Tài liệu ISIS Lab Scenario I pdf
Tài liệu ISIS Lab Scenario I pdf
... Ethernet0
ip address 150.100.0.194 255.255.255.240
no ip directed-broadcast
ip router isis
isis password CZadj level-1
isis priority 127
isis hello-interval 30
!
interface Serial0
no ip address
... router isis
!
interface Serial0
ip address 150.100.0.209 255.255.255.240
ip router isis
no fair-queue
clockrate 2000000
isis metric 20
isis password CZadj level-1
!
inte...
Tài liệu DDR Lab Scenario 2 - Dialer Profiles with Authentication pdf
... password cisco
The next step in our configuration is to define interesting traffic.
4. Define Interesting Traffic Using Dialer Lists
A dialer-list is used to define "interesting traffic" ... ISDN simulator or actual ISDN lines)
ISDN Information for Router1:
isdn switch-type basic-ni
isdn spid1 0835866101 8358661
isdn spid2 0835866301 8358663
ISDN Information for router2:
isdn switch...
Tài liệu Trading Greenspan, Part I(pdf) pdf
...
market, similar reactions can be anticipated there, too, especially in the interest
rate-sensitive groups such as financials and consumer cyclicals.
Copyright © 2001 by TradingMarkets.com, Inc.
...
testimony and the cumulative reaction is usually double that of the initial
reaction. It goes on: one month later, the reaction nearly doubles again
(also in the same direction).
Ost...
Tài liệu ISDN Lab Scenario 1 -- OSPF Build to Specifications docx
... 16
http://www.certificationzone.com/studyguides /?Issue=24&IssueDate=11-01-2000&CP= 11/06/01
Date of Issue: 11-01-2000
ISDN Lab Scenario 1 OSPF Build to
Specifications
Introduction
This lab is designed ... wrong administrative distance in the static route. The administrative distance must be
greater than RIP's administrative distance of 120. I used 200.
7. 7. R1 is mis...
Tài liệu AppleTalk Lab Scenario One ppt
... Scenario One:
Troubleshooting Basic AppleTalk
Configuration
Introduction
Equipment Required
Scenario Background
Success Criteria
Procedure
Initial Configurations
Passwords
Tips and Debriefing
Configuration ... One
Troubleshooting Basic AppleTalk
Configuration
by Priscilla Oppenheimer
Introduction
In this scenario, you will be asked to troubleshoot the AppleTalk internetwork shown in...
Tài liệu AppleTalk Lab Scenario One doc
... AppleTalk internetwork shown in Figure 1.
Figure 1
Lab Scenario One:
Troubleshooting Basic AppleTalk
Configuration
Introduction
Equipment Required
Scenario Background
Success Criteria
Procedure
Initial ... criteria.
Initial Configurations
Each router's initial configuration can be accessed by clicking on the following links:
• Monroe
• Bogart
• Gable
• Fonda
Passwords
The config...
Tài liệu CCIE Lab Scenario 2 Configuring A Terminal Server ppt
... such as a Cisco 2509 or 2511. Although this is a
relatively simple lab, mastery of this material is critically important. If you cannot fully configure a terminal server in
five minutes or less, ...
Server
by David Wolsefer
Introduction
Equipment Needed
Configuration Tasks
Using the Terminal Server
Final Configuration
Introduction
This lab teaches the reader to configure and use a term...
Tài liệu DDR Lab Scenario 1 - Legacy DDR Walk Through doc
... Final Configuration
Router 2's Final Configuration
Introduction
This lab is designed to walk you through a basic ISDN DDR configuration. This lab will show you what commands to
type in ... Here is the basic
starting point for cabling your equipment:
ISDN Information for Router1:
isdn switch-type basic-ni
isdn spid1 0835866101 8358661
isdn spid2 0835866301 8358663
ISDN Information...
Tài liệu OSPF Lab Scenario 1 - Classless and Discontiguous Networks pptx
... 0.0.0.1
[IE-OSPF1-LS1-F03]
[2001-05-30-02]
Copyright © 2001 Genium Publishing Corporation
CertificationZone Page 2 of 3
http://www.certificationzone.com/studyguides /?Issue=38&IssueDate=06-01-2001&CP= ... initializes. With increasing numbers of
routers, you will have more and more debug traffic you have been warned! Simply record the traffic for later
analysis; it will go by too fa...
Tài liệu C++ Lab 1 Introduction pdf
...
#include <iostream> //this is preprocessor directive
using namespace std; //using directive
int main () //this is the main function
{
int i, j,k,l, m,n;
float a,b,c;
//integer ... is it 9? We assigned these
numbers to integer variables, which discards the fractional part leaving 6 and 3,
which give a total of 9. How about 10/9 yielding 3? This is called integer
divis...