Microsoft Word C029094E DOC A Reference number ISO 128 22 1999(E) INTERNATIONAL STANDARD ISO 128 22 First edition 1999 05 01 Technical drawings — General principles of presentation — Part 22 Basic con[.]
INTERNATIONAL STANDARD ISO 128-22 First edition 1999-05-01 Technical drawings — General principles of presentation — Part 22: Basic conventions and applications for leader lines and reference lines Dessins techniques — Principes généraux de représentation — Partie 22: Conventions de base et applications pour les traits de rappel de cote et traits de référence A Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS `,,,,`,,```,``,`,,`,,,`,,,,,,`-`-`,,`,,`,`,,` - Licensee=Aker Solutions/5944276100, User=Tiganik, Aleksander Not for Resale, 05/18/2016 01:48:50 MDT Reference number ISO 128-22:1999(E) ISO 128-22:1999(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work of preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organziations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) in all matters of electrotechnical standardization International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part Draft International Standards adopted by the technical committees are circulated to the member bodies for voting Publication as an International Standard requires approval by at least 75% of the member bodies casting a vote International Standard ISO 128-22 was prepared by Technical Committee ISO/TC 10, Technical drawings, product definition and related documentation, Subcommittee SC 1, Basic conventions ISO 128 consists of the following parts, under the general title Technical drawings — General principles of presentation: Part 20: Basic conventions for lines Part 21: Preparation of lines by CAD systems Part 22: Basic conventions and applications for leader lines and reference lines Part 23: Lines on construction drawings Part 24: Lines on mechanical engineering drawings Part 25: Lines on shipbuilding drawings Part 30: Basic conventions for views Part 31: Additional conventions for views Part 40: Basic conventions for cuts and sections Part 41: Cuts and sections for mechanical engineering drawings Part 50: Basic conventions for representing areas on cuts and sections Part 60: Additional conventions for cuts and sections Annex B forms an integral part of this part of ISO 128 Annex A is for information only `,,,,`,,```,``,`,,`,,,`,,,,,,`-`-`,,`,,`,`,,` - © ISO 1999 All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher International Organization for Standardization Case postale 56 • CH-1211 Genève 20 • Switzerland Internet iso@iso.ch Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=Aker Solutions/5944276100, User=Tiganik, Aleksander Not for Resale, 05/18/2016 01:48:50 MDT INTERNATIONAL STANDARD ISO 128-22:1999(E) © ISO Technical drawings — General principles of presentation — Part 22: Basic conventions and applications for leader lines and reference lines Scope This part of ISO 128 specifies general rules on the presentation of leader and reference lines and their components as well as on the arrangement of instructions on or at leader lines in all kinds of technical documents Normative reference The following normative document contains provisions which, through reference in this text, constitute provisions of this part of ISO 128 For dated references, subsequent amendments to, or revisions of, any of these publications not apply However, parties to agreements based on this part of ISO 128 are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below For undated references, the latest edition of the normative document referred to applies Members of ISO and IEC maintain registers of currently valid International Standards ISO 128-20:1996, Technical drawings — General principles of presentation — Part 20: Basic conventions for lines Terms and definitions For the purposes of this part of ISO 128, the following terms and definitions apply `,,,,`,,```,``,`,,`,,,`,,,,,,`-`-`,,`,,`,`,,` - 3.1 leader line continuous narrow line which establishes the connection between the features of a graphical representation and additional alphanumeric and/or written instructions (notes, technical requirements, item references, etc.) in an unambiguous manner 3.2 reference line continuous narrow line connecting with the leader line horizontally or vertically and on or at which the additional instructions are indicated Presentation of leader lines Leader lines are executed as continuous narrow lines in accordance with ISO 128-20 They are drawn preferably at an angle to the relevant representation and/or the frame limiting the drawing sheet, and not parallel to adjacent lines, e.g hatching lines The inclination to the relevant lines shall be ⬎ 15° See Figures to 13 Leader lines may be drawn with sharp kinks (see Figure 5), and two or more leader lines may be joined up (see Figures 2, 5, 7, and 11) They should not cross other leader lines, reference lines or indications, such as graphical symbols or dimensional values Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=Aker Solutions/5944276100, User=Tiganik, Aleksander Not for Resale, 05/18/2016 01:48:50 MDT ISO 128-22:1999(E) © ISO Leader lines shall terminate at the end which touches the features as follows: with a closed and filled or a closed arrowhead (included angle 15°) if the leader line ends at lines which represent outlines or edges of parts, pipings or cables in plans, charts or diagrams; arrowheads are also drawn at crossing points of these lines with other lines, e.g lines of symmetry (see the examples given in Figures to 7); NOTE If several parallel lines have to be designated, oblique strokes instead of arrowheads are permitted (see IEC 61082-1) See the example given in Figure with a dot (d = ¥ line width) if the leader line ends within the outlines of an object (see the examples given in Figures to 11); without any termination if the leader line ends at another line, e.g dimension line or line of symmetry (see the examples given in Figures 12 and 13) Figure Figure Figure Figure Figure Figure Figure Figure `,,,,`,,```,``,`,,`,,,`,,,,,,`-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=Aker Solutions/5944276100, User=Tiganik, Aleksander Not for Resale, 05/18/2016 01:48:50 MDT © ISO 128-22:1999(E) ISO Figure Figure 10 Figure 11 Figure 12 Figure 13 Presentation of reference lines Reference lines are executed as continuous narrow lines in accordance with ISO 128-20 A reference line may be added to each leader line It is drawn in one of the reading directions of the drawing The reference line shall be drawn either with a fixed length, i.e 20 ¥ line width of the reference line (see the examples given in Figures 15 and 16), or with a length adapted to the length of the indicated instructions (see the examples given in Figures 14, 17, 21 and 22) Figure 14 Figure 15 Figure 16 Figure 17 `,,,,`,,```,``,`,,`,,,`,,,,,,`-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=Aker Solutions/5944276100, User=Tiganik, Aleksander Not for Resale, 05/18/2016 01:48:50 MDT ISO 128-22:1999(E) © ISO In particular cases of application the reference line has to be drawn (see the example given in Figure 15) However, the reference line may be omitted, if the leader line is drawn in one of the reading directions of the drawing and if the indicated instructions are written in the same direction (see the example given in Figure 18), and in all other cases in which this line is not applicable (see the examples given in Figures 12, 19 and 20) Figure 18 Figure 19 Figure 20 Indication of instructions The instructions belonging to the leader lines shall be indicated as follows: preferably above the reference line (see the example given in Figures 14, 17, 21 and 22 and in annex A); centrically behind the leader or reference line (see the example given in Figure 16 and 18); or around, within or behind graphical symbols according to the valid International Standards (see the examples given in Figures 21 and 22 and in annex A) Taking into account the requirements for microcopying in ISO 6428, the instructions should be written at a distance of twice the line width of the reference line above or below the reference line They should not be drawn within the reference line and they should not touch it Figure 21 If individual layers or assembled parts of an object are designated with one leader line, the order of the indications shall correspond with the order of the layers or the parts (see the example given in Figure 22) `,,,,`,,```,``,`,,`,,,`,,,,,,`-`-`,,`,,`, Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Figure 22 Licensee=Aker Solutions/5944276100, User=Tiganik, Aleksander Not for Resale, 05/18/2016 01:48:50 MDT © ISO 128-22:1999(E) ISO Annex A (informative) Graphical supplements contained in other International Standards No Graphical supplement International Standard Application ISO 2553 Indication of further information concerning welds, e.g the number of the welding process ISO 2553 Designation of a field or site weld ISO 2553 Identification of the location of a weld ISO 5459 Datum target frame ISO 6433 Indication of item references (ISO 6433 does not specify only this method) ISO 1101 Frame used for geometrical tolerance requirements ISO 1101 Indication of several toleranced features ISO 129 Indication of dimensions of arc lengths `,,,,`,,```,``,`,,`,,,`,,,,,,`-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=Aker Solutions/5944276100, User=Tiganik, Aleksander Not for Resale, 05/18/2016 01:48:50 MDT ISO 128-22:1999(E) No Graphical supplement © International Standard 9a ISO Application This sign (circle) has the following meanings in the International Standards mentioned below: ISO 1101:—, Table — geometrical (profile) tolerance all around the profile ISO 1101:—, 9.1 — profile tolerance of the entire outline of the cross section ISO 1302:1992, 4.6 — surface texture on all surfaces around a part ISO 1302:1992, clause D.4 — roughness on all surfaces ISO 2553:1992, 7.1 — a peripheral weld all around a part ISO 10135:1994, 6.2 — features, e.g burr, all around a part ISO 10135:1994, 6.4 — machining allowance which applies to all surfaces ISO 13715:1994, 4.2 — the same state of corner all around a part a The sign "circle“ is used for different meanings in the above-mentioned International Standard, e g "all around (profile)“ (ISO 1101) and "all surfaces/corners“ (ISO 1302/ISO 13715) This unfortunate situation should be replaced by an unambiguous solution for all cases of application (see Annex B) It should be taken into account that no sign is needed if any requirement is to be valid for all surfaces/corners of a part In this case the generally valid requirement should be specified by a note (an entry) near the view or cut (section) of the part, within or near the title block or in the space provided for general notes `,,,,`,,```,``,`,,`,,,`,,,,,,`-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=Aker Solutions/5944276100, User=Tiganik, Aleksander Not for Resale, 05/18/2016 01:48:50 MDT © ISO 128-22:1999(E) ISO Annex B (normative) Meaning and application of the graphical supplement "circle" for leader lines The same required characteristic on a number of surfaces or corners of a part connected to each other may be indicated only once if a circle (d = ¥ width of the leader line) is drawn at the connecting point of the leader line and the reference line, see Figures B.1 to B.3 This means that the same requirements apply to all surfaces or corners around the contour or profile of the represented part The "circle" sign shall not be used if either or both of the following occur: a) the indications are ambiguous, b) the indication concerns all surfaces or corners of a part `,,,,`,,```,``,`,,`,,,`,,,,,,`-`-`,,`,,`,`,,` - Figure B.2 Figure B.1 Figure B.3 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=Aker Solutions/5944276100, User=Tiganik, Aleksander Not for Resale, 05/18/2016 01:48:50 MDT ISO 128-22:1999(E) © ISO Bibliography [1] ISO 129:1985, Technical drawings — Dimensioning — General principles, definitions, methods of execution and special indications [2] ISO 1101:—1), Geometrical Product Specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out [3] ISO 1302:1992, Technical drawings — Method of indicating surface texture [4] ISO 2553:1992, Welded, brazed and soldered joints — Symbolic representation on drawings [5] ISO 5459:1981, Technical drawings — Geometrical tolerancing — Datums and datum-systems for geometrical tolerances [6] ISO 6428:1982, Technical drawings — Requirements for microcopying [7] ISO 6433:1981, Technical drawings — Item references [8] ISO 10135:1994, Technical drawings — Simplified representation of moulded, cast and forged parts [9] ISO 13715:1994, Technical drawings — Corners — Vocabulary and indication on drawings [10] IEC 61082-1:1991, Preparation of documents used in electrotechnology — Part 1: General requirements `,,,,`,,```,``,`,,`,,,`,,,,,,`-`-`,,`,,`,`,,` - 1) To be published (Revision of ISO 1101:1983) Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=Aker Solutions/5944276100, User=Tiganik, Aleksander Not for Resale, 05/18/2016 01:48:50 MDT `,,,,`,,```,``,`,,`,,,`,,,,,,`-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=Aker Solutions/5944276100, User=Tiganik, Aleksander Not for Resale, 05/18/2016 01:48:50 MDT ISO 128-22:1999(E) © `,,,,`,,```,``,`,,`,,,`,,,,,,`-`-`,,`,,`,`,,` - ICS 01.100.01 Price based on pages Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Licensee=Aker Solutions/5944276100, User=Tiganik, Aleksander Not for Resale, 05/18/2016 01:48:50 MDT ISO