Tài liệu Nghệ thuật xếp hình Nhật Bản:shark 2 docx

... right. 2 22. Flip 1 flap over, and pull the next flap towards the left. Model won’t lie flat. 22 -23 24 . Repeat 22 -23 on left. Turn over. 25 . Fold top point to center. Turn back over. 26 . Valley ... downwards. Don’t crease. 20 . Reverse-fold, flipping over the rectangular single-ply. Press flat and sharpen all creases. 16 -20 21 . Repeat 16 -20 on left. Turn over. not to corne...

Ngày tải lên: 17/01/2014, 04:20

... Hummingbird - Collin Weber Page 1 of 4 Hummingbird - Collin Weber Page 2 of 4 Hummingbird - Collin Weber Page 3 of 4

Ngày tải lên: 09/12/2013, 16:15

... and crease firmly. 26 . 27 . 28 . 29 . 30. 31. 32. Now valley fold then unfold Steps 25 and 26 . Lift up the first layer then fold in the left corner along creases made in Step 26 . Fold the next ... assembly as shown. 20 . 21 . 22 . Valley fold then crimp fold each side. Fold assembly in half while lifting out the layer at the top and a triangle at the bottom 1/4 23 . 24...

Ngày tải lên: 10/12/2013, 12:15

... right. 2 22. Flip 1 flap over, and pull the next flap towards the left. Model won’t lie flat. 22 -23 24 . Repeat 22 -23 on left. Turn over. 25 . Fold top point to center. Turn back over. 26 . Valley ... downwards. Don’t crease. 20 . Reverse-fold, flipping over the rectangular single-ply. Press flat and sharpen all creases. 16 -20 21 . Repeat 16 -20 on left. Turn over. not to corne...

Ngày tải lên: 10/12/2013, 12:15

Ngày tải lên: 10/12/2013, 12:15

... side. 19. Zoom out. 20 . Mountain fold the tip behind. 23 . Inside reverse fold the innermost layer. 22 . [Enlarged view.] Collapse the near and far sides against the body. 21 . Fold in half, forming ... lay flat. 24 . Wrap a layer around to the front. Repeat behind. 25 . Fold the near side up. Repeat behind. 26 . Inside reverse fold. Repeat behind. 27 . Fold corner up. Repeat behind....

Ngày tải lên: 10/12/2013, 12:15

Ngày tải lên: 21/12/2013, 03:15

... next view is enlarged. 11. Fold the entire model in half (the model is a bit thick here). 1 /2 1 /2 12. Mark the half way point on the long flap, fold the flaps at the back up as shown. open the ... Klingon D-7 Battle Cruiser By Perry Bailey Copyright 1997, and 20 00 1. Start with bill facing up fold in half, crease and unfold. 2. Fold the edges in to the center. 3. Fold two diagonls...

Ngày tải lên: 17/01/2014, 04:20

... over. 12. Precrease. 17.Swing down. 18.Open out top. 21 .Sink halfway .20 .Squash.19.Collapse into rabbit-ear formation. 22 .Swing over. 23 .Petal up. 24 .Swing up. 27 .Valley outwards .26 .Swing down .25 .Sink ... reverse fold. A gusset will form where flap A meets the point. Flap A Edge B 22 -33 1 /2 36-37,39-40 3-5 34.Repeat steps 22 -33 on the other side. 35. Valley. Rotate model...

Ngày tải lên: 24/01/2014, 07:20

... side. 19. Zoom out. 20 . Mountain fold the tip behind. 23 . Inside reverse fold the innermost layer. 22 . [Enlarged view.] Collapse the near and far sides against the body. 21 . Fold in half, forming ... lay flat. 24 . Wrap a layer around to the front. Repeat behind. 25 . Fold the near side up. Repeat behind. 26 . Inside reverse fold. Repeat behind. 27 . Fold corner up. Repeat behind....

Ngày tải lên: 24/01/2014, 07:20