Tài liệu TC ASTM C595 - 03 doc

... on 4.75-mm (No. 4) 2.36-mm (No. 8) 10 2.36-mm (No. 8) 1.18-mm (No 16) 25 1.18-mm (No. 16) 60 0- m (No. 30) 25 60 0- m (No. 30) 30 0- m (No. 50) 25 30 0- m (No. 50) 15 0- m (No. 100) 15 C595 03 5 cement, ... the slag-modified portland cement. 6.4 Air-Entraining Slag-Modified Portland Cement—Air- entraining slag-modified portland cement shall be slag- modified portland cement to which s...

Ngày tải lên: 21/01/2014, 09:20

... of ASTM Standards, Part 4. 3 Discontinued, see 1958 Book of ASTM Standards, Part 4. 4 Annual Book of ASTM Standards, Vol 04.02. 5 Annual Book of ASTM Standards, Vol 04.01. 6 Annual Book of ASTM ... Industrial Chemicals 6 E 203 Test Method for Water Using Karl Fischer Reagent 6 3. Materials 3.1 Cements: 1 This specification is under the jurisdiction of ASTM Committee C-1 on Cement...

Ngày tải lên: 21/01/2014, 09:20

... standard to establish appro- priate safety and health practices and determine the applica- bility of regulatory limitations prior to use. 2. Referenced Documents 2.1 ASTM Standards: C 114 Test ... identification num- ber and the stopper, if not interchangeably ground, shall bear the same number. Interchangeable ground-glass parts shall be marked on both members with the standard-taper symbol...

Ngày tải lên: 21/01/2014, 09:20

... m/s22m,50 0  gRvR . 3.4: jiv ˆ 3 ˆ 2 2 ctbt   . This vector will make a 45 -angle with both axes when the x- and y-components are equal; in terms of the parameters, this time is cb 32 . 3.5: ... tαvx )cos( 0  , assuming the match starts out at 0x and 0y . When the match goes in the wastebasket for the minimum velocity, Dy 2 and Dx 6 . When the match goes in the wasteb...

Ngày tải lên: 10/12/2013, 12:15

... 4). N OTE 3—The compressive strengths of nominal 2-in. [50-mm] diam- eter cores are known to be somewhat lower and more variable than those of nominal 4-in. [100-mm] diameter cores. In addition, smaller ... MacGregor, J.G, “Effect of Core Length-to-Diameter Ratio on Concrete Core Strengths,” ACI Materials Journal, Vol. 91, No. 4, July-August 1994, pp. 33 9-3 48. C 42/C 42M – 03 3 7.10.5 T...

Ngày tải lên: 24/12/2013, 03:17

... of ASTM Standards, Vol 04.01. 3 Annual Book of ASTM Standards, Vol 04.02. 4 Annual Book of ASTM Standards, Vol 14.02. 1 Copyright © ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 1942 8-2 959, ... 25-mm (3 5 ⁄ 32 by 1-in.), shell-type, with tight-fitting stoppers or caps. 4.6 Drying Oven, maintained at 100 to 110°C. 4.7 Weighing Bottles, approximately 40 mm high and 25 mm wide, wi...

Ngày tải lên: 24/12/2013, 03:17

... of ASTM Standards, Vol 04.01. 3 Annual Book of ASTM Standards, Vol 11.01. 4 Annual Book of ASTM Standards, Vol 14.02. 1 Copyright © ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 1942 8-2 959, ... standard to establish appro- priate safety and health practices and determine the applica- bility of regulatory limitations prior to use. 2. Referenced Documents 2.1 ASTM Standards: C...

Ngày tải lên: 21/01/2014, 09:20

... 688 – 96. 2 Annual Book of ASTM Standards, Vol 04.02. 3 Annual Book of ASTM Standards, Vol 04.01. 1 Copyright © ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 1942 8-2 959, United States. some ... with mini- mum air contact. 8.1.6 Compressive Strength—For functional additions hav- ing no water-reducing effects, use Test Method C 109. For functional additions having some water-reduc...

Ngày tải lên: 21/01/2014, 09:20