Tài liệu Lab 5 1 3 Using the Boot System Command doc

... Enter. The router is ready for the assigned lab to be performed. 1 - 5 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 5. 1. 3 Copyright  20 03, Cisco Systems, Inc. Lab 5. 1. 3 Using the Boot System ... #1 Serial Interface #2 Interface #5 800 (806) Ethernet 0 (E0) Ethernet 1 (E1) 16 00 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S...

Ngày tải lên: 18/01/2014, 04:20

... Serial 1 (S1) 17 00 FastEthernet 0 (FA0) FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1) 250 0 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1) 2600 FastEthernet 0/0 (FA0/0) FastEthernet ... Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2 Interface #5 800 (806) Ethernet 0 (E0) Ethernet 1 (E1) 16 00 Ethern...

Ngày tải lên: 18/01/2014, 04:20

... 1 - 2 CCNA 1: Networking Basics v 3. 0 - Lab 5. 1. 3 Copyright  20 03, Cisco Systems, Inc. Lab 5. 1. 3 Connecting Router LAN Interfaces Objective • Identify the Ethernet ... an Ethernet 10 /10 0 NIC installed • One Ethernet switch or hub • One router with an RJ- 45 Ethernet or Fast Ethernet interface or an AUI interface • 10 BASE-T AUI transcei...

Ngày tải lên: 24/01/2014, 19:20

... 15 ALSwitch(config-line)# password cisco ALSwitch(config-line)# login ALSwitch(config-line)# ALSwitch(config-line)#interface Vlan1 ALSwitch(config-if)# ip address 19 2 .16 8 .1. 2 255 . 255 . 255 .0 ... ___________________________________________________________________ Step 5 Determine the MAC addresses that the switch has learned a. To determine the what MAC addresses the...

Ngày tải lên: 18/01/2014, 04:20

... 1 - 2 CCNA 1: Networking Basics v 3. 0 - Lab 5. 1. 4 Copyright  20 03, Cisco Systems, Inc. Lab 5. 1. 4 RJ- 45 Jack Punch Down Objective • Learn the correct process for ... area to the network. It is important to use CAT 5 or 5e rated jacks and patch panels with CAT 5 or 5e cabling in order to support Fast Ethernet (10 0 Mbps) and Gigabit Ethernet (10 00 Mbps)....

Ngày tải lên: 24/01/2014, 19:20

... Address Ethernet 0 Address Subnet mask (all interfaces) Router 1 GAD DCE 56 000 19 2 .16 8. 15 . 1 192 .16 8 .14 .1 255 . 255 . 255 .0 Router 2 BHM DTE Not set 19 2 .16 8. 15 . 2 19 2 .16 8 .16 .1 255 . 255 . 255 .0 ... 16 00, 17 00, 250 0 and 2600 routers, or a combination. Refer to the chart at the end of the lab to correctly identify the interface identifiers...

Ngày tải lên: 11/12/2013, 14:15

... PCs to their original IP settings, disconnect the equipment, and store the cables 1 - 4 CCNA 1: Networking Basics v 3. 0 - Lab 5. 1. 13b Copyright  20 03, Cisco Systems, Inc. Lab 5. 1. 13b Building ... Basics v 3. 0 - Lab 5. 1. 13b Copyright  20 03, Cisco Systems, Inc. • Two workstations with an Ethernet 10 /10 0 NIC installed • Ethernet 10 BaseT or Fast Ethe...

Ngày tải lên: 11/12/2013, 14:15

... Ethernet 1 (E1) 16 00 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1) 17 00 FastEthernet 0 (FA0) FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1) 250 0 Ethernet 0 (E0) Ethernet 1 (E1) Serial ... Muller (+ 31 20 6 23 32 67) Circuit #KPN4 655 55 Berlin(config-if)#ip address 19 2 .16 8 .5. 2 255 . 255 . 255 .0 Berlin(config-if)#frame-relay interface-dlci 3 01...

Ngày tải lên: 11/12/2013, 14:15

... 1 (S1) 17 00 FastEthernet 0 (FA0) FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1) 250 0 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1) 2600 FastEthernet 0/0 (FA0/0) FastEthernet ... View > Log File. The output should be similar to the following: Mon Sep 16 14 :10 :08 2002: Receiving ‘startup-config’ file from 19 2 .16 8 . 13 .1 in binary mode Mon Se...

Ngày tải lên: 11/12/2013, 14:15

... networks 19 2 .16 8 .1. 0 and 19 2 .16 8.2.0. Router E0 Interface IP Address Subnet mask Router – A 19 2 .16 8 .1. 1 255 . 255 . 255 .0 Router – B 19 2 .16 8.2 .1 255 . 255 . 255 .0 b. Connecting the cables The connection ... Router – A DCE 19 2 .16 8 .3 .1 255 . 255 . 255 .0 Router – B DTE 19 2 .16 8 .3. 2 255 . 255 . 255 .0 b. Connecting the cables The DCE cable...

Ngày tải lên: 11/12/2013, 14:15