, use: 203 (DN 25); 216 (DN 32); 229 (DN 40); 559 (DN 200) X 48 FTF series a For lift check valves – angle pattern see Table 10 b This series applies to copper alloy valves only; not to be used for cast iron or steel valves Class 500 Class 500 Class 900 Class 600 Class 250 — Class 300 Class 125 — Class 150 PN 250 — PN 320 — PN 400 PN 160 PN 63 — PN 100 PN 25 — PN 40 PN — PN 10 — PN 16 PN / Class Table 11 — Check valves — Flanged typea X 55 X 56 X 69 X 70 X 71 X 91 92 25 X 99 EN 558:2017 (E) BS EN 558:2017 EN 558:2017 (E) 25 BS EN EN 558:2017 558:2017 BS EN 558:2017 EN 558:2017(E) (E) Table 12 — Check valves — Wafer type PN / Class PN — PN 10 — PN 16 PN 25 — PN 40 Class 125 Class 150 Class 250 Class 300 Class 600 a Only for PN 25 26 FTF series 16 49 50 51 X X X X X X X X X X X X X X X X X 52 X X X 95 96 97 X X Xa X X X X X 117 118 X X 119 120 121 X X X X X X X X X X X X X 37 X X 38 X X 39 X X 56 X X 77 c For CTF Class 2500, use half of the dimension of series 77 X X X X X X X X X 92 105 106 111 112 FTF series (straight pattern) a For CTF Class 900, use half of the dimension of series 105 b For CTF Class 1500, use half of the dimension of series 106 Class 500 Class 500 Class 900 Class 600 Class 300 Class 150 PN 400 PN 320 PN 250 PN 160 PN 63 — PN 100 PN 25 — PN 40 PN 10 — PN 16 PN / Class X X X X Table 13 — Globe control valves Xa X X X X X 11 X X 24 X X 32 X X 40 X X 41 X X 42 CTF series (angle pattern) Xc X 59 Xb Xa X X 93 27 EN 558:2017 (E) BS EN 558:2017 EN 558:2017 (E) 27 BS EN EN 558:2017 558:2017 BS EN 558:2017 EN 558:2017(E) (E) Table 14 — Eccentric rotary plug control valves and segmented ball control valves — Wafer type and flanged type FTF series PN / Class PN 10 — PN 16 — PN 25 — PN 40 36 Xa X X PN 63 — PN 100 Class 150 — Class 300 — Class 600 X X a Applies to eccentric rotary plug control valves only Table 15 — Ball control valves FTF series PN / Class PN 10 — PN 16 X PN 63 — PN 100 X PN 25 — PN 40 X X Class 150 Xa X Class 300 38 X X Xa Class 600 12 X X X X X a Use dimension 502 (DN 200); 568 (DN 250); 648 (DN 300) 39 X Table 16 — Steam traps PN / Class PN 10 — PN 16 PN 25 — PN 40 PN 63 — PN 100 PN 160 FTF series X PN > 160 Class 150 Class 300 Class 600 28 113 114 115 116 X X X X X X X X X X X X X X 122 X 123 X 124 X BS EN EN 558:2017 558:2017 BS EN558:2017 558:2017 (E) (E) EN Annex A (informative) Origin of basic series Table A.1 — Origin of basic series Basic series Origin DIN 3202–1 — Series F ASME/ANSI B16.10, Table 1, column and 9 10 11 12 13 14 15 16 18 19 20 21 22 23 24 25 26 27 28 29 DIN 3202–1 — Series F ASME/ANSI B16.10, Table 2, column 11 ASME/ANSI B16.10, Table 4, column BS 2080 Table 1, Series DIN 3202–1 — Series F 32 DIN 3202–1 — Series F 33 ASME/ANSI B16.10, Table 1, column 16 ASME/ANSI B16.10, Table 1, column 17 ASME/ANSI B16.10, Table 1, column 3; BS 2080, Table 1, column 12 BS 2080, Table 1, Series 13 DIN 3202–1 — Series F DIN 3202–1 — Series F BS 2080, Table 1, Series 16 BS 2080, Table 1, Series 18 ASME/ANSI B16.10, Table 2, column ASME/ANSI B16.10, Table 9, columns and ASME/ANSI B16.10, Table 10, columns 16 and 18 BS 2080, Table 1, Series 63 BS 2080, Table 1, Series 63 ASME/ANSI B16.10, Table 4, column 12 In ISO 5752 X X X X X X X X X X X X X X X X X X X X X – BS 2080, Table 1, Series 64 X DIN 3357–2 and following parts – ASME/ANSI B16.10, Table 9, column DIN 3357–2 and following parts NF E 29–377 – – – 29 BS EN EN 558:2017 558:2017 BS EN 558:2017 EN 558:2017(E) (E) Basic series 30 NF E 29–377 33 ASME/ANSI B16.10, Table 4, column 32 36 37 38 39 40 41 42 43 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 69 70 71 77 82 91 92 93 30 Origin ASME/ANSI B16.10, Table 2, column 17 IEC 60534–3–2, Table IEC 60534–3–2, Table IEC 60534–3–2, Table IEC 60534–3–2, Table Half the dimensions of serie 37 Half the dimensions of serie 38 Half the dimensions of serie 39 NF E 29–305–2 NF E 29–305–2 NF E 29–331 DIN 3202–1, Series F 19 DIN 3202–1, Series F DIN 3202–3, Series K NF E 29–377 NF E 29–377 DIN 3202–3, Series K NF E 29–305–2, FR 10 ASME/ANSI B16.10, Table 5, column ASME/ANSI B16.10, Table 6, column ASME/ANSI B16.10, Table 7, column and column ASME/ANSI B16.10, Table 5, column ASME/ANSI B16.10, Table 6, column ASME/ANSI B16.10, Table 7, column ASME/ANSI B16.10, Table 5, columns and ASME/ANSI B16.10, Table 6, columns and ASME/ANSI B16.10, Table 7, columns and ANSI/ISA S75.16–1994 Table ASME/ANSI B16.10, Table 5, column DIN 3202–1, Series F9 DIN 3202–1, Series F3 DIN 3202–1, Series F34 In ISO 5752 – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – BS EN EN 558:2017 558:2017 BS EN558:2017 558:2017 (E) (E) EN Basic series Origin 94 a 96 a 95 97 98 99 100 101 105 106 107 108 109 110 111 to 112 113 to 116 117 to 121 122 to 124 a a a DIN 3202–1, Series F8 a a ANSI/ISA-75.08.06, Table (long) ANSI/ISA-75.08.06, Table (long) a API 609 Table lug and wafer type Class 150 API 609 Table lug and wafer type Class 300 API 609 Table lug and wafer type Class 600 ANS I/ISA-75.08.06, Table (short) EN 26554, Series 1, 3, 5, API 594 Series Table a In ISO 5752 – – – – – – – – – – – – – – – – – NOTE References to ASME/ANSI B16.10 are taken from 1986 revision a According to agreements between and proposals of the CEN/TC 69 Working Bodies involved in the preparation of this European Standard 31 BS EN EN 558:2017 558:2017 BS EN 558:2017 EN 558:2017(E) (E) Annex B (informative) Relationship between DN and NPS Table B.1 — Relationship between DN and NPS DN 10 NPS ⅜ DN NPS DN NPS a 32 15 20 ắ ẵ 150 750 a 30 25 200 800 32 32 250 900 36 1ẳ 300 10 40 1ẵ 350 12 14 This DN is not included in EN ISO 6708 42 16 48 65 400 1000 1050 a 1200 40 50 1400 56 80 2½ 450 18 1500 60 100 500 20 1600 64 125 600 700 800 000 24 72 28 80 BS EN EN 558:2017 558:2017 BS EN558:2017 558:2017 (E) (E) EN Bibliography [1] [2] [3] ISO 5752:1982, Metal valves for use in flanged pipe systems — Face-to-face and centre-to-face dimensions ANSI/ISA S75.15-1994, Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves (ANSI Classes 150, 300, 600, 900, 500 and 500) ANSI/ISA S75.16-1994, Face-to-Face Dimensions for Flanged Globe-Style Control Valves Bodies (ANSI Classes 900, 500 and 500) [4] API 594:2010, Check Valves: Flanged, Lug, Wafer, and Butt-welding [6] ASME/ANSI B16.10-86, Face-to-Face and End-to-End Dimensions of Ferrous Valves [5] [7] API 609:1997, Butterfly Valves: Double Flanged, Lug- and Wafer-Type BS 2080:1989, Specification for face-to-face, centre-to-face, end-to-end and centre-to-end dimensions of valves [8] DIN 3202-3:1979, Face-to-face dimensions of wafer type valves [10] EN 26554, Flanged automatic steam traps - Face-to-face dimensions (ISO 6554) [9] [11] [12] [13] [14] DIN 3357-2:1981, Full bore steel bore valves EN 60534-3-2:2001, Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves (IEC 60534 2:2001) NF E 29-305-2:1988, Robinetterie industrielle — Appareils de robinetterie utilisés dans les tuyauteries brides — Partie 2: Dimensions face face — Séries FR NF E 29-331:1973, Robinetterie industrielle — Robinets-vannes brides, en acier — Pression nominale PN 64 NF E 29-377:1986, Robinetterie industrielle — Clapets de non-retour métalliques obturateur déplacement angulaire insérer entre brides — Spécifications 33 This page deliberately left blank This page deliberately left blank NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards Institution (BSI) BSI is the national body responsible for preparing British Standards and other standards-related publications, information and services BSI is incorporated by Royal Charter British Standards and other standardization products are published by BSI Standards Limited About us Reproducing extracts We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions For permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process Organizations of all sizes and across all sectors choose standards to help them achieve their goals Information on standards We can provide you with the knowledge that your organization needs to succeed Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop, where hard copies can also be purchased If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team Copyright in BSI publications All the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSI’s prior written consent Storing and using standards Standards purchased in soft copy format: • A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only • The standard may be stored on more than device provided that it is accessible by the sole named user only and that only copy is accessed at any one time • A single paper copy may be printed for personal or internal company use only Standards purchased in hard copy format: • A British Standard purchased in hard copy format is for personal or internal company use only • It may not be further reproduced – in any format – to create an additional copy This includes scanning of the document If you need more than copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see ‘Subscriptions’) Subscriptions Our range of subscription services are designed to make using standards easier for you For further information on our subscription products go to bsigroup.com/subscriptions With British Standards Online (BSOL) you’ll have instant access to over 55,000 British and adopted European and international standards from your desktop It’s available 24/7 and is refreshed daily so you’ll always be up to date You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member PLUS is an updating service exclusive to BSI Subscribing Members You will automatically receive the latest hard copy of your standards when they’re revised or replaced To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit bsigroup.com/shop With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet Licences can cover as few or as many users as you wish With updates supplied as soon as they’re available, you can be sure your documentation is current For further information, email subscriptions@bsigroup.com Revisions Our British Standards and other publications are updated by amendment or revision We continually improve the quality of our products and services to benefit your business If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre Useful Contacts Customer Services Tel: +44 345 086 9001 Email (orders): orders@bsigroup.com Email (enquiries): cservices@bsigroup.com Subscriptions Tel: +44 345 086 9001 Email: subscriptions@bsigroup.com Knowledge Centre Tel: +44 20 8996 7004 Email: knowledgecentre@bsigroup.com Copyright & Licensing Tel: +44 20 8996 7070 Email: copyright@bsigroup.com BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK