Microsoft Word C050769e doc Reference number ISO 3386 2 1997/Amd 1 2010(E) © ISO 2010 INTERNATIONAL STANDARD ISO 3386 2 Second edition 1997 06 15 AMENDMENT 1 2010 04 15 Flexible cellular polymeric mat[.]
ISO 3386-2 INTERNATIONAL STANDARD Second edition 1997-06-15 AMENDMENT 2010-04-15 Flexible cellular polymeric materials — Determination of stress-strain characteristics in compression — Part 2: High-density materials AMENDMENT Matériaux polymères alvéolaires souples — Détermination de la caractéristique de contrainte-déformation relative en compression — Partie 2: Matériaux masse volumique élevée AMENDEMENT Reference number ISO 3386-2:1997/Amd.1:2010(E) `,,```,,,,````-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2010 Not for Resale ISO 3386-2:1997/Amd.1:2010(E) PDF disclaimer This PDF file may contain embedded typefaces In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy The ISO Central Secretariat accepts no liability in this area Adobe is a trademark of Adobe Systems Incorporated Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing Every care has been taken to ensure that the file is suitable for use by ISO member bodies In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below COPYRIGHT PROTECTED DOCUMENT © ISO 2010 All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyright@iso.org Web www.iso.org Published in Switzerland `,,```,,,,````-`-`,,`,,`,`,,` - ii Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2010 – All rights reserved Not for Resale ISO 3386-2:1997/Amd.1:2010(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work of preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part The main task of technical committees is to prepare International Standards Draft International Standards adopted by the technical committees are circulated to the member bodies for voting Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights ISO shall not be held responsible for identifying any or all such patent rights Amendment to ISO 3386-2:1997 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses) `,,```,,,,````-`-`,,`,,`,`,,` - iii © ISO 2010 – All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale `,,```,,,,````-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 3386-2:1997/Amd.1:2010(E) Flexible cellular polymeric materials — Determination of stress-strain characteristics in compression — Part 2: High-density materials AMENDMENT `,,```,,,,````-`-`,,`,,`,`,,` - Page 2, Clause Replace the existing text by the following: The following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies ISO 1923, Cellular plastics and rubbers — Determination of linear dimensions ISO 2439, Flexible cellular polymeric materials — Determination of hardness (indentation technique) ISO 7500-1, Metallic materials — Verification of static uniaxial testing machines — Part 1: Tension/compression testing machines — Verification and calibration of the force-measuring system Page 3, Clause Replace the third paragraph of the clause by the following: The test machine shall be capable of measuring the force with an accuracy of ± %, i.e it shall conform to class (or better) of ISO 7500-1 Pages and 4, Subclause 5.5 Replace the existing text by the following: Materials shall not be tested less than 72 h after manufacture unless it can be demonstrated that the mean results obtained at either 16 h or 48 h after manufacture not differ by more than ±10 % from those obtained after 72 h, in which case testing is permitted at 16 h or 48 h, respectively Prior to the test, the test pieces shall be conditioned, undeflected and undistorted, for at least 16 h in one of the following atmospheres: 23 °C ± °C, (50 ± 5) % relative humidity; 27 °C ± °C, (65 ± 5) % relative humidity This conditioning period can form the final part of or, in the case of testing 16 h after manufacture, the whole of the period following manufacture © ISO 2010 – All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 3386-2:1997/Amd.1:2010(E) In the case of quality-control tests, test pieces can be taken a shorter time (down to a minimum of 12 h) after manufacture and testing carried out after conditioning for a shorter period (down to a minimum of h) in one of the atmospheres specified above Testing shall be carried out at the same temperature and relative humidity as those used for conditioning `,,```,,,,````-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2010 – All rights reserved Not for Resale `,,```,,,,````-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 3386-2:1997/Amd.1:2010(E) ICS 83.100 Price based on pages `,,```,,,,````-`-`,,`,,`,`,,` - © ISO 2010 – All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale