Tài liệu Nghệ thuật xếp hình Nhật Bản:dragonfly 2 docx

... right. 2 22. Flip 1 flap over, and pull the next flap towards the left. Model won’t lie flat. 22 -23 24 . Repeat 22 -23 on left. Turn over. 25 . Fold top point to center. Turn back over. 26 . Valley ... downwards. Don’t crease. 20 . Reverse-fold, flipping over the rectangular single-ply. Press flat and sharpen all creases. 16 -20 21 . Repeat 16 -20 on left. Turn over. not to corne...

Ngày tải lên: 17/01/2014, 04:20

... Hummingbird - Collin Weber Page 2 of 4 Hummingbird - Collin Weber Page 4 of 4 Hummingbird - Collin Weber Page 3 of 4

Ngày tải lên: 09/12/2013, 16:15

... convexes outwards. 26 . 27 . 28 . 29 . 30. 31. 32. Now valley fold then unfold Steps 25 and 26 . Lift up the first layer then fold in the left corner along creases made in Step 26 . Fold the next ... assembly as shown. 20 . 21 . 22 . Valley fold then crimp fold each side. Fold assembly in half while lifting out the layer at the top and a triangle at the bottom 1/4 23 . 24...

Ngày tải lên: 10/12/2013, 12:15

... right. 2 22. Flip 1 flap over, and pull the next flap towards the left. Model won’t lie flat. 22 -23 24 . Repeat 22 -23 on left. Turn over. 25 . Fold top point to center. Turn back over. 26 . Valley ... downwards. Don’t crease. 20 . Reverse-fold, flipping over the rectangular single-ply. Press flat and sharpen all creases. 16 -20 21 . Repeat 16 -20 on left. Turn over. not to corne...

Ngày tải lên: 10/12/2013, 12:15

Ngày tải lên: 10/12/2013, 12:15

Ngày tải lên: 21/12/2013, 03:15

... front. 20 . Finished from on top 21 . Finished from the side. Klingon D-7 Battle Cruiser By Perry Bailey Copyright 1997, and 20 00 1. Start with bill facing up fold in half, crease and unfold. 2. Fold ... diagonls across the bill and a valley fold between the two x’s. 4. Using the diamond formed by the 2 big x,s swivel fold out the end of the bill as you fold it over. 5.Should look...

Ngày tải lên: 17/01/2014, 04:20

... Dragonfly (continued) Copyright 1998-99 Stephen Hecht. All Rights Reserved 22 -27 28 . Repeat 22 -27 on left. Turn over. 29 . Detail of top point. Fold and unfold tip down to base of triangle. 30. ... upper wing downwards. 20 . Reverse-fold, flipping the single-ply over. Sharpen all creases. 16 -20 21 . Repeat 16 -20 on left. Turn over. 3 22 . Flip 1 flap over, and pull the next 2...

Ngày tải lên: 17/01/2014, 04:20

... 22 .Swing over. 23 .Petal up. 24 .Swing up. 27 .Valley outwards .26 .Swing down .25 .Sink triangularly. 28 .Precrease flap halfway. 29 .Valley along precrease. 30.Valley ... base of model. 32. Pull up the thick set of layers31.Swing over flap A, while incorporating a reverse fold. A gusset will form where flap A meets the point. Flap A Edge B 22 -33 1 /2 36-37,39-40 3-5 34.Repeat ......

Ngày tải lên: 24/01/2014, 07:20

... 12. 13. 14. ❴✎❵✦❬★❛✪❜✫❭✭❝✮❭✭❞✰❝✱❩✌❡ ❢✵❣✛❤★❤◆✐  ✂✁☎✄✝✆✟✞✡✠☛✁✌☞✎✍✑✏✓✒✕✔✗✖✙✘✛✚✢✜✙✣ 1/3 7. 1/ 12 6. 1. 2. 1/ 121 / 12 8. 1−4 4. 3. 5. I. PRECREASES. ✤✎✥✦✘★✧✪✩✫✚✭✬✮✚✭✯✰✬✱✖✌✲ ✳✵✴✛✶★✶ ✜ ✷✂✸☎✹✝✺✟✻✡✼☛✸✌✽✎✾✑✿✓❀✕❁✗❂✙❃✛❄❆❅❈❇ o 180 1/ 12 6. 7. o 90 o 1. 90 o 90 o 90 o 2. 3. 5.4. 8. 9. 10. II. ... ✿◆✻❖✽◗❘✷❚❙✌❅✲✺❋●✚❯✄✳✲●✭❅✡✯✲✱✴❙❲❱✩❇❚●❳■❋✳✲❂❲❍✌❊❋❅❆●✭❯✄✱ ❨ ❂✆❩✗❂✚❬❭✵✸✷❉❍❲✯✲✺❫❪❀✷❚❙✌❅✲✺✤❑ ❴✭❵❜❛◗❝ ✦✩❞ ❝...

Ngày tải lên: 09/12/2013, 16:15