Document Content ■文件新增 Addition of Document □文件變更 Alteration of Document □文件作廢 Revocation of Document Subject: NQJ & NQX & V1 SMT 治具清洗機作業規範 Doc No.: 901-K0156 REV: NQJ & NQX & V1 SMT Fixture Cleaner Operating Specification PAGE OF Revision History Rev Status Revision Date Revised By 2017/5/26 顧士偉 NEW 陳雅玲 標題新增 V1 廠區 因應越南廠成立所需，增加英文翻譯 For V1 factory build-up requirement, add English translation 2019.3.19 Description 本資料為啟碁科技股份有限公司專有之財產，非經書面許可，不准透露或使用本資料，亦不准複印，複製或轉變成其他形式使用。 The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC Form No.: 2-JQ-021-04, 006 Document Content ■文件新增 Addition of Document □文件變更 Alteration of Document □文件作廢 Revocation of Document Subject: NQJ & NQX & V1 SMT 治具清洗機作業規範 Doc No.: 901-K0156 REV: NQJ & NQX & V1 SMT Fixture Cleaner Operating Specification PAGE OF 目錄 CONTENTS 1.0 目的 PURPOSE 2.0 範圍 SCOPE 3.0 定義 DEFINITIONS 4.0 職責 RESPONSIBILITIES 4.1 生產線負責治具清洗及清洗機日常點檢。 The production line is responsible for cleaning of fixtures and daily inspection of the cleaner 4.2 工程單位負責治具清洗機 級保養、維修；治具&刮刀清洗後的檢查。 The engineering unit is responsible for Class cleaning and repairs of the cleaner and post-cleaning inspection of fixtures & scrapers 5.0 作業流程 FLOWCHART 6.0 作業內容 ACTIVITIES DESCRIPTION 6.1 清洗作業程序 Cleaning Operating Procedure 6.2 機器保養 Machine Care 6.3 治具&刮刀檢查 Inspection of Fixtures & Scrapers 7.0 參考資料 REFERENCES 7.1 901-K0126-03 SMT 載具點檢記錄表 901-K0126-03 (SMT Vehicle Check Record Sheet) 7.2 901-K0126-04 SMT 治具清洗記錄表 901-K0126-04 (SMT fixture cleaning record sheet) 7.3 902-N19-48 清洗機溶劑更換記錄表 902-N19-48 (cleaner solvent replacement record sheet) 7.4 902-N19-49 治具清洗機檢查記錄表 902-N19-49 (Fixture Cleaner Inspection Record Sheet) 8.0 附件 ATTACHMENTS 本資料為啟碁科技股份有限公司專有之財產，非經書面許可，不准透露或使用本資料，亦不准複印，複製或轉變成其他形式使用。 The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC Form No.: 2-JQ-021-04, 006 Document Content ■文件新增 Addition of Document □文件變更 Alteration of Document □文件作廢 Revocation of Document Subject: NQJ & NQX & V1 SMT 治具清洗機作業規範 Doc No.: 901-K0156 REV: NQJ & NQX & V1 SMT Fixture Cleaner Operating Specification PAGE OF 1.0 目的 PURPOSE 確保 SMT 印刷刮刀及 DIP 過爐載具清洗確實執行，避免因清洗不乾淨造成品質問題。 To ensure that SMT printing scrapers and DIP carriers that enter the furnace are precisely washed to prevent against quality issues as a result of non-thorough cleaning 2.0 範圍 SCOPE SMT 生產車間。 SMT production workshop 3.0 定義 DEFINITIONS N/A 4.0 職責 RESPONSIBILITIES 4.1 生產線負責治具清洗及清洗機日常點檢。 The production line is responsible for cleaning of fixtures and daily inspection of the cleaner 4.2 工程單位負責治具清洗機 級保養、維修；治具&刮刀清洗後的檢查。 The engineering unit is responsible for Class cleaning and repairs of the cleaner and post-cleaning inspection of fixtures & scrapers 本資料為啟碁科技股份有限公司專有之財產，非經書面許可，不准透露或使用本資料，亦不准複印，複製或轉變成其他形式使用。 The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC Form No.: 2-JQ-021-04, 006 Document Content ■文件新增 Addition of Document □文件變更 Alteration of Document □文件作廢 Revocation of Document Subject: NQJ & NQX & V1 SMT 治具清洗機作業規範 Doc No.: 901-K0156 REV: NQJ & NQX & V1 SMT Fixture Cleaner Operating Specification PAGE OF 5.0 作業流程 FLOWCHART 開始 Start 治具或刮刀放入待清洗槽 Place fixtures or scrapers in the washing chamber 關閉清洗機門後按 stare 開始清洗 Close the door of the cleaner and press START to begin washing 取出清洗後的治具或刮刀 Remove post-cleaning fixtures or scrapers 工程檢查 N Engineering unit checks 入庫 Warehoused 本資料為啟碁科技股份有限公司專有之財產，非經書面許可，不准透露或使用本資料，亦不准複印，複製或轉變成其他形式使用。 The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC Form No.: 2-JQ-021-04, 006 Document Content ■文件新增 Addition of Document □文件變更 Alteration of Document □文件作廢 Revocation of Document Subject: NQJ & NQX & V1 SMT 治具清洗機作業規範 Doc No.: 901-K0156 REV: NQJ & NQX & V1 SMT Fixture Cleaner Operating Specification PAGE OF 6.0 作業內容 ACTIVITIES DESCRIPTION 6.1 清洗作業程序 Cleaning Operating Procedure 6.1.1 將待清洗的治具或者刮刀放入待清洗槽內； Please fixtures or scrapers to be cleaned into the washing chamber 注意：治具放置不可堆疊以免影響清洗效果。 Attention: Do not stack fixtures in order to prevent against the cleaning outcome 6.1.2 用鑰匙將機器的電源打開。 Turn on power for the machine with a key 6.1.3 觸碰操作面板，機器進入菜單選項模式。 Touch the operator panel and the machine enters the menu mode 6.1.4 檢查顯示屏清洗液位和漂洗液位，是否顯示為中或高，若是處於低液位要及時添加。 Check the display screen to see if the cleaning liquid level and the washing solution level is medium or high; if it is low, it shall be added in a timely manner 本資料為啟碁科技股份有限公司專有之財產，非經書面許可，不准透露或使用本資料，亦不准複印，複製或轉變成其他形式使用。 The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC Form No.: 2-JQ-021-04, 006 Document Content ■文件新增 Addition of Document □文件變更 Alteration of Document □文件作廢 Revocation of Document Subject: NQJ & NQX & V1 SMT 治具清洗機作業規範 Doc No.: 901-K0156 REV: NQJ & NQX & V1 SMT Fixture Cleaner Operating Specification PAGE OF 6.1.5 液位確認好以後，點擊溶劑加熱開關到 30-60°範圍內。 Once the liquid levels are confirmed, click the solvent heating switch to 30-60° 6.1.6 檢查機器參數設置是否正確，清洗 1200s，漂洗 600s，烘乾 1200s。 Check if machine parameters are properly set; cleaning 1200s, rinsing 600s, drying 1200s 6.1.7 關閉上蓋點擊起動開關開始工作。 Close the upper lid and click Start to begin the task 本資料為啟碁科技股份有限公司專有之財產，非經書面許可，不准透露或使用本資料，亦不准複印，複製或轉變成其他形式使用。 The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC Form No.: 2-JQ-021-04, 006 Document Content ■文件新增 Addition of Document □文件變更 Alteration of Document □文件作廢 Revocation of Document Subject: NQJ & NQX & V1 SMT 治具清洗機作業規範 Doc No.: 901-K0156 REV: NQJ & NQX & V1 SMT Fixture Cleaner Operating Specification PAGE OF 6.2 機器保養 Machine Care 6.2.1 機器使用溶劑為：MEGA-7915，漂洗溶液為：自來水。 The solvent used for this machine is: MEGA-7915 and washing solution is: tap water 6.2.2 溶液更換週期為 周/次，每次更換 60L。每次更換完成後須記錄與『902-N19-48 清洗機 溶劑更換記錄表』 The solution is to be changed once every weeks; each time 60L is replaced After each replacement, it has to be documented in the “902-N19-48 (Cleaner Solvent Replacement Record Sheet).” 6.2.3 清洗機每月至少清潔溶劑槽及更換濾芯一次，並將保養結果 key 入 EMS 系統內。 The solvent tank is to be cleaned and the filter is to be replaced at least once a month for the cleaner and the care results are to be keyed into the EMS system 6.2.4 『902-N19-49 治具清洗機檢查記錄表』由 PD 完成，定義每天 10 點前完成點檢。 The “902-N19-49 (Fixture Cleaner Inspection Record Sheet)” is to be completed by the PD; the inspection shall be completed by 10 pm every day 6.3 治具&刮刀檢查 Inspection of Fixtures & Scrapers 6.3.1 清洗完成后，關閉幾台開關，取出治具&刮刀并整齊的裝入周轉框內。 After cleaning is completed, shut down the machine switch Remove the fixtures and scrapers and place them tidily into the turnover frame 6.3.2 將裝框治具&刮刀拉到鋼板室，放到治具待點檢放置區，需擺放整齊。 本資料為啟碁科技股份有限公司專有之財產，非經書面許可，不准透露或使用本資料，亦不准複印，複製或轉變成其他形式使用。 The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC Form No.: 2-JQ-021-04, 006 Document Content ■文件新增 Addition of Document □文件變更 Alteration of Document □文件作廢 Revocation of Document Subject: NQJ & NQX & V1 SMT 治具清洗機作業規範 Doc No.: 901-K0156 REV: NQJ & NQX & V1 SMT Fixture Cleaner Operating Specification PAGE OF The framed fixtures & scrapers are pulled to the stencil room and placed in the area pending inspection for fixtures; they need to be placed in a tidy manner 6.3.3 工程對治具&刮刀做點檢檢查，并做好『901-K0126-03 SMT 載具點檢記錄表』記錄 The engineering department inspects the fixtures and scrapers and keep records in the “901K0126-03 ( SMT Vehicle Check Record Sheet).” 7.0 參考資料 REFERENCES 7.1 901-K0126-03 SMT 載具點檢記錄表 901-K0126-03 (SMT Vehicle Check Record Sheet) 7.2 901-K0126-04 SMT 治具清洗記錄表 901-K0126-04 (SMT fixture cleaning record sheet) 7.3 902-N19-48 清洗機溶劑更換記錄表 902-N19-48 (cleaner solvent replacement record sheet) 7.4 902-N19-49 治具清洗機檢查記錄表 902-N19-49 (Fixture Cleaner Inspection Record Sheet) 8.0 附件 ATTACHMENTS 無 None 本資料為啟碁科技股份有限公司專有之財產，非經書面許可，不准透露或使用本資料，亦不准複印，複製或轉變成其他形式使用。 The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC Form No.: 2-JQ-021-04, 006 ... Document Subject: NQJ & NQX & V1 SMT 治具清洗機作業規範 Doc No.: 901- K0156 REV: NQJ & NQX & V1 SMT Fixture Cleaner Operating Specification PAGE OF 5.0 作業流程 FLOWCHART 開始 Start 治具或刮刀放入待清洗槽 Place fixtures or scrapers... Subject: NQJ & NQX & V1 SMT 治具清洗機作業規範 Doc No.: 901- K0156 REV: NQJ & NQX & V1 SMT Fixture Cleaner Operating Specification PAGE OF 6.0 作業內容 ACTIVITIES DESCRIPTION 6.1 清洗作業程序 Cleaning Operating. .. Revocation of Document Subject: NQJ & NQX & V1 SMT 治具清洗機作業規範 Doc No.: 901- K0156 REV: NQJ & NQX & V1 SMT Fixture Cleaner Operating Specification PAGE OF The framed fixtures & scrapers are pulled