© ISO 2013 Road construction and maintenance equipment — Slipform pavers — Definitions and commercial specifications AMENDMENT 1 Matériels pour la construction et l’entretien des routes — Machines à c[.]
INTERNATIONAL STANDARD ISO 16039 First edition 2004-04-15 AMENDMENT 2013-01-15 Road construction and maintenance equipment — Slipform pavers — Definitions and commercial specifications `,,,`,,``,`,,,````,````,``````-`-`,,`,,`,`,,` - AMENDMENT Matériels pour la construction et l’entretien des routes — Machines coffrage glissant— Définitions et spécifications commerciales AMENDEMENT Reference number ISO 16039:2004/Amd.1:2013(E) Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs Not for Resale, 11/15/2013 23:18:58 MST © ISO 2013 ISO 16039:2004/Amd.1:2013(E) `,,,`,,``,`,,,````,````,``````-`-`,,`,,`,`,,` - COPYRIGHT PROTECTED DOCUMENT © ISO 2013 All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyright@iso.org Web www.iso.org Published in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2013 – All rights reserved Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs Not for Resale, 11/15/2013 23:18:58 MST ISO 16039:2004/Amd.1:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work of preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part The main task of technical committees is to prepare International Standards Draft International Standards adopted by the technical committees are circulated to the member bodies for voting Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights ISO shall not be held responsible for identifying any or all such patent rights Amendment to ISO 16039:2004 was prepared by Technical Committee ISO/TC 195, Building construction machinery and equipment `,,,`,,``,`,,,````,````,``````-`-`,,`,,`,`,,` - © ISO 2013 – All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs Not for Resale, 11/15/2013 23:18:58 MST iii `,,,`,,``,`,,,````,````,``````-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs Not for Resale, 11/15/2013 23:18:58 MST ISO 16039:2004/Amd.1:2013(E) Road construction and maintenance equipment — Slipform pavers — Definitions and commercial specifications AMENDMENT Cover page, French title Replace the French version of the title of ISO 16039:2004 by Matériels pour la construction et l’entretien des routes — Machines coffrage glissant— Définitions et spécifications commerciales thereby substituting the term “Machines coffrage glissant” for “Machines pour le pavage” Page 4, 4.4.1 Basic equipment In the third list item, replace “width” by “width and depth” Page 5, 6.3.2, Specifications In the ninth list item, replace “crawler plates” by “track pads” Page 7, 6.8, Additional features of a slipform paver In the ninth list item, replace “rubber” by “non-metallic (e.g rubber, polyurethane) or steel” Page 8, 6.9, Additional equipment In the fourth list item, add “or plough” immediately after “auger” Page 10, Figure A.2 In item no 14 in the legend to Figure A.2, delete the abbreviation “HF” so that the key item reads simply “vibrators” `,,,`,,``,`,,,````,````,``````-`-`,,`,,`,`,,` - © ISO 2013 – All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs Not for Resale, 11/15/2013 23:18:58 MST ISO 16039:2004/Amd.1:2013(E) `,,,`,,``,`,,,````,````,``````-`-`,,`,,`,`,,` - ICS 01.040.91; 93.080.10 Price based on page © ISO 2013 – All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs Not for Resale, 11/15/2013 23:18:58 MST