ISO TC 2/SC 10 Reference number ISO 8765 2011(E) © ISO 2011 INTERNATIONAL STANDARD ISO 8765 Third edition 2011 03 15 Hexagon head bolts with metric fine pitch thread — Product grades A and B Vis à têt[.]
INTERNATIONAL STANDARD ISO 8765 Third edition 2011-03-15 `,,```,,,,````-`-`,,`,,`,`,,` - Hexagon head bolts with metric fine pitch thread — Product grades A and B Vis tête hexagonale filetage métrique pas fin partiellement filetées — Grades A et B Reference number ISO 8765:2011(E) Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 Not for Resale ISO 8765:2011(E) PDF disclaimer This PDF file may contain embedded typefaces In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy The ISO Central Secretariat accepts no liability in this area Adobe is a trademark of Adobe Systems Incorporated Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing Every care has been taken to ensure that the file is suitable for use by ISO member bodies In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below COPYRIGHT PROTECTED DOCUMENT © ISO 2011 All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyright@iso.org Web www.iso.org Published in Switzerland `,,```,,,,````-`-`,,`,,`,`,,` - ii Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 – All rights reserved Not for Resale ISO 8765:2011(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work of preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part The main task of technical committees is to prepare International Standards Draft International Standards adopted by the technical committees are circulated to the member bodies for voting Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights ISO shall not be held responsible for identifying any or all such patent rights ISO 8765 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 10, Product standards for fasteners This third edition cancels and replaces the second edition (ISO 8765:1999), of which it constitutes a minor revision `,,```,,,,````-`-`,,`,,`,`,,` - © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS iii Not for Resale ISO 8765:2011(E) Introduction This International Standard belongs to a complete group of product standards developed by ISO on external hexagon drive fasteners It comprises the following: hexagon head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765); b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676); c) hexagon nuts (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042, ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513); d) hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15072); e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 and ISO 21670) iv © ISO 2011 – All rights reserved `,,```,,,,````-`-`,,`,,`,`,,` - a) Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale INTERNATIONAL STANDARD ISO 8765:2011(E) Hexagon head bolts with metric fine pitch thread — Product grades A and B Scope This International Standard specifies the characteristics of hexagon head bolts with metric fine pitch thread with nominal thread diameters, d, from mm to 64 mm, of product grade A for nominal thread diameters, d, from mm to 24 mm and nominal lengths, l, up to and including 10d or 150 mm, whichever is the shorter, and of product grade B for nominal thread diameters, d, over 24 mm or nominal lengths, l, over 10d or 150 mm, whichever is the shorter If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1, ISO 3506-1, ISO 4753 and ISO 4759-1 It is intended that coarse thread bolts according to ISO 4014 be the first choice `,,```,,,,````-`-`,,`,,`,`,,` - Normative references The following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions ISO 261, ISO general-purpose metric screw threads — General plan ISO 724, ISO general-purpose metric screw threads — Basic dimensions ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread ISO 965-1, ISO general-purpose metric screw threads — Tolerances — Part 1: Principles and basic data ISO 3269, Fasteners — Acceptance inspection ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts, screws and studs ISO 4042, Fasteners — Electroplated coatings ISO 4753, Fasteners — Ends of parts with external ISO metric thread ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C ISO 6157-1, Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements ISO 8839, Mechanical properties of fasteners — Bolts, screws, studs and nuts made of non-ferrous metals ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts ISO 10683, Fasteners — Non-electrolytically applied zinc flake coatings © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 8765:2011(E) Dimensions See Figure and Tables and Symbols and descriptions of dimensions are specified in ISO 225 Dimensions in millimetres β = 15° to 30° b Point shall be chamfered in accordance with ISO 4753 c Incomplete thread u u 2P d Reference datum for dw e Maximum underhead fillet f ds applies if values of ls,min are specified `,,```,,,,````-`-`,,`,,`,`,,` - a Figure Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 – All rights reserved Not for Resale © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale s r kwd k lf Product grade Product grade Product grade B Product grade A Product grade e A Product grade 8,00 7,78 nom = max ds dw 9,2 max da B A 12,57 `,,```,,,,````-`-`,,`,,`,`,,` - 12,73 13,00 0,4 3,54 3,61 min 5,54 5,06 max 5,45 max 5,15 5,3 nom 14,20 max nom = max B A B 14,38 A 11,47 B 11,63 A 7,64 B 0,15 Product grade 41 0,60 28 c max 22 b M8 × a c b ref Thread (d × P) 15,57 15,73 16,00 0,4 4,28 4,35 6,11 6,69 6,22 6,58 6,4 17,59 17,77 14,47 14,63 9,64 9,78 10,00 11,2 0,15 0,60 45 32 26 M10 × 17,57 17,73 18,00 0,6 5,05 5,12 7,21 7,79 7,32 7,68 7,5 19,85 20,03 16,47 16,63 11,57 11,73 12,00 13,7 0,15 0,60 49 36 30 M12 × 1,5 23,16 23,67 24,00 0,6 6,8 6,87 9,71 10,29 9,82 10,18 10 26,17 26,75 22 22,49 15,57 15,73 16,00 17,7 0,2 0,8 57 44 38 M16 × 1,5 29,16 29,67 30,00 0,8 8,51 8,6 12,15 12,85 12,285 12,715 12,5 32,95 33,53 27,7 28,19 19,48 19,67 20,00 22,4 0,2 0,8 65 52 46 M20 × 1,5 35 35,38 36,00 0,8 10,26 10,35 14,65 15,35 14,785 15,215 15 39,55 39,98 33,25 33,61 23,48 23,67 24,00 26,4 0,2 0,8 73 60 54 M24 × Table — Preferred threads 45 — 46 12,8 — 18,28 19,12 — — 18,7 50,85 — 42,75 — 29,48 — 30,00 33,4 0,2 0,8 85 72 66 M30 × 53,8 — 55,0 15,46 — 22,08 22,92 — — 22,5 60,79 — 51,11 — 35,38 — 36,00 39,4 0,2 0,8 97 84 — M36 × 63,1 — 65,0 1,2 17,91 — 25,58 26,42 — — 26 71,3 — 59,95 — 41,38 — 42,00 45,6 0,3 1,0 109 96 — M42 × 73,1 — 75,0 1,6 20,71 — 29,58 30,42 — — 30 10 82,6 — 69,45 — 47,38 — 48,00 52,6 0,3 1,0 121 108 — M48 × 82,8 — 85,0 24,15 — 34,5 35,5 — — 35 12 93,56 — 78,66 — 55,26 — 56,00 63 0,3 1,0 137 — — M56 × 92,8 — 95,0 27,65 — 39,5 40,5 — — 40 13 104,86 — 88,16 — 63,26 — 64,00 71 0,3 1,0 153 — — M64 × Dimensions in millimetres ISO 8765:2011(E) Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale — — — — — — — 200 220 240 260 280 300 — 160 180 149,2 150 89,3 90 139,2 79,4 80 140 69,4 70 129,2 64,4 65 130 59,4 60 119,3 54,4 55 120 49,5 50 99,3 44,5 45 109,3 39,5 40 110 34,5 35 100 nom Thread (d × P) A 91,75 — — — — — — — — — max 98,25 101,75 88,25 — — — — — — — — — B — — — — — — — — 150,8 140,8 130,8 297,4 277,4 257,4 237,7 217,7 197,7 178 158 148 138 128 © ISO 2011 – All rights reserved ls lg ls lg M10 × ls lg M12 × 1,5 ls lg M16 × 1,5 ls lg M20 × 1,5 ls lg ls lg M30 × ls and lge M24 × ls lg M36 × ls lg M42 × ls lg M48 × ls lg M56 × ls lg M64 × Dimensions in millimetres 51,75 41,75 36,75 31,75 26,75 21,75 16,75 11,75 58 48 43 38 33 28 23 18 66,5 56,5 46,5 36,5 31,5 26,5 21,5 16,5 11,5 74 64 54 44 39 34 29 24 19 81,25 71,25 61,25 51,25 41,25 31,25 26,25 21,25 16,25 11,25 90 80 70 60 50 40 35 30 25 20 106 96 86 76 72 62 52 42 32 22 17 116 106 96 86 82 72 62 52 42 32 27 108 98 88 78 74 64 54 44 34 135,5 148 115,5 128 95,5 85,5 75,5 65,5 61,5 51,5 41,5 31,5 21,5 152 132 125 105 85 75 65 55 51 41 31 90,5 70,5 60,5 50,5 40,5 36,5 108 88 78 68 58 54 197,5 215 177,5 195 157,5 175 167 137,5 155 147 117,5 135 140 110,5 128 120 100 90 80 70 66 56 46 183 163 143 123 103 96 76 56 46 36 88,5 81,5 61,5 41,5 111 104 84 64 203 168,5 191 183 148,5 171 163 128,5 151 143 108,5 131 123 116 96 76 66 56 For sizes above the solid, bold, stepped line, see ISO 8676 154 134 114 94 74 67 95,5 75,5 55,5 123 103 83 179 135,5 163 159 115,5 143 139 119 99 92 117 97 77 147 127 107 max max max max max max max max max max max max `,,```,,,,````-`-`,,`,,`,`,,` - 302,6 282,6 262,6 242,3 222,3 202,3 182 162 152 142 132 120,7 118,25 121,75 110,7 108,25 111,75 100,7 90,7 80,6 70,6 65,6 60,6 55,6 50,5 45,5 40,5 35,5 max l Product grade M8 ì Table (continued) ISO 8765:2011(E) â ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale — — — — — — — — — 340 360 380 400 420 440 460 480 500 l — — — — — — — — — — max max 496,85 503,15 476,85 483,15 456,85 463,15 436,85 443,15 416,85 423,15 397,15 402,85 377,15 382,85 357,15 362,85 337,15 342,85 317,15 322,85 B lg ls lg M10 × For 125 mm < lnom u 200 mm For lnom > 200 mm kw,min = 0,7 kmin lg,max = lnom − b c d e P is the pitch of the thread, specified in ISO 261 ls,min = lg,max − 5P For lnom u 125 mm b ⎯ for product grade B, below this stepped line ⎯ for product grade A, above the discontinuous, stepped line; a ls lg M12 × 1,5 ls lg M16 × 1,5 ls lg M20 × 1,5 ls lg ls lg M30 × ls and lge M24 × ls lg M36 × ls lg M42 × ls lg M48 × ls lg M56 × ls lg M64 × Dimensions in millimetres 243 223 203 308,5 331 288,5 311 268,5 291 248,5 271 263 228,5 251 243 208,5 231 223 188,5 211 334 314 294 274 254 234 214 194 174 335,5 363 259 315,5 343 339 295,5 323 319 275,5 303 299 255,5 283 279 235,5 263 259 215,5 243 239 195,5 223 219 175,5 203 199 155,5 183 317 297 277 257 237 217 197 177 157 137 347 327 307 287 267 247 227 207 187 167 max max max max max max max max max max max max ls M8 × Preferred lengths are defined in terms of ls and lg: — 320 NOTE nom A Product grade `,,```,,,,````-`-`,,`,,`,`,,` - Thread (d × P) Table (continued) ISO 8765:2011(E) Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS 9,78 A Not for Resale s r kwd k lf e Product grade Product grade Product grade B Product grade A Product grade Product grade 10,00 nom = max ds dw 11,2 max da B A 15,57 15,73 16,00 0,4 4,28 4,35 6,11 min 6,69 max max 6,22 6,4 6,58 nom 17,59 max nom = max B A B 17,77 A 14,47 B 9,64 14,63 B A 0,15 Product grade 45 0,60 32 c max 26 b 17,57 17,73 18,00 0,6 5,05 5,12 7,21 7,79 7,32 7,68 7,5 19,85 20,03 16,47 16,63 11,57 11,73 12,00 13,7 0,15 0,60 49 36 30 M10 × 1,25 M12 × 1,25 a c b ref Thread (d × P) 20,16 20,67 21,00 0,6 5,96 6,03 8,51 9,09 8,62 8,98 8,8 22,78 23,36 19,15 19,37 13,54 13,73 14,00 15,7 0,15 0,60 57 40 34 M14 × 1,5 26,16 26,67 27,00 0,6 7,81 7,9 11,15 11,85 11,285 11,715 11,5 29,56 30,14 24,85 25,34 17,57 17,73 18,00 20,2 0,2 0,8 61 48 42 M18 × 1,5 29,16 29,67 30,00 0,8 8,51 8,6 12,15 12,85 12,285 12,715 12,5 32,95 33,53 27,7 28,19 19,48 19,67 20,00 22,4 0,2 0,8 65 52 46 M20 × 33 33,38 34,00 0,8 9,56 9,65 13,65 14,35 13,785 14,215 14 37,29 37,72 31,35 31,71 21,48 21,67 22,00 24,4 0,2 0,8 69 56 50 M22 × 1,5 Table — Non-preferred threads 40 — 41 11,66 — 16,65 17,35 — — 17 45,2 — 38 — 26,48 — 27,00 30,4 0,2 0,8 79 66 60 M27 × 49 — 50 14,41 — 20,58 21,42 — — 21 55,37 — 46,55 — 32,38 — 33,00 36,4 0,2 0,8 91 78 — M33 × 58,8 — 60,0 17,21 — 24,58 25,42 — — 25 66,44 — 55,86 — 38,38 — 39,00 42,4 0,3 1,0 103 90 — M39 × 68,1 — 70,0 1,2 19,31 — 27,58 28,42 — — 28 76,95 — 64,7 — 44,38 — 45,00 48,6 0,3 1,0 115 102 — M45 × 78,1 — 80,0 1,6 22,75 — 32,5 33,5 — — 33 10 88,25 — 74,2 — 51,26 — 52,00 56,6 0,3 1,0 129 116 — M52 × 87,8 — 90,0 26,25 — 37,5 38,5 — — 38 12 99,21 — 83,41 — 59,26 — 60,00 67 0,3 1,0 145 — — M60 × Dimensions in millimetres ISO 8765:2011(E) `,,```,,,,````-`-`,,`,,`,`,,` - © ISO 2011 – All rights reserved © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale 44,5 49,5 54,4 59,4 64,4 69,4 79,4 89,3 99,3 109,3 119,3 129,2 139,2 149,2 — — — — — — — — — — 45 50 55 60 65 70 80 90 100 110 120 130 140 150 160 180 200 220 240 260 280 300 320 340 A — — — — — — — — — B — — — — — — — — — max — — — — — — — — — — 150,8 140,8 130,8 302,6 282,6 262,6 242,3 222,3 202,3 182 162 152 142 132 337,15 342,85 317,15 322,85 297,4 277,4 257,4 237,7 217,7 197,7 178 158 148 138 128 120,7 118,25 121,75 110,7 108,25 111,75 100,7 90,7 80,6 70,6 65,6 60,6 55,6 50,5 45,5 max l Product grade `,,```,,,,````-`-`,,`,,`,`,,` - nom Thread (d × P) lg ls lg ls lg ls lg M18 × 1,5 ls lg M20 × ls lg ls lg M27 × ls and lge M22 × 1,5 ls lg M33 × ls lg M39 × ls lg M45 × ls lg M52 × ls lg M60 × Dimensions in millimetres 66,5 56,5 46,5 36,5 31,5 26,5 21,5 16,5 11,5 74 64 54 44 39 34 29 24 19 81,25 71,25 61,25 51,25 41,25 31,25 26,25 21,25 16,25 11,25 90 80 70 60 50 40 35 30 25 20 90 80 76 66 56 46 36 26 21 16 100 90 86 76 66 56 46 36 31 26 112 102 92 82 78 68 58 48 38 28 95,5 85,5 75,5 65,5 61,5 51,5 41,5 31,5 21,5 108 98 88 78 74 64 54 44 34 91,5 81,5 71,5 61,5 57,5 47,5 37,5 27,5 104 94 84 74 70 60 50 40 138,5 151 135,5 148 131,5 144 119,5 132 115,5 128 111,5 124 99,5 89,5 79,5 69,5 65,5 55,5 45,5 35,5 25,5 15,5 166 146 126 119 99 79 69 59 49 45 35 84,5 64,5 54,5 44,5 34,5 102 82 72 62 52 211,5 229 191,5 209 171,5 189 181 151,5 169 161 131,5 149 141 111,5 129 134 104,5 122 114 94 84 74 64 60 50 217 197 177 157 137 117 97 90 70 50 40 82,5 75,5 55,5 105 98 78 237 202,5 225 217 182,5 205 197 162,5 185 177 142,5 165 157 122,5 145 137 102,5 125 117 110 90 70 60 For sizes above the solid, bold, stepped line, see ISO 8676 186 166 146 126 106 86 66 59 87,5 67,5 115 95 211 167,5 195 191 147,5 175 171 127,5 155 151 107,5 135 131 111 91 84 max max max max max max max max max max max max ls M10 × 1,25 M12 × 1,25 M14 × 1,5 Table (continued) ISO 8765:2011(E) Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS — — — — — — — 380 400 420 440 460 480 500 A — — — — — — — — max l B max 496,85 503,15 476,85 483,15 456,85 463,15 436,85 443,15 416,85 423,15 397,15 402,85 377,15 382,85 357,15 362,85 Product grade lg ls lg Not for Resale For 125 mm < lnom u 200 mm For lnom > 200 mm kw,min = 0,7 kmin lg,max = lnom − b c d e P is the pitch of the thread, specified in ISO 261 ls,min = lg,max − 5P For lnom u 125 mm b ⎯ for product grade B, below this stepped line ⎯ for product grade A, above the discontinuous, stepped line; a ls lg ls lg M18 × 1,5 ls lg M20 × ls lg ls lg M27 × ls and lge M22 × 1,5 ls lg M33 × ls lg M39 × ls lg M45 × ls lg M52 × ls lg M60 × Dimensions in millimetres 257 237 302,5 325 282,5 305 262,5 285 277 242,5 265 257 222,5 245 326 306 286 266 246 226 206 327,5 355 351 307,5 335 331 287,5 315 311 267,5 295 291 247,5 275 271 227,5 255 251 207,5 235 231 187,5 215 max max max max max max max max max max max max ls M10 × 1,25 M12 × 1,25 M14 × 1,5 Preferred lengths are defined in terms of ls and lg: — 360 NOTE nom Thread (d × P) Table (continued) ISO 8765:2011(E) `,,```,,,,````-`-`,,`,,`,`,,` - © ISO 2011 – All rights reserved ISO 8765:2011(E) Specifications and reference International Standards See Table Table — Specifications and reference International Standards General requirements Steel Stainless steel International Standard ISO 8992 Tolerance class Thread Mechanical property 6g International Standard Property classa International Standard Product grade Tolerance ISO 724, ISO 965-1 d u 39 mm: 5.6, 8.8, 10.9 d > 39 mm: as agreed d u 24 mm: A2-70, A4-70 24 mm < d u 39 mm: A2-50, A4-50 d > 39 mm: as agreed d u 39 mm: ISO 898-1 d > 39 mm: as agreed d u 39 mm: ISO 3506-1 d > 39 mm: as agreed Materials specified in ISO 8839 For d u 24 mm and l u 10d or 150 mmb: A For d > 24 mm or l > 10d or 150 mmb: B International Standard ISO 4759-1 As processed Requirements for electroplating are specified in ISO 4042 Finish — Coating Non-ferrous metal Requirements for non-electrolytically applied zinc flake coatings are specified in ISO 10683 As processed As processed Requirements for electroplating are specified in ISO 4042 `,,```,,,,````-`-`,,`,,`,`,,` - Material Additional requirements or other finishes or coatings shall be agreed between the supplier and the purchaser Surface integrity Acceptability Limits for surface discontinuities are specified in ISO 6157-1 Acceptance inspection is specified in ISO 3269 a Other property classes are specified in ISO 898-1 for steel and ISO 3506-1 for stainless steel, respectively b Whichever is the shorter Designation EXAMPLE A hexagon head bolt with thread M12 × 1,5, nominal length l = 80 mm and property class 8.8 is designated as follows: Hexagon head screw ISO 8765 - M12 × 1,5 × 80 - 8.8 © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 8765:2011(E) Bibliography ISO 888, Bolts, screws and studs — Nominal lengths, and thread lengths for general purpose bolts [2] ISO 4014, Hexagon head bolts — Product grades A and B [3] ISO 4015, Hexagon head bolts — Product grade B — Reduced shank (shank diameter approximately equal to pitch diameter) [4] ISO 4016, Hexagon head bolts — Product grade C [5] ISO 4017, Hexagon head screws — Product grades A and B [6] ISO 4018, Hexagon head screws — Product grade C [7] ISO 4032, Hexagon nuts, style — Product grades A and B [8] ISO 4033, Hexagon nuts, style — Product grades A and B [9] ISO 4034, Hexagon nuts — Product grade C [10] ISO 4035, Hexagon thin nuts (chamfered) — Product grades A and B [11] ISO 4036, Hexagon thin nuts (unchamfered) — Product grade B [12] ISO 4161, Hexagon nuts with flange — Coarse thread [13] ISO 4162, Hexagon flange bolts — Small series [14] ISO 7040, Prevailing torque type hexagon nuts (with non-metallic insert), style — Property classes 5, and 10 [15] ISO 7041, Prevailing torque type hexagon nuts (with non-metallic insert), style — Property classes and 12 [16] ISO 7042, Prevailing torque type all-metal hexagon nuts, style — Property classes 5, 8, 10 and 12 [17] [18] `,,```,,,,````-`-`,,`,,`,`,,` - [1] ISO 7043, Prevailing torque type hexagon nuts with flange (with non-metallic insert) — Product grades A and B ISO 7044, Prevailing torque type all-metal hexagon nuts with flange — Product grades A and B [19] ISO 7719, Prevailing torque type all-metal hexagon nuts, style — Property classes 5, and 10 [20] ISO 7720, Prevailing torque type all-metal hexagon nuts, style — Property class [21] ISO 8673, Hexagon nuts, style 1, with metric fine pitch thread — Product grade A and B [22] ISO 8674, Hexagon nuts, style 2, with metric fine pitch thread — Product grade A and B [23] ISO 8675, Hexagon thin nuts (chamfered) with metric fine pitch thread — Product grades A and B [24] ISO 8676, Hexagon head screws with metric fine pitch thread — Product grades A and B [25] ISO 10511, Prevailing torque type hexagon thin nuts (with non-metallic insert) 10 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 – All rights reserved Not for Resale ISO 8765:2011(E) [26] ISO 10512, Prevailing torque type hexagon nuts (with non-metallic insert), style 1, with metric fine pitch thread — Property classes 6, and 10 [27] ISO 10513, Prevailing torque type all-metal hexagon nuts, style 2, with metric fine pitch thread — Property classes 8, 10 and 12 [28] ISO 10663, Hexagon nuts with flange — Fine pitch thread [29] ISO 12125, Prevailing torque type hexagon nuts with flange (with non-metallic insert) with metric fine pitch thread — Product grades A and B [30] ISO 12126, Prevailing torque type all-metal hexagon nuts with flange with metric fine pitch thread — Product grades A and B [31] ISO 15071, Hexagon bolts with flange —Small series — Product grade A [32] ISO 15072, Hexagon bolts with flange with metric fine pitch thread — Small series — Product grade A [33] ISO 21670, Hexagon weld nuts with flange `,,```,,,,````-`-`,,`,,`,`,,` - © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS 11 Not for Resale `,,```,,,,````-`-`,,`,,`,`,,` - ISO 8765:2011(E) ICS 21.060.10 Price based on 11 pages © ISO 2011 – Allforrights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale