INTERNATIONAL STANDARD IS0 6020 3 First edition 1994 09 01 Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 3 Compact series with bores from 250 mm to 5[.]
IS0 INTERNATIONAL STANDARD 6020-3 First edition 1994-09-01 Hydraulic fluid power - Mounting dimensions for single rod cylinders, (160 bar) series - Part 3: Compact series with bores from 250 mm to 500 mm Transmissions hydrauliques 16 MPa (160 bar) ri simple Pat-tie 3: S&ie compacte, - Dimensions tige - d ‘in terchangeabilit6 des v&ins a/&sages de 250 mm B 500 mm Reference number 1SO 6020-3: 1994(E) Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - 16 MPa IS0 6020-3:1994(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies) The work of preparing International Standards is normally carried out through IS0 technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization Draft International Standards adopted by the technical committees are circulated to the member bodies for voting Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote International Standard IS0 6020-3 was prepared lSO/TC 131, Fluid power systems, Subcommittee by Technical Committee SC 3, Cylinders IS0 6020 consists of the following parts, under the general title Hydraulic fluid power - Mounting dimensions for single rod cylinders, 76 MPa (760 bar) series: Part 7: Medium series - Part 2: Compact series - Part 3: Compact series with bores from 250 mm to 500 mm Annex A of this part of IS0 6020 is for information only IS0 ‘I994 Atl rights reserved Unless otherwise specified, no part of this publication may be reproduced or utrlized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher International Organrzation for Standardization Case Postale 56 l CH-121 Geneve 20 l Swrtzerland Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - - IS0 IS0 6020-3:1994(E) Introduction In hydraulic fluid power systems, power is transmitted through a liquid under pressure within an enclosed circuit is the fluid power cylinder This is a delinear mechanical force and motion It i.e a piston and piston rod, operating III Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - One component of such systems vice which converts power into consists of a movable element, within a cylindrical bore and controlled INTERNATIONAL STANDARD Q IS0 IS0 Hydraulic fluid power - Mounting dimensions single rod cylinders, 16 MPa (160 bar) series Part 3: Compact IS0 273:1979, and screws Scope NOTES This part of IS0 6020 atlows manufacturers of hydraulic equipment flexibility in the design of metric cylinders and does not restrict technical development but does provide basic guidelines The compact-series square-head cylinders dimensions are most applicable to This part of IS0 6020 only applies to the dimensions of manufactured products It does not apply to their functional characteristics Normative following references standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 6020 At the time of publication, the editions indicated were valid All standards are subject to revision, and parties to agreements based on this part of IS0 6020 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below Members of IEC and IS0 maintain registers of currently valid International `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - Standards 1) for bar = 0.1 MPa = lo5 Pa; MPa Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Fasteners - Clearance holes for bolts IS0 3320:1987, Fluid power systems and components - Cylinder bores and piston rod diameters - Metric series IS0 4395:1978, Fluid ponents - Cylinders and types power systems and comPiston rod thread dimensions IS0 5598:1985, Fluid ponents - Vocabulary power systems and com- IS0 6162:1994, Hydraulic fluid power - Four-screw split-flange connections for use at pressures of 2,5 MPa to 40 MPa (25 bar to 400 bar) - Type I metric series and type I/ inch series The 1994(E) series with bores from 250 mm to 500 mm This part of IS0 6020 establishes metric mounting dimensions for compact-series cylinders with bores from 250 mm to 500 mm, 16 MPa cl60 barll], as required for interchangeability of commonly used hydraulic cylinders 6020-3: Definitions For the purposes of this part of IS0 6020, the definitions given in IS0 5598 and the following definitions apply 3.1 cylinder: Device which converts linear mechanical force and motion 3.2 cylinder body bore: Internal diameter fluid power into of the cylinder 3.3 piston rod: Element which transmits ical force and motion from the piston mechan- = N/mm2 Q IS0 IS0 6020-3: 1994(E) a cylinder is fas- Dimensions The following bore sizes, in millimetres, in this compact series: 250 - 320 - 360 *) - 400 - are included (male) Piston Mounting styles This part of IS0 6020 includes the following styles, in accordance with IS0 6099 MF5 ble 2) MF6 table 3) MPl - MP3 - 2) Head, square Cap, flange square Cap, fixed clevis flange (see figure2 (see (see figure4 Cap, fixed eye (see figure5 Non-preferred size Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS mounting and ta- figure3 and and table4) and table5) trunnion (see (male) (see figure8 trunnion rod characteristics For internally threaded 7.3 For rod end eyes, being prepared trunnion 7.1 This part of IS0 6020 covers piston rods which have a shouldered male thread end (see figure and table for basic dimensions) 7.2 500 integral MT1 Head, figure7 and table7) MT4 Intermediate fixed or movable (male) (see figure and table 9) Bore sizes plain bearing MT2 - Cap, integral and table 8) Mounting dimensions for cylinders manufactured in accordance with this part of IS0 6020 shall be selected from tables to MP5 - Cap, fixed eye with spherical (see figure and table 6) rod ends, see IS0 4395 International Identification statement this part of IS0 6020) Standards (Reference are to Use the following statement in test reports, catalogues and sales literature when electing to comply with this part of IS0 6020: “Interchangeable cylinder mounting dimensions selected in accordance with IS0 6020-3:1994, Hydraulic fluid power - Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 3: Compact series with bores from 250 mm to 500 mm ” `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - 3.4 mounting: Device by which tened to its mating element IS0 6020-3:1994(E) T -.- CT s _-.8 IF - A Table - - General General point dimensions dimensions `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - Figure Reference and part sizes Dimensions 1) Other piston rods that appear 2) See IS0 6162 for flange 3) 360 mm bore k a non-preferred in millimetres in IS0 3320 may be used port dimensions size Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS IS0 IS0 6020-3:1994(E) Dimensions in millimetres Hole in accordance with IS0 273 medium y? P / -_.- - _ -.-.-.- s WF Figure - MF5 Dimensions + - - Head mounting, of head 28 + square mountings, flange square flange Dimensions Bore 250 Rod’) Mh4 140 180 320 180 RD f8 TF 280 380 30 235 325 472 36 350 528 380 490 F max VL UG ZB max max 110 75 445 460 283 110 75 549 520 39 305 110 75 611 575 588 45 340 110 75 683 625 740 56 425 110 75 858 775 220 3602) 180 250 400 220 280 500 280 - FB 360 1) Other piston 2) rods that appear 360 mm bore is a non-preferred Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS in IS0 3320 may be used size R WF in millimetres `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - Table - -.- -? _- - IS0 Q IS0 6020-3:1994(E) Hole in accordance with IS0 273 medium I -_.-. -+-_ -.-_ - _ -.-_ - . -.-_- ZJ + Figure Table Bore 250 - - Rod’) MM 140 MF6 - Dimensions Cap mounting, of cap mountings, square flange square flange Dimensions in millimetres TF FB R ZJ UG max 380 30 235 420 445 472 36 283 475 549 528 39 305 530 611 588 45 340 580 683 740 56 425 710 858 180 320 180 220 3602) 180 250 400 220 280 500 280 360 I) Other piston rods that appear 2) 360 mm bore is a non-preferred in IS0 3320 may be used size `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS IS0 6020-3:1994(E) Q IS0 - I8 . _ - ! -i I CB Figure Table - - MPI - Dimensions Cap mounting, of cap mountings, fixed clevis fixed clevis Dimensions in millimetres Bore 250 Rod’) MA4 140 CB CD MR max L XC UB 90 90 100 125 545 180 110 110 120 152 627 220 125 125 140 175 705 250 140 140 160 195 775 280 180 180 200 250 960 360 180 320 360 2) 180 220 180 250 220 400 500 280 280 360 I) Other piston rods that appear 2) 360 mm bore is a non-preferred in IS0 3320 may be used size `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Q IS0 IS0 6020-3:1994(E) ‘Ic’I!;I :!. .- - _ - _ -_-_-_ A- .4 t-_ REW I L xc+ Figure Table - - MP3 Dimensions - Cap mounting, fixed of cap mountings, eye fixed eye Dimensions in millimetres Rod’, Bore MM EW CD MR max L XC 90 90 100 125 545 110 110 120 152 627 125 125 140 175 705 140 140 160 195 775 180 180 200 250 960 140 250 180 180 320 220 180 360 2) 250 220 400 280 280 500 1) Other piston 2) 360 rods that appear 360 mm bore is a non-oreferred in IS0 3320 may be used size `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS IS0 IS0 6020-3:1994(E) m EP W Figure Table - - MP5 - Dimensions Cap mounting, fixed of cap mountings, eye with fixed spherical eye with plain spherical bearing plain bearing Dimensions lilting Rod’) Bore MM 140 250 in millimetres EP Ex CX MS max LT X0 102 125 125 160 160 580 130 160 160 200 200 675 130 160 160 200 200 730 162 200 200 250 250 830 192 250 250 320 320 030 angle z 180 180 320 220 180 360 2) 250 220 400 280 280 500 360 1) Other 2) 360 mm bore is a non-preferred piston rods that appear Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS in IS0 3320 may be used size `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - 40 Q IS0 IS0 -.-., _ ! ! I TC TL TL Figure Table - - MT1 Dimensions - Head mounting, of head integral mountings, trunnion integral trunnion 6020-3: (male) (male) Dimensions Bore 250 Rod’) MM 140 180 320 180 220 360 2) `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - 400 500 180 250 220 280 280 360 1) Other piston rods that appear 2) 360 mm bore is a non-preferred 1994(E) in millimetres TC UT TD XG TL ZB max 320 520 125 178 100 505 400 650 160 195 125 580 450 740 180 205 145 640 500 820 200 215 160 685 630 030 250 240 200 825 in IS0 3320 may be used size Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS IS0 6020-3: Q IS0 1994(E) I _-_ -_ J - TL (UT) TC n I Figure Table - - MT2 Dimensions - Cap mounting, integral of cap mountings, trunnion integral trunnion (male) (male) Dimensions in millimetres MM 140 250 TC UT TD XJ TL ZB max 320 520 125 393 100 505 400 650 160 450 125 580 450 740 180 500 145 640 500 820 200 525 160 685 630 030 250 615 200 825 180 180 320 220 180 360 2) 250 220 400 280 280 500 360 1) Other piston rods that appear 2) 360 mm bore is a non-preferred 10 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS in IS0 3320 may be used size `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - Rod’) Bore Q IS0 IS0 I I ‘I a II :L L c -.-.- I -.-.-.-_ I - Figure Table xv iUM) I -I - - MT4 - Dimensions with of mountings intermediate with intermediate fixed or movable fixed @ i trunnions or movable fl i-11 // _ ZB+ Mounting 6020-3:1994(E) (male) trunnions (male) Dimensions in millimstres Rod’) Bore 250 MM 140 uw max TM UM TD 480 380 580 600 485 675 xv ZB max TL 125 460 100 735 160 520 125 545 835 180 575 145 750 605 925 200 625 160 945 745 145 250 775 200 180 320 180 220 360 2) 400 180 250 220 variables) 280 `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - 500 280 360 1) Other piston rods that appear 2) 360 mm bore is a non-preferred 3) XV min., XV max and minimum in IS0 3320 may be used size stroke shall be as agreed between the manufacturer and user 11 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS IS0 6020-3:1994(E) Annex A (informative) Bibliography quirements for steel ished bores [ 1] IS0 4393: 1978, Nuid power systems and components - Cylinders - Basic series of piston strokes [3] IS0 4394-l :1980, Nuid components - Cylinder power barrels systems and - Part 7: Re- with specially fin- IS0 6099:1985, Fluid power systems and comcode for ponents - Cylinders - Identification mounting dimensions and mounting types `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - [2] tubes 12 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS IS0 6020-3:1994(E) ICS 23.100.20 Descriptors: hydraulic mounttng dimensions, fluid power, hydraulic interchangeability Pnce based on 12 pages `,,`,,````,,`,,`,`,,``,``,`,-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS equipment, hydraulic cylinders, single rod cylinders, fastening flanges, dimensions,