Tài liệu Lab 5 1 3 Using the Boot System Command pptx

... 1 - 5 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 5. 1. 3 Copyright  20 03, Cisco Systems, Inc. Lab 5. 1. 3 Using the Boot System Command Objective • Display information about the Cisco ... in this lab assignment before continuing. 2 - 5 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 5. 1. 3 Copyright  20 03, Cisco Systems, Inc. Step 1...

Ngày tải lên: 18/01/2014, 04:20

... 1 - 5 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 5. 1. 3 Copyright  20 03, Cisco Systems, Inc. Lab 5. 1. 3 Using the Boot System Command Objective • Display information about the ... passwords Router 1 AD class cisco 2 - 5 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 5. 1. 3 Copyright  20 03, Cisco Systems, Inc. a. Enter enable...

Ngày tải lên: 18/01/2014, 04:20

... 1 - 2 CCNA 1: Networking Basics v 3. 0 - Lab 5. 1. 3 Copyright  20 03, Cisco Systems, Inc. Lab 5. 1. 3 Connecting Router LAN Interfaces Objective • Identify the Ethernet ... an Ethernet 10 /10 0 NIC installed • One Ethernet switch or hub • One router with an RJ- 45 Ethernet or Fast Ethernet interface or an AUI interface • 10 BASE-T AUI transcei...

Ngày tải lên: 24/01/2014, 19:20

... Required PC – B 19 2 .16 8 .1. 2 255 . 255 . 255 .0 Not Required Step 5 Access the Command or MS-DOS prompt a. Use the Start menu to open the Command Prompt (MS-DOS-like) window: Windows 95 / 98 / Me users ... 1 - 4 CCNA 1: Networking Basics v 3. 0 - Lab 5. 1. 13b Copyright  20 03, Cisco Systems, Inc. Lab 5. 1. 13b Building a Switch-based Network Objecti...

Ngày tải lên: 11/12/2013, 14:15

... the workstation a. The configuration for the host connected to the Gadsden Router is: IP Address 19 2 .16 8 .14 .2 IP subnet mask 255 . 255 . 255 .0 Default gateway 19 2 .16 8 .14 .1 Step 3 Login to the ... Sep 16 14 :10 :08 2002: Receiving ‘startup-config’ file from 19 2 .16 8 . 13 .1 in binary mode Mon Sep 16 14 :11 :14 2002: Successful. Step 8 Copy the startup...

Ngày tải lên: 11/12/2013, 14:15

... Address Ethernet 0 Address Subnet mask (all interfaces) Router 1 GAD DCE 56 000 19 2 .16 8. 15 . 1 192 .16 8 .14 .1 255 . 255 . 255 .0 Router 2 BHM DTE Not set 19 2 .16 8. 15 . 2 19 2 .16 8 .16 .1 255 . 255 . 255 .0 2 - ... 16 00, 17 00, 250 0 and 2600 routers, or a combination. Refer to the chart at the end of the lab to correctly identify the interface identifi...

Ngày tải lên: 11/12/2013, 14:15

... Amsterdam, DLCI 3 01, Contact Peter Muller (+ 31 20 6 23 32 67) Circuit #KPN4 655 55 Berlin(config-if)#ip address 19 2 .16 8 .5. 2 255 . 255 . 255 .0 Berlin(config-if)#frame-relay interface-dlci 3 01 Berlin(config-if)#interface ... Amsterdam, DLCI 2 01, Contact Peter Muller (+ 31 20 6 23 32 67) Circuit #KPN4 655 55 Paris(config-if)#ip address 19 2 .16 8.4.2 255 . 255 . 255...

Ngày tải lên: 11/12/2013, 14:15

... Router – A DCE 19 2 .16 8 .3 .1 255 . 255 . 255 .0 Router – B DTE 19 2 .16 8 .3. 2 255 . 255 . 255 .0 b. Connecting the cables The DCE cable will attach to the Serial 0 interface on Router A. The DTE cable should ... 255 . 255 . 255 .0 19 2 .16 8 .1. 1 PC – B 19 2 .16 8.2.2 255 . 255 . 255 .0 19 2 .16 8.2 .1 Step 9 Verify that PCs can communicate across the WAN a. Ac...

Ngày tải lên: 11/12/2013, 14:15

... 0 15 ALSwitch(config-line)#password cisco ALSwitch(config-line)#login ALSwitch(config-line)# ALSwitch(config-line)#interface Vlan1 ALSwitch(config-if)#ip address 19 2 .16 8 .1. 2 255 . 255 . 255 .0 ... - 7 CCNA 3: Switching Basics and Intermediate Routing v 3. 0 - Lab 6.2 .3 Copyright  20 03, Cisco Systems, Inc. Erasing and Reloading the Switch For the majority of the lab...

Ngày tải lên: 18/01/2014, 04:20

... 15 ALSwitch(config-line)# password cisco ALSwitch(config-line)# login ALSwitch(config-line)# ALSwitch(config-line)#interface Vlan1 ALSwitch(config-if)# ip address 19 2 .16 8 .1. 2 255 . 255 . 255 .0 ... continuing. 1 - 7 CCNA 3: Switching Basics and Intermediate Routing v 3. 0 - Lab 6.2 .3 Copyright  20 03, Cisco Systems, Inc. Step 1 Configure the switch Configure the h...

Ngày tải lên: 18/01/2014, 04:20