Tài liệu Configuring Frame Relay Subinterfaces pptx

... PVC. Step 8 Show the Frame Relay maps a. Look at the frame relay maps by typing the command show frame- relay map at the privileged EXEC mode prompt: Amsterdam#show frame- relay map b. What ... Lab 5.2.5 Configuring Frame Relay Subinterfaces Objective • Configure three routers in a full-mesh Frame Relay network. Background/Preparation An Adtran Atla...

Ngày tải lên: 18/01/2014, 05:20

... 5.2.3 Configuring Frame- Relay Subinterfaces Objective • Configure three routers in a full-mesh Frame Relay network. An Adtran Atlas550 Frame Relay emulator is used to simulate the switch /Frame ... PVC. Step 8 Show the Frame Relay maps a. Look at the frame relay maps by typing the command show frame- relay map at the privileged exec mode prompt: Amsterda...

Ngày tải lên: 18/01/2014, 05:20

... lab. Step 2 Configuring the serial interface a. In Frame Relay, the customer router is considered the DTE device. In order to configure the serial interface the Layer 2 Frame Relay frame type ... the frame type, use the following commands: Cork#configure terminal Cork(config)#interface serial 0 Cork(config-if)#encapsulation frame- relay IETF b. Next the format of...

Ngày tải lên: 18/01/2014, 05:20

... 5.2.2 Configuring Frame Relay PVC Objective • Configure two routers back-to-back as a Frame Relay permanent virtual circuit (PVC). This will be done manually, in the absence of a Frame Relay ... White (091-6543211) Step 6 Verifying Frame Relay PVC a. On the Washington router, type the command show frame- relay pvc: Washington#show frame- relay pvc b. Wha...

Ngày tải lên: 18/01/2014, 05:20

... 5.2.3 Configuring Frame- Relay Subinterfaces Objective • Configure three routers in a full-mesh Frame Relay network. An Adtran Atlas550 Frame Relay emulator is used to simulate the switch /Frame ... PVC. Step 8 Show the Frame Relay maps a. Look at the frame relay maps by typing the command show frame- relay map at the privileged exec mode prompt: Amsterda...

Ngày tải lên: 11/12/2013, 14:15

... PVC. Step 8 Show the Frame Relay maps a. Look at the frame relay maps by typing the command show frame- relay map at the privileged EXEC mode prompt: Amsterdam#show frame- relay map b. What ... Lab 5.2.5 Configuring Frame Relay Subinterfaces Objective • Configure three routers in a full-mesh Frame Relay network. Background/Preparation An Adtran Atla...

Ngày tải lên: 11/12/2013, 14:15

... Show frame- relay pvc Command Field Descriptions Field Description DLCI One of the DLCI numbers for ... this PVC Dropped Pkts Number of incoming and outgoing packets dropped by the router at the Frame Relay level In FECN Pkts Number of packets received with the FECN bit set In BECN Pkts

Ngày tải lên: 11/12/2013, 14:15

... broadcast frame- relay lmi-type ansi Remove the incorrect frame- relay map statement. Singapore(config-if)#no frame- relay map ip 192.168.192.2 17 broadcast Reenter the frame- relay map ... address via a “static” frame- relay map statement. “CISCO” identifies the Frame Relay encapsulation used with frame- relay map statement, which is the default Frame Re...

Ngày tải lên: 11/12/2013, 14:15

... was miconfigured on the Singapore router (frame- relay interface-dlci 17 instead of frame- relay interface-dlci 18). Early in the LMI process, the Frame Relay switch sends the router all of the ... Turn debug frame- relay packet off. Singapore#no debug frame- relay packet or no debug all 4. Based upon the map being dynamically established and output from the debug fra...

Ngày tải lên: 11/12/2013, 14:15

... encapsulation frame- relay no ip mroute-cache cdp enable frame- relay interface-dlci 18 frame- relay lmi-type ansi As was discovered earlier, the encapsulation is frame- relay and the frame- relay ... information about each router. • show interface • show frame- relay lmi • show frame- relay pvc • show frame- relay map • debug frame- relay lmi G...

Ngày tải lên: 11/12/2013, 14:15